McIntosh MC275

Manual text content

MC275 STEREO POWER AMPLIFIER GENERAL DESCRIPTION Over one million watts of amplifier output power capacity have been manufactured by Mclntosh since 1947. In this 1,000,000 watts of audio power there are less than 10 watts of distortion capacity and less than 1/100 watt of noise capacity! The dramatic difference in the quality of music reproduction when you listen through Mclntosh instruments is directly due to low distortion performance. Careful, devoted research is a way of life at Mclntosh. The world's finest amplifier is the creation of per- severing, resourceful Mclntosh engineers. Mclntosh Laboratory is the only manufac- turer in the entire industry to guarantee the lowest distortion at all audio frequencies, at full power. The U.S. Patent Office has rec- ognized the advanced technology of the Mclntosh circuit by granting 6 patents. 1 Long life, flexibility, highest quality con- struction are characteristic designs in every Mclntosh instrument. Wide electrical and thermal margins of safety for all components and tubes, advanced engineering, and cool operating design add to the long life built into every Mclntosh product. Reliability pro- longs your investment without expensive maintenance costs. The MC275 has on one chassis two 75 watt power amplifiers. In addition to use as a stereo amplifier, the flexibility of the MC275 permits it to be used as a monophonic amplifier that delivers 150 watts, or as two separate 75 watt amplifiers with each chan- nel amplifying completely separate pro- grams, or as two amplifiers for use with an electronic crossover network. Such flexi- bility permits maximum use for greatest return from your investment. TECHNICAL DESCRIPTION The patented Mclntosh Unity Coupled circuit and output transformer have estab- lished Mclntosh amplifiers as the unchal- lenged leaders in the audio field. Before 1947, low distortion at high power and high efficiency was impossible. A com- pletely new engineering approach resulted in an amplifier that for the first time permitted high power with distortion below 1%. That new engineering produced the Mclntosh Unity coupled circuit and the Mclntosh bifilar wound output transformer. With the intro- duction of the Mclntosh amplifier new stand- ards for distortion-free performance were established. PRIMARY NO. I turn of primary number one is next to the same turn of primary number two. There is almost complete magnetic coupling between the two wires. The magnetic coupling is rein- forced by the capacitance between the two wires. INPUT OUTPUT PRIMARY NO. 2 Fig. 1—Representation of bifilar winding. The Mclntosh output transformer is unique. It has two primary windings which are wound bifilarly. In the bifilar technique both primary wires are wound side by side. Each Fig. 2—Representation of Mclntosh output circuit. 1 U.S. Patent No's: 2,477,074; 2,545,788; 2,646,467; 2,654,058; 2,860,192; 2,929,028. 1 ELECTRICAL SPECIFICATIONS Power Output: Stereo or twin amplifier—75 watts con- tinuous per channel Monophonic—150 watts continuous Harmonic Distortion: Less than 0.5% at rated output or less, 20 cycles through 20,000 cycles. Typical performance is 0.3% or less at 20 cycles and 20,000 cycles at full power. Typical performance in the mid frequencies is 0.1% or less at full power. Intermodulation Distortion: Less than 0.5% for any combination of frequencies from 20 cycles through 20,000 cycles if instantaneous peak power is below twice the rated power. Phase Shift: Less than ±8° 20 cycles through 20,000 cycles Frequency Range: At rated output: +0, -0.1 db 16 cycles through 40,000 cycles +0, -0.5 db 16 cycles through 60,000 cycles At one-half rated output: +0, -1 db 10 cycles through 100,000 cycles Noise and Hum: 90 db or more below rated output Output Impedance: Stereo or Twin Amp: (Isolated from ground) 4 ohms, 8 ohms, 16 ohms (Center tap internally grounded) 600 ohms (One side internally grounded) 67 ohms, 150 ohms Mono: (Isolated from ground) 2 ohms, 4 ohms, 8 ohms, 16 ohms, 32 ohms (Center tap internally grounded) 300 ohms (One side internally grounded) 34 ohms, 75 ohms Output Voltage: Stereo or Twin Amp: (Isolated from ground) 25 volts (Center tap internally grounded) 230 volts (One side internally grounded) 70.7 volts, 115 volts Mono: (Isolated from ground) 25 volts, 70.7 volts (Center tap internally grounded) 230 volts (One side internally grounded) 70.7 volts, 115 volts Internal Impedance: Less than 10% of rated load impedance Input: Input impedance—250,000 ohms Input sensitivity—0.5 volts to 30 volts through gain control with input switch in MONO or TWIN AMP position. With the switch in the STEREO position, sensi- tivity is 2.0 volts through a balance control. Power Requirements: 105 volts to 130 volts at 50/60 cycles: 240 watts at zero signal output: 400 watts at rated output. The power trans- former is tapped for 117 volts and 125 volts. Tube Complement: Voltage Amplifier—One 12AX7 (drives both amps) Phase Inverter—Two 12AU7 Drive Amplifier—Two 12BH7 Cathode Follower Drive—Two 12AT7 or 12AZ7 Output—Four KT88 or 6550 MECHANICAL SPECIFICATIONS Dimensions: Chassis dimensions: 17 ¼ " long x 12 ¼ ' wide x 8" high. (See INSTALLATION on Page 5 for minimum mounting space.) Weight: Chassis only—67 ½ pounds. In shipping carton—76 pounds. Finish: Chromium and Black Accessories Supplied: Owners Manual Mounting Template Mounting Flanges Octal output plug with cap 3 PANEL FACILITIES Fig. 3—The end panel of the MC275 showing all input and output facilities. INPUT The input of the MC275 has a three posi- tion lever switch to permit the amplifier to be used in any one of three ways: (1) As a monophonic 150 watt amplifier (2) As twin 75 watt amplifiers used with an electronic crossover network, or two completely separate amplifiers, or in stereo applications requiring 0.5 volt sensitivity in the power amplifiers (3) As a stereo amplifier used with a Mclntosh preamplifier or other high output stereo program sources. The input marked STEREO has a sensi- tivity of 2.0 volts controlled by a BALANCE control. The input impedance is 250,000 ohms. The input marked TWIN AMP has a sensi- tivity of 0.5 volt. Each TWIN AMP input is controlled by a GAIN control. The GAIN con- trol allows signal sources with output from 0.5 volt up to 30 volts to be connected with- out overloading the input to the amplifier. The input impedance is 250,000 ohms. The input marked MONO has a sensitivity of 0.5 volt. The MONO position of the input switch parallels the inputs to both ampli- fiers. When the outputs are properly con- nected the MC275 becomes a 150 watt monophonic amplifier. The MONO input has a GAIN control that permits connecting signal sources up to 30 volts without overloading the amplifier's input. The input impedance is 250,000 ohms. OUTPUT The two barrier terminal strips marked OUTPUT provide stereo connections for the normal speaker impedances of 4 ohms, 8 ohms, and 16 ohms. For monophonic oper- ation connections for 2 ohms, 4 ohms, 8 ohms, 16 ohms, and 32 ohms are provided. The terminal strips may also be connected for a constant voltage output of 25 volts in either stereo or mono, or for 70.7 volts in mono. The secondary of the Mclntosh output transformer may be operated either grounded or not grounded. As supplied, the secondary of the MC275 is not grounded. If grounding is desirable a wire may be connected be- tween chassis and common of either or both output terminal strips. The barrier strip output connections are fed from the secondary of the output trans- former, LINE OUTPUT (See also pages 5, 6 and 7) The octal socket marked LINE OUTPUT has connections for 70.7 volts, 115 volts, 230 volts, or 600 ohms for stereo operation. For monophonic operation the octal socket provides connections for 70.7 volts, 115 volts, 230 volts, or 300 ohms. The 600 ohm winding and the 300 ohm winding are balanced to ground. Pin 1 of the octal socket is the center tap for these wind- ings and is grounded. The connections at the octal socket are fed from taps on the cathode winding in the primary of the output transformer. FUSE The MC275 uses a 5.0 ampere slo-blo type fuse. The auxiliary AC socket is not fused. AC OUTLET The auxiliary AC outlet can be used to supply power to other equipment in the 4 system. The outlet will provide a maximum of 300 watts of power. The AC outlet is not fused. LINE VOLTAGE The MC275 operates on any line voltage be- tween 105 volts and 130 volts, 50 cycles to 60 cycles. The switch marked LINE VOLTAGE changes the tap on the primary of the power transformer. The switch can be adjusted at any time. INSTALLATION Adequate ventilation extends the trouble- free life of electronic instruments. It is generally found that each 10° centigrade (18° F) rise in temperature reduces the life of electrical insulation by one half. Adequate ventilation is an inexpensive and effective means of preventing insulation breakdown that results from unnecessarily high operat- ing temperatures. The direct benefit of ade- quate ventilation is longer, trouble-free life. The suggested minimum space for mount- ing the MC275 is 20" long x 14" wide x 10" high. Always allow for air flow either by ventilation holes or space next to the bottom of the amplifier and a means for the warm air to escape at the top. The MC275 can be mounted in any posi- tion except upside down. If the amplifier is to be installed on a vertical surface it is recom- mended that the transformers be on the down side. The advantage of this position is that the flow of heat from the tubes rises vertically and does not tend to heat the transformers. If the MC275 is to be permanently mounted use the two mounting flanges supplied with the amplifier. The flanges are shipped sepa- rately and must be attached to the amplifier bottom at each end. Turn the MC275 over with the transform- ers down and place it on a piece of cloth or cardboard to prevent scratches. The ampli- fier is shipped with 4 plastic feet on the bot- tom cover. Remove the 4 plastic feet. Re- move the three self tapping screws at one end of the amplifier that hold the bottom cover to the chromium chassis. Place the square edge of the mounting flange with the three round holes positioned over the three holes in the bottom cover. The three holes in the mounting flange will line up over the three holes in the chassis. Replace the three self tapping screws through the mounting flange and bottom cover. The mounting flange is now firmly attached to the ampli- fier. The mounting flange on the other end of the amplifier is installed in the same way. Fig. 4—Bottom of MC275 with mounting flanges attached. Place the MC275 mounting template on the area where the amplifier is to be mounted. Center punch the mounting shelf through the 4 slotted holes in the mounting flanges shown on the template. Remove the template and install four #10 round head screws in the center punch marks. Do not tighten these screws. Place the amplifier over the screw heads and slide the amplifier to either side in the slotted holes of the mounting flanges. The # 10 wood screws can then be tightened securely. CONNECTING THE MC275 INPUT-STEREO The shielded cable from the left output of the Mclntosh preamplifier is plugged into the jack marked STEREO INPUT-L The shielded cable from the right output of the Mclntosh preamplifier is plugged into the jack marked STEREO INPUT-R. INPUT-TWIN AMP The shielded cable from the left program source is plugged into the jack marked TWIN INPUT-L The shielded cable from the right program source is plugged into the jack marked TWIN INPUT-R. INPUT-MONO The shielded cable from the program source is plugged into the jack marked MONO INPUT. OUTPUT-STEREO OR TWIN AMPLIFIERS For stereo or twin channel operation it is not necessary to use the same impedance load on each output. Simply connect each output for the impedance desired. 5 Warning: Do not parallel the amplifier out- puts when using the amplifier as a stereo amplifier or twin channel amplifier. Damage to the output tubes may result if parallel operation is attempted when the output volt- ages are not the same phase and amplitude. Speakers are connected at the barrier strips marked OUTPUT on the left end of the panel. In compliance with the National Electrical Code, Class II wiring can be used between the speaker and the amplifier at the 4 ohm, 8 ohm, or 16 ohm connection. Class II wiring is lamp cord, bell wire, or other wire with this type of insulation. For the normally short distances of under 100 feet between the amplifier and speaker, #18 wire or larger can be used. For distances over 100 feet between the amplifier and speaker use larger wire. The loudspeaker impedance is usually identified on the loudspeaker itself. Connect one of the leads from the left loudspeaker to the screw marked COM on the left barrier strip. Connect the other lead from the left loudspeaker to the screw marked with the number corresponding to the speaker im- pedance on the LEFT barrier strip. If the speaker impedance is: 4 ohms 8 ohms 16 ohms Connect one left speaker lead to screw LEFT-COM and the other to: LEFT-4 LEFT-8 LEFT-16 Connect one right speaker lead to the screw marked RIGHT-COM and the other to: RIGHT-4 RIGHT-8 RIGHT-16 The only adverse effect on the operation of a Mclntosh amplifier when it is improperly matched is a reduction in the amount of distortion-free power available to the loud- speaker. Close impedance matching is de- sirable for maximum distortion-free power. Use this table to determine proper speaker connections: OUTPUT-MONOPHONIC When the MC275 is to operate as a 150 watt monophonic amplifier, the outputs of the two channels combine to produce a single 150 watt output. This chart lists the proper connections and interconnections for monophonic operation. If the speaker impedance is: 2 ohms 4 ohms 8 ohms 16 ohms 32 ohms Connect one speaker lead to the screw marked LEFT-COM and the other to: LEFT-4 LEFT-8 LEFT-16 RIGHT-8 RIGHT-16 Connect a wire between: LEFT-COM and RIGHT-COM LEFT-COM and RIGHT-COM LEFT-COM and RIGHT-COM RIGHT-COM and LEFT-8 RIGHT-COM and LEFT-16 Connect another wire between: LEFT-4 and RIGHT-4 LEFT-8 and RIGHT-8 LEFT-16 and RIGHT-16 — — When connected as outlined the MC275 operates as a 150 watt monophonic amplifier. LINE OUTPUT-STEREO or TWIN AMPLIFIERS The octal socket marked LINE OUTPUT has connections for 70.7 volts, 115 volts and 600 ohms. The 25 volt line is fed from the barrier strips. For 25 volt line operation connect one of the left leads to the screw marked COM on the LEFT barrier strip. The other left lead is connected to the screw marked 8 on the LEFT barrier strip. Connect the right leads in the same manner on the RIGHT barrier strip. The 67 ohm and 70.7 volt connections are the same. To connect for 67 ohm or 70.7 volt operation the octal plug supplied in the hardware bag is used. Solder one of the left leads to pin #7 and the other to pin #1. Solder one of the right leads to pin #8 and the other to pin #1. Pin #1 is the ground side. The 600 ohm connections for the left side are made between pin #2 and pin #3. The 600 ohm connections for the right side are made between pin #4 and pin #5. The 600 ohm winding is balanced to ground. Pin #1 on the octal socket is the center tap of the 600 winding. Pin #1 is grounded. For all applications using 600 ohms use Class I wiring if the installation must meet the requirements of the National Electrical Code. LINE OUTPUT-MONOPHONIC The octal socket marked LINE OUTPUT has connections for operating the MC275 monophonically at 70.7 volts, 115 volts or 300 ohms. For operating at 25 volts connec- tions are made at the barrier strips. To feed a 25-volt line, connect one side to the screw marked COM on the LEFT barrier strip. Connect the other side to the screw marked 8 on the LEFT barrier strip. Then connect with a wire the screw marked COM on the LEFT barrier strip to the screw marked If the speaker impedance is between: 3.2 to 6.5 ohms 6.5 to 13 ohms 13 to 26 ohms Connect the speaker leads between COM and: 4 ohms 8 ohms 16 ohms 6 COM on the RIGHT barrier strip. Connect, with another wire, the screw marked 8 on the LEFT barrier strip to the screw marked 8 on the RIGHT barrier strip. The 34 ohm and the 70.7 volt connec- tions are the same. To connect for 34 ohms or 70.7 volts solder one of the leads to pin #1 in the octal socket. The other lead is soldered to pin #7. A wire is connected be- tween pin #7 and pin #8. For 150 watt monophonic operation 70.7 volts is available from the secondary of the output transformers, isolated from ground. Connect one lead to the terminal strip screw marked LEFT-COM and the other lead to the screw marked RIGHT-16. Connect a wire between RIGHT-COM and LEFT-16. To connect for 300 ohms one lead is soldered to pin #2. The other lead is sol- dered to pin #3. Connect pin #2 to pin #4 with a wire. With another wire connect pin #3 to pin #5. Pin #1 is the center tap of the 300 ohm winding. The 300 ohm winding is balanced to ground. AC POWER The MC275 operates on 105 volt to 130 volt, 50 to 60 cycle power. The amplifier will be turned on and off if its power cord is plugged in one of the auxiliary AC outlets on the program source. OPERATING THE MC275 Before turning the MC275 on check all connections and plugs to see that they are firmly and correctly connected. Check to make sure that the tubes are firmly seated in the proper sockets. After the following adjustments have been completed the MC- 275 will operate without any further attention. ADJUSTMENTS LINE VOLTAGE The LINE VOLTAGE switch should be set to the position that more closely matches the average line voltage in your area. The local electric power company can usually tell you the average line voltage in your area. If the line voltage is between 105 volts and 120 volts put the LINE VOLTAGE switch in the 117 volt position. If the line voltage is between 120 volts and 130 volts put the switch in the 125 volt position. If the line voltage is un- known, it is safer to operate with the switch in the 125 volt position. INPUT SWITCH STEREO With the input switch in the left position marked STEREO the input of the MC275 is connected to the two jacks marked STEREO INPUT located below the BALANCE control. The amplifier has an input sensitivity in this position of 2.0 volts. This position has been provided to be used with Mclntosh preampli- fiers or any other high output preamplifiers. The BALANCE control assists in balancing the overall stereo system for equal loudness. Equal loudness is affected by room acous- tics, furniture placement, speakers and many other things. With a monophonic signal adjust this control until both loudspeakers are equal in sound output. TWIN AMP With the input switch in the center posi- tion marked TWIN AMP, the input of the MC275 is connected to the two jacks marked TWIN INPUT located below the two center control knobs marked GAIN. The input sensi- tivity in this position is 0.5 volt. This position has been provided for use with a low output stereo preamplifier, an electronic crossover network, or as two completely separated monophonic 75 watt amplifiers. The two center control knobs marked GAIN should be adjusted to match the input sensitivity of the MC275 to the output voltage of the program source equipment. To balance a stereo system using the TWIN AMP input position use a monophonic signal from the program source. A mono- phonic signal supplies the same voltage to both channels. Turn the volume control on the source equipment to the 12 o'clock posi- tion (half rotation). Turn up the GAIN con- trol on the LEFT input until the loudness in the room is not quite as loud as you like to listen. Then turn the GAIN control on the RIGHT input until it is equally as loud as the left channel. The system is now balanced for loudness and provides the most convenient amount of loudness change when using the volume control on the source equipment. MONO With the switch in the right position marked MONO the inputs of the MC275 are internally connected in parallel to the jack 7 marked MONO INPUT. This jack is located below the right control knob marked GAIN. The input sensitivity in this position is 0.5 volt. The GAIN control should be adjusted to match the input voltage sensitivity of the MC275 to the output voltage of the program source. For maximum flexibility set the GAIN con- trol as follows: turn the volume control on the program source equipment (i.e. tape recorder, tuner, preamplifier, etc.) to the 12 o'clock (half rotation) position. Turn the GAIN control on the MC275 until the loud- ness of the sound from the speaker is just a little louder than you normally like to listen. The volume control on the program source equipment now has the most convenient amount of loudness change in either direc- tion from the 12 o'clock position. IMPORTANT The excellent performance that is inher- ent in all Mclntosh amplifiers does not depend on the critical adjustment of bias or balance controls in the output circuit. The patented Mclntosh circuit delivers its adver- tised specifications without any need for these controls and is not dependent on care- fully balanced tubes for its performance. With Mclntosh you can install the amplifier and forget it. The MC275 you have purchased will give you years of pleasant and satisfactory per- formance. If you have any questions con- cerning the operation or maintenance of this amplifier please contact: Customer Service Mclntosh Laboratory, Inc. 2 Chambers Street Binghamton, New York Our telephone number is 723-5491. The direct dial area code is 607. GUARANTEE Mclntosh Laboratory Incorporated guar- antees this equipment to perform as adver- tised. We also guarantee the mechanical and electrical workmanship and components of this equipment to be free of defects for a period of 90 days from date of purchase. This guarantee does not extend to compo- nents damaged by improper use nor does it extend to transportation to and from the factory. 3-YEAR FACTORY SERVICE CONTRACT An application for a FREE 3-YEAR FAC- TORY SERVICE CONTRACT is included in the pocket in the back cover of this manual. The FREE 3-YEAR FACTORY SERVICE CONTRACT will be issued by Mclntosh Laboratory upon receipt of the completely filled out applica- tion form. The term of this contract is defined in the 3-year factory service contract. If the application is not mailed to Mclntosh Labo- ratory only the services offered under the standard 90-day guarantee will apply on this equipment. TAKE ADVANTAGE OF 3 YEARS OF FREE FACTORY SERVICE BY FILLING IN THE APPLICATION NOW. In Canada: Manufactured under license by: McCurdy Radio Industries, Ltd. 22 Front Street West Toronto, Canada Design subject to change without notice. 8 LABORATORY, INC. 2 CHAMBERS STREET, BINGHAMTON, N. Y. Made In U.S.A. Phone-Area Code 607-723-5491