68K System Monitor User's Guide

Manual text content

g GE Energy Systems Document Number : SWM0023 Version : 1.00 Revision : 2 Date : 20-Mar-2002 Classification : General, Full Release 68K System Monitor User's Guide SWM0023 1.00 2 General ii Full Release NOTICE OF COPYRIGHT & PROPRIETARY RIGHTS © 2002, General Electric Canada Inc. All rights reserved. The contents of this manual are the property of General Electric Canada Inc. No part of this work may be reproduced or transmitted in any form or by any means, except as permitted in written license agreement with General Electric Canada Inc. General Electric Canada Inc. has made every reasonable attempt to ensure the completeness and accuracy of this document. However, the information contained in this manual is subject to change without notice, and does not represent a commitment on the part of General Electric Canada Inc. Any attached hardware schematics and technical descriptions, or software listings that disclose source code, are for information purposes only. Reproduction in whole or in part to create working hardware or software for other than General Electric Canada Inc. products is strictly prohibited, except as permitted by written license agreement with General Electric Canada Inc. TRADEMARK NOTICES WESDAC is a registered trademark of General Electric Company, General Electric Canada Inc. and/or GE Harris Energy Control Systems Canada, Inc. All other brand and product names mentioned in this document are trademarks or registered trademarks of their respective companies. 68K System Monitor User's Guide GE Energy Services General SWM0023-1.00 -2 Full Release iii Modification Record VERSION REVISION DATE INITIALS COMMENT 1 28-Feb-2002 RFN Created 1.00 2 20-Mar-2002 RFN Corrected errors as per review GE Energy Services 68K System Monitor User's Guide SWM0023 1.00 2 General iv Full Release General SWM0023-1.00 -2 Full Release v Table of Contents About This Document Purpose and Audience of this User’s Guide................................................................................. viii Support Services and Training ........................................................................................................ix Chapter 1: Connecting and Using the 68K Monitor Connecting to the 68K Monitor ................................................................................................... 1-2 Command Input and Response..................................................................................................... 1-3 68K Monitor Display ................................................................................................................... 1-6 Error Messages ........................................................................................................................ 1-7 Chapter 2: Command Grouping General System Commands ......................................................................................................... 2-2 Diagnostic Commands ................................................................................................................. 2-3 Memory Commands..................................................................................................................... 2-4 Process Commands ...................................................................................................................... 2-5 Exchange Commands................................................................................................................... 2-6 Breakpoint Commands................................................................................................................. 2-7 Configuration Maintenance Commands....................................................................................... 2-8 Chapter 3: 68K Monitor Commands Section 1: Command / Platform Cross-Reference ........................................................................... 3-2 Platform-Specific Commands ...................................................................................................... 3-2 Section 2: Monitor Commands ........................................................................................................ 3-4 AL - Change Auto-logout Timer.......................................................................... 3-4 BAUD - Set Baud Rate .............................................................................................. 3-5 BOOT - Startup.......................................................................................................... 3-7 CACHE - Control Cache.............................................................................................. 3-8 CAL - Calibrate KI ................................................................................................. 3-9 CB - Clear Breakpoint........................................................................................ 3-10 CCA - Change Configuration File Attributes ....................................................... 3-11 CCB - Create Configuration Storage Block.......................................................... 3-12 CCF - Clear Configuration File............................................................................ 3-14 CF - Copy File ................................................................................................... 3-15 CLS - Clear Screen............................................................................................... 3-16 CP - Change Priority.......................................................................................... 3-17 CS - Check Sum................................................................................................. 3-18 D - Dump Memory .......................................................................................... 3-19 DB - Define Breakpoint ..................................................................................... 3-21 DEBUG - Debug Mode .............................................................................................. 3-22 DF - Display File Data....................................................................................... 3-23 DHW - Display Hardware Data ............................................................................. 3-24 DIR - Directory.................................................................................................... 3-25 DL - Download .................................................................................................. 3-27 DM - Debug Mode .............................................................................................. 3-28 GE Energy Services 68K System Monitor User's Guide SWM0023 1.00 2 General vi Full Release DSTAT - Decompression Status ............................................................................... 3-29 E - Edit Memory.............................................................................................. 3-30 ECHO - Echo Toggle............................................................................................... 3-32 EL - Error Log ................................................................................................... 3-33 ERASE - Flash Erase................................................................................................. 3-34 ETH - Ethernet Address ....................................................................................... 3-35 EXIT - Exit ............................................................................................................ 3-36 F - Fill Memory............................................................................................... 3-37 FT - Find Table.................................................................................................. 3-38 HE or HELP - Help ........................................................................................................... 3-39 HT - HDLC Test ................................................................................................ 3-40 IMG - Display Image Information........................................................................ 3-41 JTF - Jump To Flash ........................................................................................... 3-42 JX - Jam Exchange ............................................................................................ 3-43 KIM - KI Metrics.................................................................................................. 3-44 M - Move Memory ........................................................................................... 3-45 PB - Print Breakpoint......................................................................................... 3-46 PR - Profile ........................................................................................................ 3-47 PRG - Program Flash............................................................................................ 3-49 QC - Query Configuration Storage Parameters.................................................. 3-50 QP - Query Process............................................................................................ 3-51 QR - Query RAM ............................................................................................... 3-53 QX - Query Exchange ........................................................................................ 3-54 RB - Resume Breakpoint ................................................................................... 3-56 RP - Resume Process ......................................................................................... 3-57 RR - Report RAM Partitions.............................................................................. 3-58 RT - RAM Test .................................................................................................. 3-59 RTB - Return To BootROM................................................................................. 3-61 RTC - Test CCU RTC .......................................................................................... 3-62 RX - Request Exchange ..................................................................................... 3-63 RZ - ZMODEM Download................................................................................ 3-64 SA - Serial Analyzer .......................................................................................... 3-66 SB - Step Breakpoint ......................................................................................... 3-68 SC - Select Active Configuration ...................................................................... 3-69 SET - Set System Parameters .............................................................................. 3-70 SI - Display System Information...................................................................... 3-71 SP - Suspend Process ........................................................................................ 3-72 ST - Serial Test.................................................................................................. 3-74 SX - Send Exchange .......................................................................................... 3-76 SYSC - System ....................................................................................................... 3-77 TEST - Invoke Test Tool........................................................................................ 3-78 TR - Trace .......................................................................................................... 3-79 UL - Upload ....................................................................................................... 3-81 VER - Version ...................................................................................................... 3-82 VP - Signal Process............................................................................................ 3-83 WINM - WIN Metrics.............................................................................................. 3-84 Index General SWM0023-1.00 -2 Full Release vii About This Document Overview Introduction The 68K Monitor is a feature of all GE Energy Services products that use a variant of the Motorola 68000 series of microprocessor. Since the introduction of the first D20 products, the commands that are available in the 68K Monitor have changed, been added to, and enhanced to address the requirements of the newer products and their software components. This guide summarizes all of the commands that you will find in any of GE Energy Services’ products to-date. You will see in the next chapters that not all commands are available in all products. Some commands exist only for product and software development, and are not found in end-user products. In This Section This section of the document contains the following topics Topic See Page Purpose and Audience of this User’s Guide viii Support Services and Training ix GE Energy Services 68K System Monitor User's Guide SWM0023 1.00 2 General viii Full Release Purpose and Audience of this User’s Guide Job Titles While only experienced programmers should use many of the commands found in this guide, maintenance technicians and other support personnel will also find this guide useful. Experience & Abilities GE Energy Services’ customers and employees who wish to view detailed information about the software and hardware should use this guide. Prerequisites This document assumes that you are familiar with software and programming terminology and practices, and have some knowledge of both the hardware and software. What This Document Provides This guide covers the commands found in the 68K Monitors that run on these platforms: • CPM running CPM Base • D20 running D20 Base software • D20 with D20 ME running D20 Base software • D20 and D200 using CCU Base software • D20 and D200 with D20 ME processors running CCU Base • D25 Notes will show where a command or feature is unique to a specific platform. This guide is a user reference for the 68K Monitor . It describes in detail the contents and usage for each available user command. These commands are useful for testing and debugging hardware and software as they provide a means for controlling the system environment at a very low level. ! WARNING The functions provided by 68K Monitors enable you to alter and manipulate the system at a very low level. At this low level, it is easy to seriously disrupt an operational system. You must be aware of this possibility at all times. What This Document Does Not Provide. There are no procedures in this document as users should already be familiar with accessing and using GE Energy Services’ WESMAINT and monitor maintenance facilities. Document Style and Convention Rules This manual uses the Systeme International (SI) and the Microsoft Manual of Style as a basis for styles and conventions. 68K System Monitor User's Guide GE Energy Services General SWM0023-1.00 -2 Full Release ix Support Services and Training General GE Energy Services provides professional assistance in the use of all of its software and hardware products. Need Help? If you feel that the information provided in this document is unclear or in error, please contact GE Energy Services for assistance. Website http://www.gepower.com/geharrisenergy/ Unlimited access is available to a wide variety of information and company services including: • product information • training and, • technical services. Technical Support Representatives are available Monday through Friday, 8:00 a.m. to 5:00 p.m. Mountain Time. Contacting Us GE Energy Services 2728 Hopewell Place NE Calgary, Alberta Canada T1Y 7J7 Toll-Free: + 1.800.518.2303 Phone: + 1.403.214.4600 Fax: + 1.403.243.1815 email: GEH_Calgary.Support@ps.ge.com GE Energy Services 68K System Monitor User's Guide SWM0023 1.00 2 General x Full Release General SWM0023-1.00 -2 Full Release 1-1 Chapter 1: Connecting and Using the 68K Monitor Overview Connect Defined An application interface provides an input to and output from the 68K Monitor . This allows the 68K Monitor to ‘connect’ to any application or subsystem, and to any type of hardware (capable of stream or block transfers). As examples: • WESMAINT or the Login Process can connect the 68K Monitor to a serial port. • WESMAINT and the TELNET application can connect it to the TELNET session. The 68K Monitor can also be ‘connected’ to a file system to receive (read) commands from a file and send (write) responses to another file. In This Chapter This Chapter of the document contains the following topics Topic See Page Connecting to the 68K Monitor 1-2 Command Input and Response 1-3 68K Monitor Display 1-6 Error Messages 1-7 GE Energy Services 68K System Monitor User's Guide SWM0023 1.00 2 General 1-2 Full Release Connecting to the 68K Monitor One 68K Monitor At-A- Time While any application running in the system can activate the 68K Monitor , only one instance of the monitor can be active at any one time. If a second application attempts to start the 68K Monitor , it will refuse the second application’s request. 68K Monitor Prompts The prompt produced by the 68K Monitor depends on the hardware platform and the mode the device is in. As examples: Examples The table below shows examples of the prompts that you may see on various devices in different modes of operation. When this device… is operating out of… you will see this prompt… BootROM (this is known as the System Monitor ) D25S> D25 FLASH (this is known as the Application Monitor ) D25A> Service Mode D20MES> D20 ME (CCU Base) Active Mode D20MEA> CPM or D20M(++) Any Mode D20M> Terminating a 68K Monitor TELNET Session The 68K Monitor will detect a loss of connection in a TELNET session and will end the monitor session, allowing a new connection to be established. The 68K Monitor itself never terminates or initiates a TELNET session. Whatever process starts the 68K Monitor handles this functionality. Auto-Logout Timer Since only one 68K Monitor session is allowed at a time, it automatically terminates a session if no input is received for 5 minutes (default) or after a user-programmed interval. Refer to: Page 3-4, AL - Change Auto-logout Timer for details about how this timer can be changed. 68K System Monitor User's Guide GE Energy Services General SWM0023-1.00 -2 Full Release 1-3 Command Input and Response Input to the 68K Monitor Input to the 68K Monitor is read from the ‘connected’ application / subsystem. The input takes the form of user-entered commands. Command Line Limitations The 68K Monitor accepts a command line: • that is no longer than 80 characters, and • consists of no more than 16 separate words or symbols. − The definition of a word or string is one or more characters separated by one or more spaces. − Input may be either upper or lower case, except where noted. Command Format Input may be either upper- or lower-case. The format of all commands is as follows: <command_name> < parameters arguments> Where: • command_name is one of the recognized commands, and • parameter arguments are an optional list of command parameters. Common Command Syntax You must format these commands in a definite way or syntax. You must understand command syntax to understand detailed command descriptions in the following chapters. List of Characters This tables lists some of the characters used in command syntax: Character Name Description / switch identifies that the character following it affects the type of processing performed by the command [ ] square brackets any arguments listed within them are optional parameters that the command may use but does not require | OR symbol only one of several consecutive arguments listed within parenthesis “( )” is to be used ( ) multiple arguments when not separated by the OR “|” character means that if one of the arguments is used, they must all be used Continued on next page GE Energy Services 68K System Monitor User's Guide SWM0023 1.00 2 General 1-4 Full Release Command Input and Response, Continued Possible Responses By entering a command at the prompt and pressing ENTER, one of the following responses will happen. If you enter and then a recognized command it does not require special parameters the system will execute the command. a recognized command required parameters are provided the system will execute the command. a recognized command parameters are missing or invalid a reminder line showing the correct command syntax will appear, including required and optional parameters. an unrecognizable command -- a general error will be issued indicating that the command was not recognized. An Example, the EDIT Command: If you type: e [/(b | w | l | f | d)] address According to the syntax conventions: • The first field, e , must be entered as is, because it has no special characters around it. − If you press ENTER after typing just the e , the line above appears to show you the command parameter syntax. • The second field, [/(b | w | l | f | d)], because it is enclosed in [ ], is optional. − Select one of the valid switches within the parenthesis ( ) or leave it blank. • The last field , address , is required. Entering Commands The 68K Monitor allows editing of the command line by using regular keyboard input as well as a few special key combinations. Regular Keyboard Input In addition to entering any printable ASCII character onto the command line, the following characters can be used: This key… performs this function ESC deletes all current data on the command line and returns to the first character position. (except D20 base and CPM) ENTER executes any command that has been entered on the command line. BACKSPACE removes the last character from the end of the current command line and moves the cursor one character position to the left. Continued on next page 68K System Monitor User's Guide GE Energy Services General SWM0023-1.00 -2 Full Release 1-5 Command Input and Response, Continued Regular Keyboard Input (continued) Special Control Characters You can use these special control characters to perform advanced editing and screen navigation functions. Command Characters Description Abort CTRL-C returns the Monitor to the command line prompt and aborts most commands being processed. Note: a CTRL-C command does not work in a TELNET connection. Delete CTRL-D deletes the current character of the previous command line. Insert CTRL-I or TAB toggles the current mode to/from overwrite or insert. The monitor always starts in overwrite mode. Advance CTRL-A causes the monitor to copy the character from the previous command buffer reference location to the current location in the input command buffer. This character also returns the monitor to overwrite mode. Repeat CTRL-R allows editing and re-execution of the previous command by copying the previous command line from the character at the previous command reference location (up to the end of the previous command buffer) into the current input command buffer Note: D20ME and D25 have a 5-line command buffer. Execute CTRL-X copies the most previously used command to the command line and executes it. Xoff, Xon CTRL-S and CTRL-Q the combination of CTRL-S (Xoff) and CTRL-Q (Xon) stops and starts scrolling of the monitor’s display. GE Energy Services 68K System Monitor User's Guide SWM0023 1.00 2 General 1-6 Full Release 68K Monitor Display Output from the 68K Monitor The 68K Monitor’s output is a stream of ASCII characters written back to the ‘connected’ application / subsystem. The command executed determines the exact contents of the output. When encountering a system exception error, or a defined breakpoint, exception and breakpoint handling routines will generate additional output. Display Output While most output to the monitor port is a direct result of command input, some occurs asynchronously of the command input. This requires the use of two methods of output display. • The first method uses the monitor-input process , which formats the output into a common buffer and signals the output process that data is available. − All output that occurs synchronously with the input uses this method, including command data and input line display. • The second method uses exception-handling routines to display data that may or may not occur as the result of a monitor command, but cannot be expected to occur synchronously with the input. − A pSOS exchange sends this data (including unassigned exception and breakpoint data displays) to the output process. An Example: Once a breakpoint is set, the monitor cannot control when or if the system encounters the breakpoint. The exception and breakpoint display output may occur at any time, and this output has priority over monitor input process output. This may cause occasional interruption of a command or input in progress, or the lack of a prompt re-appearing after displaying the data, but does not affect these functions in any way 68K System Monitor User's Guide GE Energy Services General SWM0023-1.00 -2 Full Release 1-7 Error Messages Introduction 68K Monitor returns several general error messages resulting from input or syntax errors in the command input, or system or test failures during execution. These error messages are identified below: Message Summary The most general error is an incorrect number of arguments for the command defined. This error causes a display of the correct use of the specified function. Other possible error messages are listed below: This Message is displayed when… Application which activated the monitor has been deleted! (or suspended) a process or user requests an exit command, but the process that called 68K Monitor is suspended or deleted. Breakpoint defined! the specified address is already defined as a breakpoint, the monitor will display this message when defining a new breakpoint (DB). Breakpoint not suspended! a breakpoint was not encountered when attempting a resume (RB) or step (SB) breakpoint command. Cannot post to exchange! a send (SX) or jam (JX) exchange command encounters an error in sending the message to the specified exchange. Command aborted! the user replied NO when asked to verify a Return to BootROM (RTB) command. Command not found! the specified command is not located within 68K Monitor’s command list. FLASH invalid! a directory (DIR) command on a FLASH default database fails (i.e., no default database could be detected). Invalid ID! the monitor cannot find the specified identification, or it is incorrect. The ID can be a breakpoint number, communications port, table name, or process or exchange ID Invalid switch! the user does not specify the mode for the chosen function. No free breakpoints! the define breakpoint (DB) command is attempted when all available breakpoints are in use. Numeric input error! a numeric field contains non-numeric characters. Continued on next page GE Energy Services 68K System Monitor User's Guide SWM0023 1.00 2 General 1-8 Full Release Error Messages, Continued Message Summary (continued) This Message is displayed when… NVRAM invalid! the query RAM (QR) command specified NVRAM is but it is corrupt. Protected process! attempting to suspend (SP) a critical system process. Record error! an invalid record is detected during the download function (DL). Suspend all processes first! attempting a download without suspending all processes first. Test failed! a system error is detected. If You Find Yourself in Serious Trouble... Using the 68K Monitor it is possible to modify or change something in a device’s system that can seriously disrupt the operation of the device Use this procedure to restore the RTU to its former state, before you used the 68K Monitor facility to make changes. Step Action 1. Suspend all processes in the RTU. 2. Fill the NVRAM memory with zeros. 3. Re-download your configurations and/or Flash code. 4. Reboot the RTU. General SWM0023-1.00 -2 Full Release 2-1 Chapter 2: Command Grouping Overview Seven Groups The 68K Monitor commands are grouped into seven groups. The following pages list the commands in each of the groups, and provide a functional cross-reference to help you locate them in this guide. In This Chapter This Chapter of the document contains the following topics Topic See Page General System Commands 2-2 Diagnostic Commands 2-3 Memory Commands 2-4 Process Commands 2-5 Exchange Commands 2-6 Breakpoint Commands 2-7 Configuration Maintenance Commands 2-8 GE Energy Services 68K System Monitor User's Guide SWM0023 1.00 2 General 2-2 Full Release General System Commands Description This group of commands is essentially a list of unrelated commands that do not logically fit into the other command groups. List of Commands This list shows the General System commands, in alphabetical order: Command Description See Page AL Change Auto-logout Timer 3-4 BAUD Set Baud Rate 3-5 BOOT Boot 3-7 CF Copy File 3-15 CLS Clear Screen 3-16 DF Display File Data 3-23 DHW Display Hardware Data 3-24 DIR Directory 3-25 DL Download 3-27 ECHO Echo Toggle 3-32 EXIT Exit 3-36 FT Find Table 3-38 HE or HELP Help 3-39 IMG Display Image Information 3-41 JTF Jump to Flash 3-42 RR Report PAM Partitions 3-58 RTB Return to BootROM 3-61 RZ ZModem Download 3-64 SI System Information 3-71 UL Upload 3-81 VER Version 3-82 68K System Monitor User's Guide GE Energy Services General SWM0023-1.00 -2 Full Release 2-3 Diagnostic Commands Description You can use these diagnostic commands for debugging, performance analysis and hardware system testing. List of Commands This list shows the Diagnostic commands, in alphabetical order: Command Description See Page CACHE Control Cache 3-8 CAL Calibrate Kernel Interface 3-9 CS Check Sum 3-18 DEBUG Debug 3-22 DM Debug Mode 3-28 EL Error Log 3-33 ETH Ethernet Address 3-35 HT HDLC Test 3-40 KIM Kernel Interface Metrics 3-44 PR Profile 3-47 QR Query RAM 3-53 RT RAM Test 3-59 RTC Test CCU Real Time Clock 3-62 SA Serial Analyzer 3-66 ST Serial Test 3-74 SYSC System 3-77 TEST Invoke Test Tool 3-78 TR Trace 3-79 WINM WIN Metrics 3-84 GE Energy Services 68K System Monitor User's Guide SWM0023 1.00 2 General 2-4 Full Release Memory Commands Description Use these memory commands to identify or change the contents of memory in the system. List of Commands This list shows the Memory commands, in alphabetical order: Command Description See Page D Dump Memory 3-19 E Edit Memory 3-28 ERASE Flash Erase 3-34 F Fill Memory 3-37 M Move Memory 3-44 PRG Program Flash 3-49 ! WARNING Because executing these commands modifies the memory of your system, they can disrupt operation. Use caution before proceeding. 68K System Monitor User's Guide GE Energy Services General SWM0023-1.00 -2 Full Release 2-5 Process Commands Description Use these commands to examine and alter the state of pSOS processes. Note: Some of these functions must only used for testing and debugging during software development. List of Commands This list shows the Process commands, in alphabetical order: Command Description See Page CP Change Priority 3-16 QP Query Process 3-51 RP Resume Process 3-57 SP Suspend Process 3-72 VP Signal Process 3-83 GE Energy Services 68K System Monitor User's Guide SWM0023 1.00 2 General 2-6 Full Release Exchange Commands Description Use these commands to examine and alter pSOS exchange data in the system. Note: Use these functions primarily for testing and debugging purposes during software development. List of Commands This list shows the Exchange commands, in alphabetical order: Command Description See Page JX Jam Exchange 3-43 QX Query Exchange 3-54 RX Request Exchange 3-62 SX Send Exchange 3-76 68K System Monitor User's Guide GE Energy Services General SWM0023-1.00 -2 Full Release 2-7 Breakpoint Commands Description Use these commands with the 68K Monitor for control and display of process breakpoints in the system. The three restrictions with the definition of breakpoints are: • You must define breakpoints in code that is in RAM. − The program instruction changes to a 68000 family TRAP instruction. • You must define all program breakpoints at the beginning of an instruction. • Only define breakpoints in a process. − If the interrupt mask is non-zero when you enter the breakpoint handler, the assumption is that the calling routine is an interrupt service procedure (ISP) and breakpoints are not valid. Note: Diagnostic Commands are suspended in order to use breakpoints. List of Commands This list shows the Breakpoint commands, in alphabetical order: Command Description See Page CB Clear Breakpoint 3-9 DB Define Breakpoint 3-21 PB Print Breakpoint 3-46 RB Resume Breakpoint 3-54 SB Step Breakpoint 3-68 GE Energy Services 68K System Monitor User's Guide SWM0023 1.00 2 General 2-8 Full Release Configuration Maintenance Commands Description Use these commands to store and maintain configuration files. List of Commands This list shows the Configuration Maintenance commands, in alphabetical order: Command Description See Page CCA Change Configuration File Attributes 3-11 CCB Create Configuration Control Block 3-12 CCF Clear Configuration File 3-14 QC Query Configuration Storage Parameters 3-50 SC Select Active Configuration 3-69 68K System Monitor User's Guide GE Energy Services General SWM0023-1.00 -2 Full Release 3-1 Chapter 3: 68K Monitor Commands Overview Introduction This Chapter is divided into two sections, the first providing a cross-reference table where you can see which platform support what commands. The second section details each command, listed in alphabetical order. In This Chapter This Chapter of the document contains the following Sections and topics Topic See Page Section 1: Command / Platform Cross-Reference 3-2 Platform-Specific Commands 3-2 Section 2: Monitor Commands 3-4 GE Energy Services 68K System Monitor User's Guide SWM0023 1.00 2 General 3-2 Full Release Section 1: Command / Platform Cross-Reference Platform-Specific Commands List of Commands This table lists all of the possible 68K Monitor commands in the left column, in alphabetical order. The columns to the right show the platforms where the commands will be available for you to use. Command CPM/D20 D20ME CCU CCUME D25 AL * * * BAUD * * * BOOT * * * * * CACHE * CAL CB * * * CCA * * * CCB * * * CCF * * * CF * * CLS * CP * * CS * * * * * D * * * * * DB * * * DEBUG * DF * * DHW * DIR * * * DL * * * * * DM * * DSTAT * * E * * * * * ECHO * * EL * * * * * ERASE * * * ETH EXIT * * * * * F * * * * * FT * * * * * HE or HELP * * * * * HT * * * IMG * * * Continued on next page 68K System Monitor User's Guide GE Energy Services General SWM0023-1.00 -2 Full Release 3-3 Platform-Specific Commands, Continued List of Commands (continued) Command CPM/D20 D20ME CCU CCUME D25 JTF * JX * * * * * KIM M * * * * * PB * * * PR * * * * * PRG * QC * * * QP * * * * * QR * * * * * QX * * * * * RB * * * RP * * * * * RR * * * RT * * * * * RTB * RTC RX * * * * * RZ SA * * * * SB * * * SC * * * SET * * SI * * * SP * * * * * ST * * * * * SX * * * * * SYSC TEST * * TR UL * * * * VER * * * * * VP * * * * * WINM Note K K K K Some of the commands, such as CAL and KIM , are not checked-off for any platform. This indicates that these commands are only available when specially built engineering or debugging software is running in the device. If a product delivered to an end-user displays these commands, a mistake may have occurred. Contact GE Energy Services if in doubt. GE Energy Services 68K System Monitor User's Guide SWM0023 1.00 2 General 3-4 Full Release Section 2: Monitor Commands AL - Change Auto-logout Timer Platform o CPM o D20 D20 Base o D20 ME D20 Base þ D20/200 CCU Base þ D20/200 ME CCU Base þ D25 Description Use this command to change the monitor’s auto-logout timer duration from the default of 5 minutes. Syntax Below is usage and syntax information for this command Command Format al timout (minutes) Variables None Parameters minutes = 0 to 32767 minutes. ‘0’ disables the timer. Example Type al 15 and press ENTER. Results: The monitor will log out after 15 minutes of inactivity. Special Considerations If the timer is disabled, (set to ‘0’) the monitor can be locked- out for any other user. 68K System Monitor User's Guide GE Energy Services General SWM0023-1.00 -2 Full Release 3-5 BAUD - Set Baud Rate Platform o CPM o D20 D20 Base þ D20 ME D20 Base o D20/200 CCU Base þ D20/200 ME CCU Base þ D25 Description Use this command to change the data rate of the WESMAINT port to a user- configured value. Syntax Below is usage and syntax information for this command Command Format baud baud_rate Variables None Parameters baud_rate = the new data rate for the port, in bps. Example Type baud 4800 and press ENTER. Results: The monitor switches to communicate at 4800 bps. Special Considerations See warning below. About Changing the Baud Rate The 68K Monitor has the ability to change the communication speed of the D25 and D20 ME WESMAINT ports. This is useful when downloading large files. Example: A 1 M code file may take upwards of 40 minutes to download at 9600 bps (the default). At 38400 bps, only 10 – 15 minutes. Note: Most PCs cannot exceed 115,200 bps, and some terminal programs (Windows Terminal for example) may have other restrictions. Check the respective program's User's Guide for help. ! WARNING 1 The system will not save speed changes made using this command in NVRAM. The monitor will return to 9600 bps after a restart. If you execute this command in a D25 monitor, it will modify the data rate of both the WESMAINT and the D25MAINT ports, since they run off the same data rate generator. GE Energy Services recommends that you use this command only to speed up a serial download, and not to redefine the operational state. ! WARNING 2 Enter the baud rate correctly, as the function is capable of setting the data rate to any value. Example: Forgetting to enter the final zero when trying to change the data rate to 19200 bps would result in a rate of 1920 bps, preventing any further communication. A reboot will return the speed to the 9600 bps default. Continued on next page GE Energy Services 68K System Monitor User's Guide SWM0023 1.00 2 General 3-6 Full Release BAUD - Set Baud Rate, Continued Supported Speeds The supported data rates, in bps, are: * D25 has a maximum speed of 38400 bps. 900 3600 28200 1050 4800 * 38400 1200 7200 57600 1800 9600 115200 2000 14400 230400 2400 19200 68K System Monitor User's Guide GE Energy Services General SWM0023-1.00 -2 Full Release 3-7 BOOT - Startup - Platform þ CPM þ D20 D20 Base þ D20 ME D20 Base þ D20/200 CCU Base þ D20/200 ME CCU Base þ D25 Description Use this command to remove all defined Monitor breakpoints and then force the system to go through its lowest level start-up. This ensures that the system is properly re-initialized after testing, system manipulating, or downloading. Syntax Below is usage and syntax information for this command Command Format CPM / D20 / D20ME / CCU/ CCUME boot D25 boot [/i] [delay] Variables delay = number of milliseconds to wait before the boot is performed Parameters /i = skip all additional system processing and reset the system immediately Example Type boot and press ENTER. Results: The system responds with the normal boot-up screen. It displays a series of messages relating to hardware and software initialization. Special Considerations This command will automatically clear all breakpoints before execution. This command causes all processors in a multi-processor system to reboot. GE Energy Services 68K System Monitor User's Guide SWM0023 1.00 2 General 3-8 Full Release CACHE - Control Cache Platform o CPM o D20 D20 Base o D20 ME D20 Base o D20/200 CCU Base þ D20/200 ME CCU Base o D25 Description Use this command to enable and disable the CPU’s cache. Syntax Below is usage and syntax information for this command Command Format cache /(d | e) Variables /d = disable processor cache /e = enable processor cache Parameters None Example Type cache /d and press ENTER. The monitor disables the processor cache. Special Considerations None 68K System Monitor User's Guide GE Energy Services General SWM0023-1.00 -2 Full Release 3-9 CAL - Calibrate KI Platform o CPM o D20 D20 Base o D20 ME D20 Base o D20/200 CCU Base o D20/200 ME CCU Base o D25 Description For D200s only. Use this command to calibrate the Kernel Interface inter-processor communications. Syntax Below is usage and syntax information for this command Command Format cal (<values> | /h | /?) Variables /h = displays help /? = displays help Parameters Values = ? Example Not required Special Considerations For use by qualified programmer only. GE Energy Services 68K System Monitor User's Guide SWM0023 1.00 2 General 3-10 Full Release CB - Clear Breakpoint Platform þ CPM þ D20 D20 Base o D20 ME D20 Base o D20/200 CCU Base þ D20/200 ME CCU Base þ D25 Description Use this command to clear breakpoints that are currently set. • By specifying a breakpoint number, this command clears that breakpoint. • By not specifying a breakpoint, it clears all defined breakpoints. Breakpoints are cleared by: 1. replacing the 68000 family TRAP instruction with the original instruction, and then 2. clearing the entry in the breakpoint table Syntax Below is usage and syntax information for this command Command Format cb [break_pt#] Variables None Parameters break_pt# = breakpoint number; default is all breakpoints Example Type cb 3 and press ENTER. This clears breakpoint number 3. Results: The system displays the prompt. Special Considerations None 68K System Monitor User's Guide GE Energy Services General SWM0023-1.00 -2 Full Release 3-11 CCA - Change Configuration File Attributes Platform o CPM o D20 D20 Base o D20 ME D20 Base þ D20/200 CCU Base þ D20/200 ME CCU Base þ D25 Description Use this command to modify the configuration file attributes for a given configuration file. Overwrites the old attributes with the new attributes. Syntax Below is usage and syntax information for this command Command Format cca file_num Variables None Parameters file_num = The query configuration storage parameters command displays all existing files, giving each a numerical index. Use this index with this command to specify the affected file. Example Type cca 1 and press ENTER. see below Special Considerations When this command is invoked, the user is provided with the current attributes of the file using the characters: • ‘c’ (currently selected file) • ‘o’ (opened), and • ‘r’ (corrupt). The user is expected to enter the attributes to change by typing the character representing the attribute (‘c’, ‘o’, or ‘r’) followed by ‘+’ to add it or ‘-‘ to remove it. The same command can change any of the attributes. You can enter the same attribute multiple times, but only the last entry will take effect. You can separate each attribute by a space, but do no separate the attribute and its add/subtract character, and any other characters on the command line will result in an error. GE Energy Services 68K System Monitor User's Guide SWM0023 1.00 2 General 3-12 Full Release CCB - Create Configuration Storage Block Platform o CPM o D20 D20 Base o D20 ME D20 Base þ D20/200 CCU Base þ D20/200 ME CCU Base þ D25 Description Use this command to create the configuration storage block at a specified location or allocate it out of RAM. The amount of memory space allocated to configuration storage and other relevant parameters are also required. • The Monitor invalidates any existing storage block before creating the new one. − If requested to make the block in NVRAM, the command assumes it to be a part of a static configuration storage region and will simply use the memory as specified (base address and size). − By specifying RAM, the monitor expects the block to be temporary, and allocates memory out of normal pSOS RAM. Syntax Below is usage and syntax information for this command ! WARNING Any existing stored configurations will be lost when this command is invoked!!! Command Format ccb [/(n | v | r)] base_address total_ram response_file_size num_cfgs nvram_base Variables /n = Build configuration block in global NVRAM region using the base_address supplied. /v = Allocate the configuration block from normal RAM, ignoring the base address. /r = Reset CCB. Old CCB is cleared before new one created Parameters base_address = Address of start of configuration storage region, in hexadecimal (must be present, even if it’s just zero for RAM configuration blocks). total_ram = Total amount of NVRAM allocated to the region, in bytes. response_file_size = Size of response file, in bytes. num_cfgs = Total number of configurations to store, maximum of 2. nvram_base = Address of start of NVRAM region. Continued on next page 68K System Monitor User's Guide GE Energy Services General SWM0023-1.00 -2 Full Release 3-13 CCB - Create Configuration Storage Block, Continued Parameters (continued) Example Type ccb 600000 100000 400 2 and press ENTER. Results: The monitor creates a configuration storage control block at address 0x600000, taking the next 0x100000 bytes as the space for the configuration storage system. After allocating the size of the storage control structures and the 0x400 bytes for the response file, the command divides the remaining space into two equal slices to store configurations. Special Considerations Use this command primarily when the system first initializes, in order to set up the configuration storage space. After that, it expects to be only rarely invoked. GE Energy Services 68K System Monitor User's Guide SWM0023 1.00 2 General 3-14 Full Release CCF - Clear Configuration File Platform o CPM o D20 D20 Base o D20 ME D20 Base þ D20/200 CCU Base þ D20/200 ME CCU Base þ D25 Description Use this command to erase the specified configuration file. The command clears all contents of the file, and it clears all attribute flags as well. Syntax Below is usage and syntax information for this command Command Format ccf file_num Variables None Parameters file_num = The query configuration storage parameters command displays all existing files, giving each a numerical index. This index specifies the file that you wish cleared. Example Type ccf 1 and press ENTER. The monitor erases the contents of stored configuration 1. Special Considerations Used only when multiple storage regions are defined 68K System Monitor User's Guide GE Energy Services General SWM0023-1.00 -2 Full Release 3-15 CF - Copy File Platform o CPM o D20 D20 Base o D20 ME D20 Base þ D20/200 CCU Base o D20/200 ME CCU Base þ D25 Description Use this command to copy file information from one file to another. Primarily, use the command to transfer files containing configuration, application FLASH and DSP FLASH program data into their destination regions. Also, use it to copy any one file to another, depending on the support for copying provided by the File System Driver that owns the files. Syntax Below is usage and syntax information for this command Command Format cf source_file [destination_file] Variables None Parameters source_file = The name of the file containing the source data. This is always required, and is the full path name of the file. If the operation is transferring configuration or FLASH program information (DSP or application), then only the source name is required. destination_file = The name of the file into which the source file data is to be copied. If you intend to copy configuration or FLASH program information (DSP or application) into its destination region, this name is optional and unnecessary Example Type cf flash.zlb and press ENTER. Results: The monitor copies the file flash.zlb into Flash EPROM. Special Considerations Once invoking this function, it may take some time for the command to write the file into its destination; especially if it consists of compressed configuration or FLASH program information (DSP or application). GE Energy Services 68K System Monitor User's Guide SWM0023 1.00 2 General 3-16 Full Release CLS - Clear Screen Platform o CPM o D20 D20 Base o D20 ME D20 Base o D20/200 CCU Base o D20/200 ME CCU Base þ D25 Description Use this command to clear the monitor’s screen. Syntax Below is usage and syntax information for this command Command Format cls Variables None Parameters None Example None Required. Special Considerations None 68K System Monitor User's Guide GE Energy Services General SWM0023-1.00 -2 Full Release 3-17 CP - Change Priority Platform o CPM o D20 D20 Base o D20 ME D20 Base o D20/200 CCU Base þ D20/200 ME CCU Base þ D25 Description Use this command to change the current priority of an existing process. Syntax Below is usage and syntax information for this command Command Format cp (/h | ((pid | PName) (delta | abs))) Variables /h = display help Parameters pid = PID number PName = name of the process delta = the priority change to be made. A negative value reduces priority. A positive value adds priority. abs = the final priority of process after change in Hex Example Type cp WES0 +20 and press ENTER. Results: The monitor increases the priority of process WES0 by (delta) 0x20. Note: Process/Task names, like WES0, are case-sensitive. Special Considerations If you use this command to change the priority of the IDLE process, the system will reboot. GE Energy Services 68K System Monitor User's Guide SWM0023 1.00 2 General 3-18 Full Release CS - Check Sum Platform þ CPM þ D20 D20 Base þ D20 ME D20 Base þ D20/200 CCU Base þ D20/200 ME CCU Base þ D25 Description Use this command to perform a checksum or 32-bit CRC of either the boot code area, NVRAM area, or application code area. Syntax Below is usage and syntax information for this command Command Format CPM / D20 / D25: cs / (b | n | p) CCU / CCUME: cs / (b | n | p | g) Variables /b = boot code area /n = NVRAM area /p = application code area /g = global NVRAM area Parameters None Example Type cs /g and press ENTER; this performs a check sum of the global NVRAM area. Results: The system responds with the calculated and expected checksums of the specified area, and the message Checksum is ___ and should be ___. A new prompt appears. Special Considerations Performing cs on flash memory will require 5 to 10 minutes. 68K System Monitor User's Guide GE Energy Services General SWM0023-1.00 -2 Full Release 3-19 D - Dump Memory Platform þ CPM þ D20 D20 Base þ D20 ME D20 Base þ D20/200 CCU Base þ D20/200 ME CCU Base þ D25 Description Use this command to display memory contents as bytes, words, long words, floating- point numbers, or double-precision numbers. Each line of output is formatted as: at the left margin: − starting address of the memory, hexadecimal. then: − 16 bytes (octets) of data grouped as: • bytes − hexadecimal format • words − hexadecimal format • long words − hexadecimal format • floating-point numbers − scientific format • double-precision numbers − scientific format then: − 16 ASCII characters representing the same memory values. If an octet does not have a printable ASCII representation, the monitor will print a dot instead. Syntax Below is usage and syntax information for this command Command Format d [/(b | w | l | f | d)] beg_addr [end_addr] Variables /b = bytes (octets), the default mode /w = words /l = long words /f = floating-point numbers /d = double-precision numbers Parameters By not entering any parameters, the command requests a dump from the last user-entered memory dump location. The dump is in the previously specified format (if any) and dumps for 80 bytes. beg_addr = first address to display, in hexadecimal. end_addr = address up to which to display, in hexadecimal; the default is beg_addr plus 80 hexadecimal. Continued on next page GE Energy Services 68K System Monitor User's Guide SWM0023 1.00 2 General 3-20 Full Release D - Dump Memory, Continued Syntax (continued) Example Type d /w f024 and press ENTER. Results: The system displays the specified data (eight lines consisting of address, eight hexadecimal words, and 16 ASCII characters, starting at hexadecimal address F024), then displays the prompt. Type d and press ENTER. Results: The system displays the next eight lines starting at hexadecimal address F024+80=F0A4, then displays the prompt. Special Considerations • An attempt to display non-existent memory results in a bus error. • If this is the first dump, not specifying any parameters will return an error. 68K System Monitor User's Guide GE Energy Services General SWM0023-1.00 -2 Full Release 3-21 DB - Define Breakpoint Platform þ CPM þ D20 D20 Base o D20 ME D20 Base o D20/200 CCU Base þ D20/200 ME CCU Base þ D25 Description Use this command to activate a breakpoint in a section of code located within RAM. At the specified address, the command saves 68000 family instruction in the breakpoint table and replaces it with a TRAP instruction. When a process reaches the TRAP instruction, it traps into a breakpoint handling routine, which displays a message indicating that it encountered a breakpoint. The 68K Monitor allows up to ten active breakpoints. Syntax Below is usage and syntax information for this command Command Format db address [#loops] Variables None Parameters address = hexadecimal address for the breakpoint. #loops = number of times to execute the specified address (in decimal) before stopping; default is zero Example Type db 103648 and press ENTER. This defines a breakpoint at hexadecimal address 103648, which stops before the first execution of the instruction at that address. Results: The system responds with the breakpoint number assigned to this breakpoint and the prompt. Each time it encounters the breakpoint, the system displays the breakpoint number, loop count, and register values. If the loop count is greater than zero, it is decremented. Otherwise, the process is suspended. Special Considerations You may define only one breakpoint at a single address, to a maximum of ten breakpoints per system. An attempt to define a breakpoint in read only or non-existent memory results in a bus error. GE Energy Services 68K System Monitor User's Guide SWM0023 1.00 2 General 3-22 Full Release DEBUG - Debug Mode Platform o CPM o D20 D20 Base o D20 ME D20 Base o D20/200 CCU Base o D20/200 ME CCU Base þ D25 Description Use this command to put the D25 into Debug Mode. This mode disables certain checks in the system so that it will ignore small system violations during debugging sessions (such as allowing the writing of FLASH code to RAM during a download). In this mode, you can make making changes to the base address and size of the SRAM, NVRAM and FLASH regions in the NVRAM configuration header. Syntax Below is usage and syntax information for this command Command Format DEBUG Variables None Parameters None Example Type DEBUG and press ENTER. Results: The output displays the current debug state. The user receives the following prompt: Do you wish to update the NVRAM header? (y/n) Any reply other than ‘y’ aborts the rest of the command. Otherwise, the command prompts you to enter new values for the FLASH, SRAM, and NVRAM base address and size. Entering a zero indicates that the item is to remain unchanged. Once the new data has been entered, you are prompted: Is this data accurate? (Y/N) Any response other than ‘y’ will cause the monitor to re-issue the prompts for the FLASH, SRAM, and NVRAM base address and size. Pressing CNTRL-C will abort the command. If the user responds ‘y’, the command writes new data to the NVRAM header and a new NVRAM header CRC is calculated and stored. Special Considerations The debug command is a toggle, turning the debug mode ON if it is OFF, and OFF if it is ON. Enabling the Debug Mode degrades the performance of the system and may cause certain CPU intensive commands to activate the watchdog and reset the system. 68K System Monitor User's Guide GE Energy Services General SWM0023-1.00 -2 Full Release 3-23 DF - Display File Data Platform o CPM o D20 D20 Base o D20 ME D20 Base þ D20/200 CCU Base o D20/200 ME CCU Base þ D25 Description Use this command to display the contents of any file in memory in text or binary format. The default is binary format, which mimics the dump command by displaying the binary values first, then the printable ASCII values afterward. You may view any file recognized by the Installable File System. Syntax Below is usage and syntax information for this command Command Format df [/(b | t)] filename Variables /b = Display contents in binary format (default). /t = Display contents as text. Parameters filename = The full path name of the file to be displayed. Example Type df /b config.bin and press ENTER. Results: The monitor displays the contents of the file config.bin in a manner similar to the dump command. Special Considerations By not providing any other switch, the command selects the binary dump format, and is identical to the dump memory command format except that it lacks the address prefix. GE Energy Services 68K System Monitor User's Guide SWM0023 1.00 2 General 3-24 Full Release DHW - Display Hardware Data Platform o CPM o D20 D20 Base o D20 ME D20 Base o D20/200 CCU Base o D20/200 ME CCU Base þ D25 Description Use this command to display information on the hardware configuration of the D25. The provided information consists of: • size and base address of all memory regions • DSP and XCOM type • state of the auxiliary output and sysfail signal, and • EPLD and PCB revision numbers. Syntax Below is usage and syntax information for this command Command Format dhw Variables None Parameters None Example Type dhw and press ENTER Results: A comprehensive list of hardware and memory information is displayed. Special Considerations None 68K System Monitor User's Guide GE Energy Services General SWM0023-1.00 -2 Full Release 3-25 DIR - Directory Platform o CPM o D20 D20 Base o D20 ME D20 Base þ D20/200 CCU Base þ D20/200 ME CCU Base þ D25 Description Use this command to display a directory of the database tables residing in a specified memory type. Database table information consists of: name - table name address - the absolute table memory address records - the number of valid records in the table record size - the size, in bytes of each record Syntax Below is usage and syntax information for this command Command Format D25: dir [/(n | p)] CCU / CCUME: dir [/(l | g | e)] Variables /l = local NVRAM database tables (default) /g = global NVRAM database tables /e = EPROM/Flash default configuration database tables /n = D25 NVRAM /p = D25 Flash Parameters None Example Type dir /n and press ENTER. Results: The monitor displays the above information for all NVRAM database tables. At the end of every full screen, the monitor prompts “--More--” , and will continue when any key is pressed. Continued on next page GE Energy Services 68K System Monitor User's Guide SWM0023 1.00 2 General 3-26 Full Release DIR - Directory, Continued Syntax (continued) Special Considerations Global database tables only exist if a multi-node CCU is present. EPROM database tables form the default configuration for the CCU. They are optional and may not have been included in the CCU. If any type of database is unavailable, the DIR command will return an error message. 68K System Monitor User's Guide GE Energy Services General SWM0023-1.00 -2 Full Release 3-27 DL - Download Platform þ CPM þ D20 D20 Base þ D20 ME D20 Base þ D20/200 CCU Base þ D20/200 ME CCU Base þ D25 Description Use this command to download data (typically configuration files (all platforms) or D25 and CCUME application (FLASH) code). Note: When downloading application code files, this command must be used only when executing from the BootROM. This will be indicated by the D25A> , or the D20MEA> prompts for the D25 or D20ME-based systems, respectively. The Monitor accepts S1, S2 and S3 data records, and S7, S8 and S9 end records, and optional S0 comment records in the downloaded file. The monitor rejects all other types of records. Once the command verifies the checksum within the record, the contents of data records (S1, S2 or S3) are stored in memory. When it receives an S7, S8 or S9 end record, the DOWNLOAD command returns control to the Monitor’s command line. Syntax Below is usage and syntax information for this command Command Format D25 / CCUME: dl [/o offset] CPM / D20 / CCU: dl Variables offset = the offset at which to download Parameters /o = specifies that an offset follows Example Type dl and press ENTER. Results: This prepares the monitor to receive Motorola S- records over the serial port. The monitor does not echo any further until it encounters an end record (the prompt returns at this point) or a format or record checksum error (this returns an error message before returning the prompt). Special Considerations Each S-record, terminated by a carriage return or line feed, cannot exceed 80 decimal bytes in length. Application code download works ONLY when: • The BootROM code is being executed AND • The FLASH region has been erased. ! WARNING Executing this command modifies the memory of the system, and can cause operational disruption. Use caution before proceeding. GE Energy Services 68K System Monitor User's Guide SWM0023 1.00 2 General 3-28 Full Release DM - Debug Mode Platform þ CPM þ D20 D20 Base þ D20 ME D20 Base o D20/200 CCU Base o D20/200 ME CCU Base o D25 Description Use this command to enable or disable product-specific debugging modes. • For the 68020, (D20M) and 68EC030 (D20 ME) it disables the on-chip instruction cache. • For the 68332, (CPM) it enables show cycles. When enabled, both of these debug mode instructions allow external bus monitoring. Syntax Below is usage and syntax information for this command Command Format dm /(d | e) Variables /d = disable debug mode (Enable cache or disable show cycles) /e = enable debug mode (disable cache or enable show cycles) Parameters None. Example Type dm /e and press enter. Results: This command disables the 68020 or 68EC030 on- chip instruction cache or, enables show cycles for the 68332. The system returns the prompt upon completion of this instruction. Special Considerations Enabling the Debug Mode degrades the performance of the system and may cause certain CPU intensive commands to activate the watchdog and reset the system. 68K System Monitor User's Guide GE Energy Services General SWM0023-1.00 -2 Full Release 3-29 DSTAT - Decompression Status Platform o CPM o D20 D20 Base o D20 ME D20 Base þ D20/200 CCU Base o D20/200 ME CCU Base þ D25 Description Use this command to view status of file copy command progress and success. Syntax Below is usage and syntax information for this command Command Format dstat [l | m] Variables l = leave immediately (default) m = maintain connection until process complete, showing progress while connected. Parameters None Example Not required Special Considerations None GE Energy Services 68K System Monitor User's Guide SWM0023 1.00 2 General 3-30 Full Release E - Edit Memory Platform þ CPM þ D20 D20 Base þ D20 ME D20 Base þ D20/200 CCU Base þ D20/200 ME CCU Base þ D25 Use this command to display and modify memory locations. The command does not verify memory contents after they are stored. After entering the command, it prompts you with the current contents of a memory location. The different display and edit formats supported are: • bytes • words • floating-point numbers • scientific format • double-precision numbers − hexadecimal format − hexadecimal format − hexadecimal format − scientific format − scientific format Description When the contents of the memory location appear, type: • a new value to store at the location • a hyphen (-) to back up one location • a plus sign (+) or the ENTER key to move forward one location (CCU / D25 only) • a period (.) to exit this function Scientific values must subscribe to the following format: [ ± ] mantissa [e [ ± ] exponent] The mantissa can contain a decimal point. This command differentiates between a negative number and a hyphen. Syntax Below is usage and syntax information for this command Command Format CPM / D20: e [/(b | w | l | f | d)] address CCU / CCUME / D25: e [/(b | w | l | f | d)] [/x] address Variables /b = bytes (octets), the default mode /w = words /l = long words /f = floating-point numbers /d = double-precision numbers /x = do not display existing contents of memory location being edited Continued on next page 68K System Monitor User's Guide GE Energy Services General SWM0023-1.00 -2 Full Release 3-31 E - Edit Memory, Continued Syntax (continued) Parameters address = address to edit in hexadecimal notation Example Type e /l 200000 and press ENTER. This indicates that you are editing RAM memory, starting at address 200000 hexadecimal in long word format. Results: The system continues to display the current address location and data at that location in hexadecimal format, until you use a period (.) to return the monitor prompt. Special Considerations • An attempt to display non-existent memory or modify EPROM memory results in a bus error. • You may modify systems with FLASH EPROM such as the D25 and CCUME using this command. GE Energy Services 68K System Monitor User's Guide SWM0023 1.00 2 General 3-32 Full Release ECHO - Echo Toggle Platform o CPM o D20 D20 Base o D20 ME D20 Base o D20/200 CCU Base þ D20/200 ME CCU Base þ D25 Description Use this command to turn command line echoing on and off. It only affects the 68K Monitor’s echoing of user-entered keystrokes, and not the results of any commands. Syntax Below is usage and syntax information for this command Command Format echo [(on | off)] Variables None Parameters on = turns command line echoing on off = turns command line echoing off. Example Type echo off and press ENTER. Results: The monitor no longer displays your keystrokes as you type. Special Considerations None 68K System Monitor User's Guide GE Energy Services General SWM0023-1.00 -2 Full Release 3-33 EL - Error Log Platform þ CPM þ D20 D20 Base þ D20 ME D20 Base þ D20/200 CCU Base þ D20/200 ME CCU Base þ D25 Description Use this command to display and delete system error log entries stored in NVRAM for a single or multi-processor system. The display command also presents the current system state, and any significant low- level system errors which occur. The delete function deletes system error log entries from memory, and clears the disabled state if the system is in a disabled state. Syntax Below is usage and syntax information for this command Command Format CPM / D20 el / (p | r) D20ME / CCU / D25 el / (p | r | f) Variables /p = print the error log entries /r = reset (delete) the error log entries /f = fix an error log that contains an infinite loop Parameters None Example Type el /p and press ENTER. Results: This command displays the error log entries maintained by the system and the system state. The system returns the prompt when it completes this instruction Special Considerations None GE Energy Services 68K System Monitor User's Guide SWM0023 1.00 2 General 3-34 Full Release ERASE - Flash Erase Platform o CPM o D20 D20 Base þ D20 ME D20 Base o D20/200 CCU Base þ D20/200 ME CCU Base þ D25 Description Note: this command is available only when executing from the BootROM. This will be indicated by the D25A> , or the D20MEA> prompts for the D25 or D20ME-based systems, respectively. Use this command to perform an erase of the Flash memory region, resetting all bytes in Flash to 0xFF in preparation for application data download. Syntax Below is usage and syntax information for this command Command Format D25: erase [/d /y] D20 ME / CCUME: erase [/y] Variables None Parameters /d = erase DSP Flash /y = disable the verification prompts Example Type erase and press ENTER. Results: If you confirm the erase prompt, the command erases the Flash EPROM. Special Considerations The command prompt will return if Flash is already clear when the erase command is invoked. Otherwise, the command prompts the user to confirm the Flash erase. If you enter any response other than “y”, the command aborts the erase. ! WARNING Executing this command modifies RTU memory and will cause operational disruption (specifically by destroying all Flash application code). Do not use this command unless you are prepared to perform a code download procedure. Use caution before proceeding. 68K System Monitor User's Guide GE Energy Services General SWM0023-1.00 -2 Full Release 3-35 ETH - Ethernet Address Platform o CPM o D20 D20 Base o D20 ME D20 Base o D20/200 CCU Base o D20/200 ME CCU Base o D25 Description Use this command to change the Ethernet address of a D25’s hardware interfaces. Syntax Below is usage and syntax information for this command Command Format eth /(d | u) [b1 b2 b3 b4 b5 b6] Variables /d = display address /u = update address Parameters [b1 b2 b3 b4 b5 b6] = 6 byte Ethernet address Example Nor required Special Considerations Do not use unless qualified. Address change is permanent, and will stay in D25 XCOM hardware even if moved to another D25. GE Energy Services 68K System Monitor User's Guide SWM0023 1.00 2 General 3-36 Full Release EXIT - Exit Platform þ CPM þ D20 D20 Base þ D20 ME D20 Base þ D20/200 CCU Base þ D20/200 ME CCU Base þ D25 Description Use this command to perform a limited clean up of the 68K Monitor , and return to the calling routine (such as WESMAINT) if it has not been suspended. Syntax Below is usage and syntax information for this command Command Format exit Variables None Parameters None Example Type exit and press ENTER. Results: The monitor returns control to the calling routine. Special Considerations The task that started the 68K Monitor must still exist and be running (i.e. not suspended). This command automatically clears all active breakpoints but does not perform any other clean-up operations. This means that if you enable debug mode, if something has suspended processes, or any other system alterations made, they will remain in effect even after exiting the monitor. 68K System Monitor User's Guide GE Energy Services General SWM0023-1.00 -2 Full Release 3-37 F - Fill Memory Platform þ CPM þ D20 D20 Base þ D20 ME D20 Base þ D20/200 CCU Base þ D20/200 ME CCU Base þ D25 Description Use this command to repeatedly write a value to a specified region of memory. The command requires three numerical arguments in hexadecimal format: • first is the starting address of the region to fill • second is the ending address of the region • third is the value to write to the memory region The fill value may be a byte (octet), a word, or a long word, depending on the mode selected by the switch. Syntax Below is usage and syntax information for this command Command Format f [/(b | w | l)] beg_addr end_addr value Variables /b = bytes (octets), the default mode /w = words /l = long words Parameters beg_addr = start address of region in hexadecimal end_addr = address to fill up to in hexadecimal value = value to put in region in hexadecimal Example Type f /w 200000 200400 F034 and press ENTER. Results: This fills the RAM memory from hexadecimal address 200000 to 200400 with words of F034 hexadecimal. The system displays the prompt when it completes this instruction. Special Considerations • An attempt to fill EPROM memory results in a bus error. • You can modify systems with FLASH EPROM such as the D25 and CCUME using this command. GE Energy Services 68K System Monitor User's Guide SWM0023 1.00 2 General 3-38 Full Release FT - Find Table Platform þ CPM þ D20 D20 Base þ D20 ME D20 Base þ D20/200 CCU Base þ D20/200 ME CCU Base þ D25 Description Use this command to search available Database Manager resources to obtain the address and number of records in a database table within the database management system. Syntax Below is usage and syntax information for this command Command Format ft table_name Variables None Parameters table_name = name of the database table to locate (not case-sensitive). Example Type ft p097cpro and press ENTER. to locate the P097CPRO table in the database. Results: The monitor displays the hexadecimal format address and decimal format number of records in the specified table. It displays zeros for the address and number of records if it does not find the table. Special Considerations This command may not function if NVRAM is corrupted. This is because the NVRAM header inside the D25 contains the location of the root table of the Database Manager and all of the table identification blocks. 68K System Monitor User's Guide GE Energy Services General SWM0023-1.00 -2 Full Release 3-39 HE or HELP - Help Platform þ CPM þ D20 D20 Base þ D20 ME D20 Base þ D20/200 CCU Base þ D20/200 ME CCU Base þ D25 Description Use this command to display a list of all available monitor commands on the screen, or a description and usage for a given specific command. Syntax Below is usage and syntax information for this command Command Format CCU / CCUME / D25 he or help [command] CPM / D20 help [command] Variables None Parameters command = name of the specific command you wish to obtain information about. Example Type help and press ENTER. Results: System displays a list of available monitor commands and returns either to the prompt, or will prompt you (with ---More--- ) to press any character to display the rest of the list. Special Considerations None GE Energy Services 68K System Monitor User's Guide SWM0023 1.00 2 General 3-40 Full Release HT - HDLC Test Platform o CPM þ D20 D20 Base þ D20 ME D20 Base o D20/200 CCU Base þ D20/200 ME CCU Base o D25 Description Use this command to transmit specific application messages over the HDLC communication link. Note: Because you must assemble these messages by hand, you can not use the command effectively unless you know the protocol used by the D.20 application. Syntax Below is usage and syntax information for this command Command Format ht /(c | m | r | s | w) Variables /c = configure the link parameters /m = define the application message /r = read (monitor) the link /s = display configuration status /w = send an application message Parameters None Example None required Special Considerations This command is not available on the CPM. This command is not available if the D.20 (B003) application is active. 68K System Monitor User's Guide GE Energy Services General SWM0023-1.00 -2 Full Release 3-41 IMG - Display Image Information Platform o CPM o D20 D20 Base þ D20 ME D20 Base o D20/200 CCU Base þ D20/200 ME CCU Base þ D25 Description Use this command to display information on the BootROM, FLASH, and NVRAM configuration images. The information consists of: For the BootROM and FLASH images, a description string and a part number; For the NVRAM configuration, the static CRC and configuration version. Note: If any of this information is not available, the monitor will display a message indicating this in place of the expected information. Because the IMG command only displays information entered into the MODULE.MAK file used in the SDS system, any omissions or mistakes in the MAK file will be reflected in the output of this command. Syntax Below is usage and syntax information for this command Command Format img Variables None Parameters None Example Type img and press ENTER. Results: The monitor displays information on the FLASH, BootROM, and configuration images currently active in the system. Special Considerations None GE Energy Services 68K System Monitor User's Guide SWM0023 1.00 2 General 3-42 Full Release JTF - Jump To Flash Platform o CPM o D20 D20 Base o D20 ME D20 Base o D20/200 CCU Base o D20/200 ME CCU Base þ D25 Description Use this command to place the D25 in Active Mode. The system stops execution out of the BootROM region, and it activates the FLASH operating system. Syntax Below is usage and syntax information for this command Command Format jtf Variables None Parameters None Example Type jtf and press ENTER. Type yes to confirm. Results: The system returns to FLASH operation mode. Special Considerations The system must be operating out of BootROM to use this command. The system halts and deletes all applications currently executing on the RTU when activating the FLASH operating system. ! WARNING This command causes the D25 to shift into active mode immediately, without performing any checks on FLASH. Be sure that your FLASH region contains valid application data before invoking this command. 68K System Monitor User's Guide GE Energy Services General SWM0023-1.00 -2 Full Release 3-43 JX - Jam Exchange Platform þ CPM þ D20 D20 Base þ D20 ME D20 Base þ D20/200 CCU Base þ D20/200 ME CCU Base þ D25 Description Use this command to force a message to the beginning of the message queue at one or more exchanges. Syntax Below is usage and syntax information for this command Command Format CPM / D20 / D25: jx (xid | name) m2 m3 m4 m5 CCU / CCUME: jx (xid | gxid | name) m2 m3 m4 m5 [/g] Variables /g = Allows the message to be jammed into a queue in a different node Parameters xid = pSOS exchange ID (in hexadecimal); send message to a specific exchange. gxid = global exchange ID (in hexadecimal); send message to a specific exchange. name = case-sensitive exchange name. The command supports the new exchange naming convention. If you enter an entire name, the monitor sends the message to that exchange. If you enter the first few characters, the command attempts pattern matching. It sends the message to one or more exchanges depending on the number of matches. m2 - m5 = first through fourth long words in the body of the message, in hexadecimal. Example Type jx 304540 1 2 3 4 and press ENTER. This sends a message to an exchange identified as 304540. The command sets the first two reserved messages to 0. Results: Unless it encounters an error, the system displays the prompt. In the case of an error, it displays an error message before the prompt. Special Considerations You must only use this command in a testing or debugging context. If you send an indiscriminate message to an exchange, you cannot predict the results. GE Energy Services 68K System Monitor User's Guide SWM0023 1.00 2 General 3-44 Full Release KIM - KI Metrics Platform o CPM o D20 D20 Base o D20 ME D20 Base o D20/200 CCU Base o D20/200 ME CCU Base o D25 Description D200 only. Use this command to view the Kernel Interface Metrics. Syntax Below is usage and syntax information for this command Command Format kim [/r] (node_number | 0) Variables /r = reset Parameters node_number = processor number of D200 0 = all processors Example Type kim 3 and press ENTER Results: Displays the metrics of node 3 (3 rd processor) Special Considerations Used during debug process only. Requires special code to use 68K System Monitor User's Guide GE Energy Services General SWM0023-1.00 -2 Full Release 3-45 M - Move Memory Platform þ CPM þ D20 D20 Base þ D20 ME D20 Base þ D20/200 CCU Base þ D20/200 ME CCU Base þ D25 Description Use this command to copy memory from one memory region to a writeable memory region. It requires three hexadecimal quantities, which define the: • source address • destination address, and • number of bytes to transfer Syntax Below is usage and syntax information for this command Command Format m from_addr to_addr num_bytes Variables None Parameters from_addr = start address of the source region in hexadecimal to_addr = start address of the destination in hexadecimal num_bytes = size in bytes (octets), hexadecimal, of the region to move Example Type m 200000 200400 200 and press ENTER. Results: This copies the RAM memory region 200000 up to 200200 to the region 200400 up to 200600. The system displays the prompt when it completes this instruction. Special Considerations An attempt to move to EPROM or non-existent memory will result in a bus error. You can modify systems with FLASH EPROM such as the D25 and CCUME using this command. GE Energy Services 68K System Monitor User's Guide SWM0023 1.00 2 General 3-46 Full Release PB - Print Breakpoint Platform þ CPM þ D20 D20 Base o D20 ME D20 Base o D20/200 CCU Base þ D20/200 ME CCU Base þ D25 Description Use this command to display breakpoint information about any or all-active breakpoints in the system. While the system suspends a process at a breakpoint, this instruction causes the display of the suspended process ID and the register values when it encounters the breakpoint. These values differ from those printed with the query process command, as the latter prints the values at the time of the last process swap. Syntax Below is usage and syntax information for this command Command Format pb [break_pt#] Variables None Parameters break_pt# = breakpoint number as returned with the defined breakpoint command. Example Type pb and press ENTER. Results: If the system encounters a breakpoint, it responds with a list of all active breakpoints in the system and, the process ID, loop count, and register values, in hexadecimal. It then displays the prompt without affecting the state of any breakpoint. Special Considerations None 68K System Monitor User's Guide GE Energy Services General SWM0023-1.00 -2 Full Release 3-47 PR - Profile Platform þ CPM þ D20 D20 Base þ D20 ME D20 Base þ D20/200 CCU Base þ D20/200 ME CCU Base þ D25 Description Use this command to display run-time statistics of all processes in the system, including: • the number of times the process was swapped in • the number of system real-time clock ticks occurring during its run periods • the average number of ticks (in tenths of a tick) per run (average) • the CPU usage (in 10 ths of percent) of the process • the maximum period between watchdog process operations. Note: Each clock tick is one millisecond. Syntax Below is usage and syntax information for this command Command Format CPM / D20M pr / (p | r) CCU / CCUME / D25 pr / (p | r | t) Variables /p = print the process profile /r = reset process profile counts /t = print the process profile in the sequence of CPU usage percentage Parameters None Example Type pr /r and press ENTER. Results: The command resets the counts associated with process profiling and watchdog run period. The system displays any specified data and then returns the prompt Continued on next page GE Energy Services 68K System Monitor User's Guide SWM0023 1.00 2 General 3-48 Full Release PR - Profile, Continued Syntax (continued) Special Considerations Important points to note: • Data format of the output run count and run ticks are decimal integral values. − Ticks per run are tenths of milliseconds and CPU use are tenths of a percent decimal. − The system represents figures in decimal notation. • This profiler does not account for interrupt service CPU usage. • Roll-over of the profiler's counts occurs after some time more than 14 days. − The exact roll-over time depends on the running applications, and may vary greatly between sites and remotes. 68K System Monitor User's Guide GE Energy Services General SWM0023-1.00 -2 Full Release 3-49 PRG - Program Flash Platform o CPM o D20 D20 Base o D20 ME D20 Base o D20/200 CCU Base þ D20/200 ME CCU Base o D25 Description Use this command to program a FLASH memory. Syntax Below is usage and syntax information for this command Command Format prg [/(b | w | l)] address data Variables /b = bytes (octets), the default mode /w = words /l = long words Parameters address = address at which to store the data, in hexadecimal data = the data to store Example Not Required Special Considerations Use with great care. Command will change contents of Flash memory without updating checksum. GE Energy Services 68K System Monitor User's Guide SWM0023 1.00 2 General 3-50 Full Release QC - Query Configuration Storage Parameters Platform o CPM o D20 D20 Base o D20 ME D20 Base þ D20/200 CCU Base þ D20/200 ME CCU Base þ D25 Description Use this command to display the contents of the configuration storage block, providing information such as: • how many configurations are stored in the system • how much memory is allocated to configuration storage, and • the creation time and date of the stored configurations. Note K K K K The number used to identify each file in this display is the file index. The system uses this number to identify the file affected by the clear configuration file, change configuration file attributes, and select active configuration commands. Syntax Below is usage and syntax information for this command Command Format qc Variables None Parameters None Example Type qc and press ENTER. Results: The monitor displays the information about existing configuration storage. Special Considerations None 68K System Monitor User's Guide GE Energy Services General SWM0023-1.00 -2 Full Release 3-51 QP - Query Process Platform þ CPM þ D20 D20 Base þ D20 ME D20 Base þ D20/200 CCU Base þ D20/200 ME CCU Base þ D25 Description Use this command to display the: • general status of all currently active processes • general status of specific processes, or • detailed information about one currently active process. Syntax Below is usage and syntax information for this command Command Format CPM / D20 / D25: qp [(pid | name)] CCU / CCUME: qp [(pid | gpid | name)] Variables None Parameters (none) = display general status information for all processes. pid = pSOS process ID (in hexadecimal); display detailed information for a specific process. gpid = global pSOS process ID (in hexadecimal); display detailed information for a specific process. name = case-sensitive process name. Supports the new process naming convention. To display an entire name, enter detailed information for that process. If you enter the first few characters, the command attempts pattern matching. The monitor displays general or detailed information depending on the number of matches. Example Type qp and press ENTER. Results: The system displays process information about all active processes, and then returns to the prompt. Continued on next page GE Energy Services 68K System Monitor User's Guide SWM0023 1.00 2 General 3-52 Full Release QP - Query Process, Continued Syntax (continued) Special Considerations All numeric data displayed is in hexadecimal notation. Information Details The response to all QP commands will include: • process name • process ID • group ID • priority • current run state The response to QP commands that specify processes will include: • received signals • time slice • run ticks • run count • owned memory segments • register values at the time of the last swap Current Run State This table lists the states that the processes may be in at any time: In this state… the process… Await is spawned but not activated. Vwait is waiting for a pSOS signal. Xwait is waiting for a message from another process to arrive at an exchange. Paused has sent a ‘pause’ request to processor. Suspended has been spawned and activated, but is not running. • This state may be a normal condition, or may indicate a fatal configuration or system error. Check the WESMAINT Logger to verify. Multi-Processor Displays For a multi-processor system, this command displays: • a specific global process' summary consisting of its node and local pid, or • the process summary of all local processes to the node, and all global processes in the system. 68K System Monitor User's Guide GE Energy Services General SWM0023-1.00 -2 Full Release 3-53 QR - Query RAM Platform þ CPM þ D20 D20 Base þ D20 ME D20 Base þ D20/200 CCU Base þ D20/200 ME CCU Base þ D25 Description Use this command to examine the RAM allocation and use for either static RAM or NVRAM. The Command displays: • the memory block sizes • whether they are used, and • the total size of available free memory. The command also queries the global memory RAM if in a multi-processor system. Syntax Below is usage and syntax information for this command Command Format CPM / D20 / D25: qr / (v | n) CCU / CCUME: qr / (v | n | gv | gn) Variables /v = volatile (static) RAM /n = non-volatile RAM (NVRAM) /gv = global volatile (static) RAM /gn = global non-volatile RAM (NVRAM) Parameters None Example Type qr /gn and press ENTER. Results: This displays the allocation and available free global NVRAM. The system displays the address and size of each block in hexadecimal, the total free memory, and number of free blocks in decimal notation before it returns to the prompt. Special Considerations Non-volatile memory cannot be queried if the NVRAM is corrupt GE Energy Services 68K System Monitor User's Guide SWM0023 1.00 2 General 3-54 Full Release QX - Query Exchange Platform þ CPM þ D20 D20 Base þ D20 ME D20 Base þ D20/200 CCU Base þ D20/200 ME CCU Base þ D25 Description Use this command to display information on system exchanges. • If you request information on more than one exchange, then the output is in a list format. Each line contains an exchange name and ID, and the number of processes and messages queued. • If you request information on all exchanges, the monitor derives and displays the number of free exchange control blocks. • If you request information on a single exchange, then the monitor will display a more detailed description. The description includes the: − exchange name − queuing mechanism (FIFO or priority) − access rights (group only or unlimited), and − queue length (unlimited or decimal notation limit), followed by a list of: all queued processes, and all queued messages. Syntax Below is usage and syntax information for this command Command Format CPM / D20 / D25: qx [(xid | name)] CCU / CCUME: qx [(xid | gxid | name)] Variables None Parameters (none) = displays general information for all exchanges . xid = pSOS exchange ID (in hexadecimal); displays detailed information for a specific exchange. gxid = global pSOS exchange ID (in hexadecimal); displays detailed information for a specific exchange. name = case-sensitive exchange name. It now supports the new exchange naming convention. If you enter an entire name, the monitor displays detailed information for that exchange. If you enter the first few characters, the command attempts pattern matching. The monitor displays general or detailed information, depending on the number of matches. Continued on next page 68K System Monitor User's Guide GE Energy Services General SWM0023-1.00 -2 Full Release 3-55 QX - Query Exchange, Continued Syntax (continued) Example Type qx and press ENTER. Results: The system displays the name, exchange ID, and number of queued processes and messages for every exchange in the system. Special Considerations None GE Energy Services 68K System Monitor User's Guide SWM0023 1.00 2 General 3-56 Full Release RB - Resume Breakpoint Platform þ CPM þ D20 D20 Base o D20 ME D20 Base o D20/200 CCU Base þ D20/200 ME CCU Base þ D25 Description Use this command to restart a process that stopped at a breakpoint, without removing the breakpoint. It verifies the specified breakpoint, restarts the associated process, and then reinserts the breakpoint trap. Syntax Below is usage and syntax information for this command Command Format rb break_pt# [#reps] Variables None Parameters break_pt# = breakpoint number as returned with the define breakpoint command. #reps = number of times (in decimal) to repeat execution of the breakpoint address before stopping; default is zero. Example Type rb 1 and press ENTER. This resumes breakpoint number one (1) that stops again before the second execution of the instruction at the breakpoint address. Results: The system responds with the prompt. Whenever it encounters a breakpoint, the system displays the breakpoint number, loop count, and register values. If the loop count is greater than zero, it is decremented. Otherwise, the process is suspended. Special Considerations None 68K System Monitor User's Guide GE Energy Services General SWM0023-1.00 -2 Full Release 3-57 RP - Resume Process Platform þ CPM þ D20 D20 Base þ D20 ME D20 Base þ D20/200 CCU Base þ D20/200 ME CCU Base þ D25 Description Use this command to restart all processes, some processes, or a specific suspended process. Use this command to restart processes that have been suspended using the suspend process (SP) command. Syntax Below is usage and syntax information for this command Command Format CPM / D20 / D25: rp [(pid | name)] CCU / CCUME: rp [(pid | gpid | name)] Variables None Parameters (none) = resume all processes. pid = pSOS process ID (in hexadecimal); resume a specific process. gpid = global pSOS process ID (in hexadecimal); resume a specific process name = case-sensitive process name. The monitor supports the new process naming convention. If you enter an entire name, the monitor resumes the specified process. If you enter the first few characters, the command attempts pattern matching. The monitor will then resume all matching processes. Example Type rp and press ENTER. This enables all suspended processes to resume execution. Results: Unless it encounters an error, the system displays the prompt. If it encounters an error, the system displays an error message before it returns to the prompt. Special Considerations Do not use this command to start a D25 after an NVRAM download or after an error caused it to halt. In these cases, you must reboot the D25 to ensure that all parameters and variables are re-initialized properly. GE Energy Services 68K System Monitor User's Guide SWM0023 1.00 2 General 3-58 Full Release RR - Report RAM Partitions Platform o CPM o D20 D20 Base o D20 ME D20 Base þ D20/200 CCU Base þ D20/200 ME CCU Base þ D25 Description Use this command to display information on the RAM divisions currently configured in the system. • On a D25 platform, this command reports the base addresses of the RAM and NVRAM regions, and the size of the NVRAM region. • On a D200 platform, this command reports the base addresses of the global RAM and global NVRAM regions, and the size of the global NVRAM region. In either case, the monitor reports total amount of free RAM. Syntax Below is usage and syntax information for this command Command Format rr Variables None Parameters None Example Type rr and press ENTER. Results: The monitor displays the information about existing RAM configuration. Special Considerations None 68K System Monitor User's Guide GE Energy Services General SWM0023-1.00 -2 Full Release 3-59 RT - RAM Test Platform þ CPM þ D20 D20 Base þ D20 ME D20 Base þ D20/200 CCU Base þ D20/200 ME CCU Base þ D25 Description Use this command to perform a non-destructive read-write test of specified RAM memory. The test may be for the entire RAM or NVRAM regions, or for a specified range of values. You may also select to run the test for a set number of loops, or to loop infinitely. Note: If the input range is not on long word boundary, set the range ending address to the first lesser word boundary. Syntax Below is usage and syntax information for this command Command Format CPM / D20: rt / (v | n) CCU / CCUME: rt / (v | n | gv | gn) [beg_addr end_addr [(#loops | i)]] D25: rt / (v | n | s) [beg_addr end_addr [(#loops | i)]] Variables /v = volatile (static) RAM /n = non-volatile RAM (NVRAM) /s = destructive sequential test /gv = global volatile (static) RAM /gn = global non-volatile RAM (NVRAM) Parameters beg_addr = first address of memory range (in hexadecimal) end_addr = end address of memory range (in hexadecimal) #loops = number of times to execute the finite loop for the specified memory (in decimal) before stopping i = use infinite loop Example Type rt /gn 510000 5100b0 25000 and press ENTER. Results: This tests the integrity of the global non-volatile (static) RAM between the memory range of 510000 and 5100b0 repeatedly for 25,000 times. The system simply returns the prompt when it successfully completes this instruction. If the test fails, the system displays an error message before returning to the prompt. Continued on next page GE Energy Services 68K System Monitor User's Guide SWM0023 1.00 2 General 3-60 Full Release RT - RAM Test, Continued Syntax (continued) Special Considerations If you enable the Debug Mode, the function can be CPU intensive, and could cause a system reset under these circumstances. You cannot use this function when the NVRAM is corrupt. Do not use the /s switch on a D25. 68K System Monitor User's Guide GE Energy Services General SWM0023-1.00 -2 Full Release 3-61 RTB - Return To BootROM Platform o CPM o D20 D20 Base o D20 ME D20 Base o D20/200 CCU Base o D20/200 ME CCU Base þ D25 Description Use this command to place the device in System Service Mode. When you issue the command, the system stops executing out of the FLASH region, and it activates the BootROM operating system. The primary use of this mode is for the downloading of FLASH application software to the RTU. Syntax Below is usage and syntax information for this command Command Format rtb Variables None Parameters None Example At the monitor prompt, type rtb and press ENTER. Results: The system returns to BootROM operation mode. Special Considerations The system halts and deletes all applications currently executing on the RTU when it activates the BootROM operating system. GE Energy Services 68K System Monitor User's Guide SWM0023 1.00 2 General 3-62 Full Release RTC - Test CCU RTC Platform o CPM o D20 D20 Base o D20 ME D20 Base o D20/200 CCU Base o D20/200 ME CCU Base o D25 Description Use this command to test the RTC synchronization between nodes in a D200. Syntax Below is usage and syntax information for this command Command Format rtc [/r] Variables /r = reset back to initial settings Parameters None Example At the monitor prompt, type rtc /r and press ENTER. Special Considerations None 68K System Monitor User's Guide GE Energy Services General SWM0023-1.00 -2 Full Release 3-63 RX - Request Exchange Platform þ CPM þ D20 D20 Base þ D20 ME D20 Base þ D20/200 CCU Base þ D20/200 ME CCU Base þ D25 Description Use this command to retrieve a message from one or more exchanges. It returns the first message in each target message queue. Syntax Below is usage and syntax information for this command Command Format rx (xid | name) Variables None Parameters xid = pSOS exchange ID (in hexadecimal); make an attempt to retrieve a message from a single exchange. name = case-sensitive exchange name. The monitor supports the new exchange naming convention. If you enter an entire name, the monitor retrieves the message from that exchange. If you enter the first few characters, the command attempts pattern matching. The monitor retrieves messages from one or more exchanges, depending on the number of matches. Example Type rx 304540 and press ENTER. This requests a message from the exchange with an ID of 304540. Results: The message is displayed as six long, hexadecimal words as: A999 : 00000001 00000002 00000003 00000004 The system displays the specified message, then returns to the prompt unless it encounters an error. If this is the case, it displays an error message before it returns to the prompt. Special Considerations You must only use this command in a testing or debugging context. If you take a message from an exchange indiscriminately, you cannot predict the results. GE Energy Services 68K System Monitor User's Guide SWM0023 1.00 2 General 3-64 Full Release RZ - ZMODEM Download Platform o CPM o D20 D20 Base o D20 ME D20 Base o D20/200 CCU Base o D20/200 ME CCU Base o D25 Description Use this command to download configuration and application data over the serial port into RAM or FLASH. The 68K Monitor accepts a transfer of ZMODEM binary data to the D25 initiated either by the D25 user or by the sending terminal. When the transfer is complete, the DOWNLOAD command returns control to 68K Monitor’s command line. Application code download only works when: • executing from the BootROM, and • the monitor has erased the FLASH region. While the command downloads the file, it recognizes the ZLIB format of the compressed data and uncompresses it. Syntax Below is usage and syntax information for this command Command Format rz [/(Vlevel | Mtimeout | Ctimeout | Wwindow)] Variables /Vlevel verbose level, which determines the level of debug messages displayed (default is zero, any non-zero value will activate debug messages). /Mtimeout set receive message timeout to the user specified value (the default is 2000 ms). /Ctimeout set inter-character timeout to user specified value (default is 500 ms). /Wwindow set receiver window size to user specified value (default is 1400 bytes). Special Considerations Before the start of the download, the system must suspend all non-protected process running in the system. • If there are parameters on the command line, the monitor assumes that the D25 initiated the download, and allows 20 seconds for the user to activate the software that will send data to the D25. • If there are no parameters, the monitor assumes that the sending software initiated the download and it will not provide a wait period. The command “rz” is the standard prefix used by the ZMODEM binary protocol to start a file transfer. A terminal using this command can connect to the D25 Monitor and simply start sending ZMODEM data without any further user input to the D25. Continued on next page 68K System Monitor User's Guide GE Energy Services General SWM0023-1.00 -2 Full Release 3-65 RZ - ZMODEM Download, Continued ! WARNING Executing this command modifies the memory of the D25, and can cause operational disruption. Use caution before proceeding. Be sure that you really want to use this command and that you use it correctly. Note K K K K When using ZMODEM, all files sent to the 68K Monitor must have file names. The file name for a FLASH image must start with “PROM”. The file name for a ZLIB compressed image must end with the extension “.ZLB”. The name in these cases is case insensitive (i.e. “prom” and “.zlb” are acceptable as well). The monitor assumes that any other names are non-compressed NVRAM configuration data. Since there is no addressing inherent in ZMODEM data, you must change the location of NVRAM in any existing configuration before downloading if you want to change the NVRAM header address. GE Energy Services 68K System Monitor User's Guide SWM0023 1.00 2 General 3-66 Full Release SA - Serial Analyzer Platform þ CPM þ D20 D20 Base þ D20 ME D20 Base o D20/200 CCU Base þ D20/200 ME CCU Base þ D25 Description Use this command to monitor communications on one of the defined serial ports (other than the assigned 68K Monitor port). It uses serial I/O system transmit and receive call-outs to intercept all communications on the channel. Syntax Below is usage and syntax information for this command Command Format sa port Variables None Parameters port = serial port to monitor (COM#) Example Type sa com7 and press ENTER. Results: This activates the serial analyzer monitor on communications port seven (SIO7). The monitor displays all communications on the specified channel until it receives CNTRL-C on the monitor channel. The display then returns to the prompt. Special Considerations This function cannot be used on the port assigned to 68K Monitor (COM0), the SPI port (_SPI), or the SCC1 port (SCC1). This function is completely non-intrusive. It cannot affect the operation of the application that owns the monitored port. Error Codes If any of the following receiver errors are detected, these codes are displayed: − over-run errors OV − parity errors PA − framing errors FR − detected breaks BR. Display Format The monitor displays all data transmitted and received in hexadecimal format. Transmit data is displayed in inverse video; receive data is normal video mode. Continued on next page 68K System Monitor User's Guide GE Energy Services General SWM0023-1.00 -2 Full Release 3-67 SA - Serial Analyzer, Continued Buffered Data The serial analyzer does not display data immediately. It buffers the data so that the serial analyzer remains non-intrusive. The buffer is large enough (1000 bytes) that overflow is unlikely. If the buffer does overflow, however, the indication provided is: buffer overflow The monitor discards incoming data as long as the buffer is in the overflow state. It does not destroy the current buffer contents. GE Energy Services 68K System Monitor User's Guide SWM0023 1.00 2 General 3-68 Full Release SB - Step Breakpoint Platform þ CPM þ D20 D20 Base o D20 ME D20 Base o D20/200 CCU Base þ D20/200 ME CCU Base þ D25 Description Use this command to single step a process that was suspended at a breakpoint. It also allows executing multiple program steps in a single command. Syntax Below is usage and syntax information for this command Command Format sb break_pt# [#instructions] Variables None Parameters break_pt# = breakpoint number as returned with the define breakpoint command. #instructions = number of additional instructions to execute prior to stopping; default is zero. Example Type sb 2 1 and press ENTER. This allows the process defined by the breakpoint number of 2 to perform two program instructions. Results: The system responds with the prompt. Additionally, each time it completes a program step, the system displays the breakpoint number, instruction count, and register values. If the instruction count is greater than zero, it is decremented. Otherwise, the process is suspended. Special Considerations None 68K System Monitor User's Guide GE Energy Services General SWM0023-1.00 -2 Full Release 3-69 SC - Select Active Configuration Platform o CPM o D20 D20 Base o D20 ME D20 Base þ D20/200 CCU Base þ D20/200 ME CCU Base þ D25 Description Use this command to select one of the stored configurations as the active configuration. The system is halted and the stored configuration is uncompressed (if necessary) and written into NVRAM (local on the D25, global on a D200) as the new configuration. The selected configuration file is marked as the active configuration. Note: Upon completion, the Monitor leaves the system halted so that you can restart the system with the new configuration. Syntax Below is usage and syntax information for this command Command Format sc (file_num | file_name) [BaseAddress] Variables None Parameters file_num = The query configuration storage parameters command displays all existing files, giving each a numerical index. The monitor uses this index with the command to specify the file that it will copy into memory and make active. file_name = The name of the configuration file to select. The command will select the first matching configuration it finds. BaseAddress = base address at which to write the new configuration Example Type sc config.bin and press ENTER. Results: The monitor selects the stored configuration "config.bin" as the active configuration and copies it into NVRAM, overwriting the existing configuration. Special Considerations Once this function is invoked, it may take some time for the configuration to be decompressed (if necessary), and written into memory. GE Energy Services 68K System Monitor User's Guide SWM0023 1.00 2 General 3-70 Full Release SET - Set System Parameters Platform o CPM o D20 D20 Base o D20 ME D20 Base o D20/200 CCU Base þ D20/200 ME CCU Base þ D25 Description Note: This command is for developers only. Use this command to quickly modify options in code during run time. Syntax Below is usage and syntax information for this command Command Format set [/h] <option> [(/d | <parameters>)] Variables /h = help /d = ? Parameters option = depends on application parameters = depends on application Example Not required Special Considerations Very dangerous to use, only for programmers. 68K System Monitor User's Guide GE Energy Services General SWM0023-1.00 -2 Full Release 3-71 SI - Display System Information Platform o CPM o D20 D20 Base o D20 ME D20 Base þ D20/200 CCU Base þ D20/200 ME CCU Base þ D25 Description Use this command to display information on the hardware, software and current configuration of the device. Syntax Below is usage and syntax information for this command Command Format si Variables None Parameters None Example Type si and press ENTER. Results: The monitor displays information on the configuration of the system. Special Considerations In earlier versions of the Monitor, this command was dhw . GE Energy Services 68K System Monitor User's Guide SWM0023 1.00 2 General 3-72 Full Release SP - Suspend Process Platform þ CPM þ D20 D20 Base þ D20 ME D20 Base þ D20/200 CCU Base þ D20/200 ME CCU Base þ D25 Description Use this command to stop all unprotected processes, some unprotected processes, or a specific unprotected process. Use this command to stop all processes before CPU-intensive operations, for example, an NVRAM download. Protected processes must remain running at all times. Protected processes include: • MON monitor input process • MOUT monitor output process • WDOG watchdog process • ROOT root process • IDLE pSOS idle process • LGIN boot login process (in some cases) • iSCS processes, including B100 and file managers. Syntax Below is usage and syntax information for this command Command Format CPM / D20 / D25: sp [(pid | name)] CCU / CCUME: sp [(pid | gpid | name)] Variables None Parameters (none) = suspend all unprotected processes. pid = pSOS process ID (in hexadecimal); suspend a specific process. gpid = global pSOS process ID (in hexadecimal); suspend a specific process. name = case-sensitive process name. The monitor supports the new process naming convention. If you enter an entire name, a specific process is suspended. If you enter the first few characters, the command attempts pattern matching. All matching processes are suspended. Continued on next page 68K System Monitor User's Guide GE Energy Services General SWM0023-1.00 -2 Full Release 3-73 SP - Suspend Process, Continued Syntax (continued) Example Type sp and press ENTER. Results: This suspends all unprotected processes. Unless it encounters an error, the system displays the prompt. If it encounters an error, it displays an error message before it returns to the prompt. Special Considerations This function stops the execution of tasks within the remote; you must not use it when the remote is active. Note: The safe way to restore normal operation after using this command is to reboot. GE Energy Services 68K System Monitor User's Guide SWM0023 1.00 2 General 3-74 Full Release ST - Serial Test Platform þ CPM þ D20 D20 Base þ D20 ME D20 Base þ D20/200 CCU Base þ D20/200 ME CCU Base þ D25 Description Use this command to start one of these two serial port test procedures: • an automatic loop-back test of the defined serial port − transmits and receives a series of characters of different formats. • manually forcing the mark or space line states from the RS-232 drivers − allows you to monitor and adjust modem levels or frequencies. Syntax Below is usage and syntax information for this command Command Format CPM / D20: st /(f | l) port CCU / CCUME / D25: st /(f | l) port [baud] Variables /f = force mark or space states /l = automatic loop-back test Parameters port = serial port to test (COM#) baud = data rate in bps (decimal) Example Type st /l com7 9600 and press ENTER. Results: This forces the RS-232 transmitter driver for communications port seven (7) to perform the loop- back test at 9600 bps. The system displays the current state of the test. Cancel the force test manually with CTRL-C. The loop-back test terminates either on an error or on completion of the test. The monitor displays the prompt after stopping either test. Special Considerations • These tests temporarily assume control of the specified communications port, and disrupt any current activity. • They may also, depending on the application, affect subsequent operation. To ensure that you avoid this, you must reboot the system when you complete all testing. Continued on next page 68K System Monitor User's Guide GE Energy Services General SWM0023-1.00 -2 Full Release 3-75 ST - Serial Test, Continued Loop Test Adapter The automatic loop-back test requires this DB-9 pin loop-back connector: DCD 1 ────┐ RXD 2 ──┐ │ TXD 3 ──┘ │ RTS 7 ────┤ CTS 8 ────┘ Selectable Data Rates The command used in CCU-based and D25 products allows you to select the data rate for the loopback test. Supported data rates in bps are: 50 110 134 200 300 600 1050 1200 2400 4800 7200 9600 38400 ! WARNING The command has failed when used for stress testing. Do not use the serial test for that purpose! You must only use it to verify the device driver for the communication port. GE Energy Services 68K System Monitor User's Guide SWM0023 1.00 2 General 3-76 Full Release SX - Send Exchange Platform þ CPM þ D20 D20 Base þ D20 ME D20 Base þ D20/200 CCU Base þ D20/200 ME CCU Base þ D25 Description Use this command to queue a message at one or more exchanges. Syntax Below is usage and syntax information for this command Command Format CPM / D20 / D25: sx (xid | name) m2 m3 m4 m5 CCU / CCUME: sx (xid | gxid | name) m2 m3 m4 m5 [/g] Variables /g = Allows the message to be sent to a queue in a different node Parameters xid = pSOS exchange ID (in hexadecimal); send message to a specific exchange. gxid = global pSOS exchange ID (in hexadecimal); send message to a specific exchange. name = case-sensitive exchange name. The command supports the new exchange naming convention. If you enter an entire name, the system sends the message to that exchange. If you enter the first few characters, the command attempts pattern matching. The system sends the message to one or more exchanges, depending on the number of matches. m2 - m5 = first through fourth long words in the body of the message, in hexadecimal. Example Type sx 304540 1 2 3 4 and press ENTER. This sends a message identified as 304540. The command sets the first two reserved messages to 0. Results: The system displays the prompt unless it encounters an error. In this case, it displays an error message before displaying the prompt. Special Considerations You must only use this command in a testing or debugging context. If you send a message to an exchange indiscriminately, you cannot predict the results. 68K System Monitor User's Guide GE Energy Services General SWM0023-1.00 -2 Full Release 3-77 SYSC - System Platform o CPM o D20 D20 Base o D20 ME D20 Base o D20/200 CCU Base o D20/200 ME CCU Base þ D25 Description Use this command to reset the reboot counter to zero. Syntax Below is usage and syntax information for this command Command Format sysc [(/?) | command] Variables /? = help Parameters command = rcount Example Type sysc rcount and press ENTER. Results: The reboot counter will be reset to 0. Special Considerations None. GE Energy Services 68K System Monitor User's Guide SWM0023 1.00 2 General 3-78 Full Release TEST - Invoke Test Tool Platform o CPM o D20 D20 Base o D20 ME D20 Base o D20/200 CCU Base þ D20/200 ME CCU Base þ D25 Description Use this command to activate a test tool external to the monitor. To use a test tool, the test tool application must: • be included in the software for the system, and • be created specifically to make use of this monitor function. The 68K Monitor relinquishes communications control to the test tool and waits for the tool to complete its processing before continuing. Syntax Below is usage and syntax information for this command Command Format test proc_name Variables None Parameters proc_name = The name of the test tool process, normally Txxx . Example None Required Special Considerations If the test tool application is suspended, the command will not function. The monitor must detect that the test tool is waiting for a signal before it will proceed. 68K System Monitor User's Guide GE Energy Services General SWM0023-1.00 -2 Full Release 3-79 TR - Trace Platform o CPM o D20 D20 Base o D20 ME D20 Base o D20/200 CCU Base o D20/200 ME CCU Base o D25 Description Use this command to track the execution sequence of the processes in the system. Syntax Below is usage and syntax information for this command Command Format tr [/h | /c | /s] tr /d [/c] [/e] [<start_time> [<end time>] ] tr /r [/g] [<samples>] /t0 <pre_trigger> <address> <condition> <value> tr /r [/g] [<samples>] /t1 <pre_trigger> <trigger time> tr /r [/g] [<samples>] /t2 <pre_trigger> <process name> Variables /h = display help /c = clear all /s = stop collection /d = display gathered data /c – continuous display, /e – format for spread sheets /r = gather data /g = allocate buffers from global memory Parameters start_time = start time for trace to display. end time = end time for trace to display. pre_trigger = number of samples to store before the trigger address = the watch address to trigger on condition = Condition to watch for = != < > <= >= change value = value to watch for trigger time = RTC time to trigger process name = name of process to trigger on Continued on next page GE Energy Services 68K System Monitor User's Guide SWM0023 1.00 2 General 3-80 Full Release TR - Trace, Continued Syntax (continued) Example 1 Type tr /r 20 /t0 10 208000 = 12345678 and press ENTER. Results: This will allocate a buffer for 20 samples and triggers when the long memory location becomes 12345678. It saves 10 samples before the trigger, the trigger sample and 9 samples more to fill the buffer. Example 2 Type tr /r 20 /t0 10 208000 change and press ENTER. Results: This triggers if the long memory location changes value. Example 3 Type tr /r 20 /t0 10 208000 != 12345678 and press ENTER. Results: This triggers if long memory value changes from the value 12345678. Example 4 Type tr /r 20 /t1 10 00123456 and press ENTER. Results: This triggers when the RTC value if greater than or equal to 00123456. Example 5 Type tr /r 20 /t2 10 30123456 and press ENTER. Results: This triggers after the process with the ID of 30123456 runs. Special Considerations This function is only available as a special debug BootROM as there is not enough room for it to be permanently included. Currently, the BootROM code must have the TRACE command compiled into S043-0 before you can use this command. You will have to remove some other commands in order to make room for it. 68K System Monitor User's Guide GE Energy Services General SWM0023-1.00 -2 Full Release 3-81 UL - Upload Platform þ CPM þ D20 D20 Base þ D20 ME D20 Base o D20/200 CCU Base þ D20/200 ME CCU Base þ D25 Description Use this command to retrieve an S-record from the device’s memory. Syntax Below is usage and syntax information for this command Command Format CPM / D20: ul CCU / CCU ME / D25: ul beg_addr end_addr [width] Variables None Parameters beg_addr = start of address range end_addr = end of address range Example Type ul and press ENTER. Results: uploads the contents of NVRAM to the terminal, and returns to the prompt when completed. Special Considerations None GE Energy Services 68K System Monitor User's Guide SWM0023 1.00 2 General 3-82 Full Release VER - Version Platform þ CPM þ D20 D20 Base þ D20 ME D20 Base þ D20/200 CCU Base þ D20/200 ME CCU Base þ D25 Description Use this command to display the Base System and pSOS versions, plus any application version and embedded image information. On the D25, the monitor will also display the BootROM version. The provided information consists of: name - application or embedded image name version - image version number level - image compilation level target - hardware target (i.e., D20M++, D25, D25_FF) date - image compilation date and time Syntax Below is usage and syntax information for this command Command Format D20 / CCU / CCU ME: ver D25: ver [/d] Variables /d Display DSP flash versions Parameters None Example Type ver and press ENTER. Results: The monitor displays at least the boot code and pSOS version information and returns to the prompt. Special Considerations None 68K System Monitor User's Guide GE Energy Services General SWM0023-1.00 -2 Full Release 3-83 VP - Signal Process Platform þ CPM þ D20 D20 Base þ D20 ME D20 Base þ D20/200 CCU Base þ D20/200 ME CCU Base þ D25 Description Use this command to send a pSOS signal to one or several processes. Use it during development of application software. Syntax Below is usage and syntax information for this command Command Format CPM / D20 / D25: vp (pid | name) event CCU / CCUME: vp (pid | gpid | name) event Variables None Parameters pid = pSOS process ID (in hexadecimal); send the signal to a specific process. gpid = global pSOS process ID (in hexadecimal); send the signal to a specific process. name = case-sensitive process name. The command supports the new naming convention. If you enter an entire name, the command sends the signal to a specific process. If you enter the first few characters, the command attempts pattern matching. It then sends the signal to all matching processes. event = hexadecimal format word of the bits with which to signal the process(es). Example Type vp 308048 1000 and press ENTER. This signals the process with pSOS ID 308048 with the 13th bit (i.e., bit 12) zero-based. Results: Unless it encounters an error, the system displays the prompt. If it encounters an error, it displays an error message before it returns to the prompt. Special Considerations You must only use this command as a testing or debugging mechanism. If you send an indiscriminate signal to a process, you cannot predict the results. Note: The safe way to restore a system to normal operation after using this command is to reboot. GE Energy Services 68K System Monitor User's Guide SWM0023 1.00 2 General 3-84 Full Release WINM - WIN Metrics Platform o CPM o D20 D20 Base o D20 ME D20 Base o D20/200 CCU Base o D20/200 ME CCU Base o D25 Description Use this command to report statistics on processing in the Base System software. Syntax Below is usage and syntax information for this command Command Format winm ((/r [data_type]) | data_type) Variables /r = reset Parameters data_type = <refer to code> Example Not required. Special Considerations Requires special code to use this command. General SWM0023-1.00 -2 Full Release I-1 Index B Boot Command BOOT ...........................................................................3-7 C Calibrate KI Command CAL ..............................................................................3-9 Change Auto-logout Timer Command AL.................................................................................3-4 Change Configuration File Attributes Command CCA ............................................................................ 3-11 Change Priority Command CP ............................................................................... 3-17 Check Sum Command CS ............................................................................... 3-18 Clear Breakpoint Command CB............................................................................... 3-10 Clear Configuration File Command CCF............................................................................. 3-14 Clear Screen Command CLS ............................................................................. 3-16 Control Cache Command CACHE.........................................................................3-8 Copy File Command CF ............................................................................... 3-15 Create Configuration Storage Block Command CCB ............................................................................ 3-12 D Debug Mode Command DEBUG....................................................................... 3-22 DM.............................................................................. 3-28 Decompression Status Command DSTAT ....................................................................... 3-29 Define Breakpoint Command DB............................................................................... 3-21 Directory Command DIR ............................................................................. 3-25 Display File Data Command DF ............................................................................... 3-23 Display Hardware Command DHW........................................................................... 3-24 Display Image Information Command IMG............................................................................. 3-41 Display System Information Command SI................................................................................. 3-71 Download Command DL .............................................................................. 3-27 Dump Memory Command D................................................................................. 3-19 E Echo Toggle Command ECHO......................................................................... 3-32 Edit Memory Command E ................................................................................. 3-30 Error Log Command EL............................................................................... 3-33 Ethernet Address Command ETH ............................................................................ 3-35 Exit Command EXIT........................................................................... 3-36 F Fill Memory Command F ................................................................................. 3-37 Find Table Command FT ............................................................................... 3-38 Flash Erase Command ERASE ....................................................................... 3-34 H HDLC Test HT .............................................................................. 3-40 Help Command HELP.......................................................................... 3-39 I Invoke Test Tool Command TEST .......................................................................... 3-78 J Jam Exchange Command JX ............................................................................... 3-43 Jump To Flash Command JTF.............................................................................. 3-42 GE Energy Services 68K System Monitor User's Guide SWM0023 1.00 2 General I-2 Full Release K KI Metrics Command KIM ............................................................................ 3-44 M Move Memory Command M................................................................................. 3-45 P Print Breakpoint Command PB ............................................................................... 3-46 Profile Command PR ............................................................................... 3-47 Program Flash Command PRG ............................................................................ 3-49 Q Query Configuration Storage Parameters Command QC............................................................................... 3-50 Query Exchange Command QX .............................................................................. 3-54 Query Process Command QP ............................................................................... 3-51 Query RAM Command QR............................................................................... 3-53 R RAM Test Command RT ............................................................................... 3-59 Report RAM Partitions Command RR............................................................................... 3-58 Request Exchange Command RX............................................................................... 3-63 Resume Breakpoint Command RB............................................................................... 3-56 Resume Process Command RP ............................................................................... 3-57 Return To BootROM Command RTB............................................................................. 3-61 S Select Active Configuration Command SC............................................................................... 3-69 Send Exchange Command SX............................................................................... 3-76 Serial Analyzer Command SA............................................................................... 3-66 Serial Test Command ST ............................................................................... 3-74 Set System Parameters Command SET............................................................................. 3-70 Signal Process Command VP............................................................................... 3-83 Step Breakpoint Command SB............................................................................... 3-68 Suspend Process Command SP ............................................................................... 3-72 System Command SYSC.......................................................................... 3-77 T Test CCU RTC Command RTC ............................................................................ 3-62 Trace Command TR............................................................................... 3-79 U Upload Command UL .............................................................................. 3-81 V Version Command VER............................................................................ 3-82 W WIN Metrics Command WINM ........................................................................ 3-84 Z ZMODEM Download Command RZ............................................................................... 3-64