Yamaha Stage Keyboard (Model CK88, CK61)

Manual text content

English Français Español CK88 CK61 Owner’s Manual S2 (529-M02 FCC sdoc YCA 01) COMPLIANCE INFORMATION STATEMENT (Supplier ʼ s declaration of conformity procedure) Responsible Party: Yamaha Corporation of America Address: 6600 Orangethorpe Ave., Buena Park, Calif. 90620 Telephone: 714-522-9011 Type of Equipment: STAGE KEYBOARD Model Name: CK88, CK61 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received including interference that may cause undesired operation. 1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT! This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product. 2. IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables. Cable/s supplied with this product MUST be used. Follow all installation instructions. Failure to follow instructions could void your FCC authorization to use this product in the USA. 3. NOTE: This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class “B” digital devices. Compliance with these requirements provides a reasonable level of assurance that your use of this product in a residential environment will not result in harmful interference with other electronic devices. This equipment generates/uses radio frequencies and, if not installed and used according to the instructions found in the users manual, may cause interference harm- ful to the operation of other electronic devices. Compliance with FCC regulations does not guarantee that interference will not occur in all installations. If this product is found to be the source of interference, which can be determined by turning the unit “OFF” and “ON”, please try to eliminate the problem by using one of the following measures: - Relocate either this product or the device that is being affected by the interference. - Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC line filter/s. - In the case of radio or TV interference, relocate/reorient the antenna. If the antenna lead-in is 300 ohm ribbon lead, change the lead-in to co-axial type cable. If these corrective measures do not produce satisfactory results, please contact the local retailer authorized to distribute this type of product. If you cannot locate the appropriate retailer, please contact Yamaha Corporation of America, 6600 Orangethorpe Ave., Buena Park, CA90620, USA. The above statements apply ONLY to those products distributed by Yamaha Corporation of America or its subsidiaries. (529-M04 FCC class B YCA 01) FCC INFORMATION (U.S.A.) CK88 CK61 Owner’s Manual S3 For AC adaptor Explanation of Graphical Symbols The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. IMPORTANT SAFETY INSTRUCTIONS 1 Read these instructions. 2 Keep these instructions. 3 Heed all warnings. 4 Follow all instructions. 5 Do not use this apparatus near water. 6 Clean only with dry cloth. 7 Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8 Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9 Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 10 Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 11 Only use attachments/accessories specified by the manufacturer. 12 Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/ apparatus combination to avoid injury from tip-over. 13 Unplug this apparatus during lightning storms or when unused for long periods of time. 14 Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. (502-M01 UL 60065-1 en 01) CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE. CK88 CK61 Owner’s Manual S4 (58-M03 WEEE battery en 01) Information for users on collection and disposal of old equipment and used batteries: These symbols on the products, packaging, and/or accompanying documents mean that used electrical and electronic products and batteries should not be mixed with general household waste. For proper treatment, recovery and recycling of old products and used batteries, please take them to applicable collection points, in accordance with your national legislation. By disposing of these products and batteries correctly, you will help to save valuable resources and prevent any potential negative effects on human health and the environment which could otherwise arise from inappropriate waste handling. For more information about collection and recycling of old products and batteries, please contact your local municipality, your waste disposal service or the point of sale where you purchased the items. For business users in the European Union: If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further information. Information on Disposal in other Countries outside the European Union: These symbols are only valid in the European Union. If you wish to discard these items, please contact your local authorities or dealer and ask for the correct method of disposal. Note for the battery symbol (bottom symbol example): This symbol might be used in combination with a chemical symbol. In this case it complies with the requirement set by the EU Battery Directive for the chemical involved. The model number, serial number, power requirements, etc., may be found on or near the name plate, which is at the bottom of the unit. You should note this serial number in the space provided below and retain this manual as a permanent record of your purchase to aid iden- tification in the event of theft. Model No. Serial No. (1003-M06 plate bottom en 01) For Singapore Users are only allowed to use EN 50075 detachable and interchangeable 2-pin plugs or BS 1363-3 or SS 145-3 detachable and interchangeable 3-pin plugs that are approved and suitable to use in Singapore. (604-M02 SG adaptor 01) CK88 CK61 Owner’s Manual S5 (554-M01) (554-M03 FCC mobile SAR 01) (555-M04 ISED mobile SAR en 01) (555-M13 ISED RSS en 01) This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines. This equipment should be installed and operated keeping the radiator at least 20 cm or more away from person ʼ s body. This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment and meets RSS-102 of the ISED radio frequency (RF) Exposure rules. This equipment should be installed and operated keeping the radiator at least 20 cm or more away from person’s body. This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device must accept any interference, including interference that may cause undesired operation of the device. EN SIMPLIFIED EU DECLARATION OF CONFORMITY / SIMPLIFIED UK DECLARATION OF CONFORMITY Hereby, Yamaha Music Europe GmbH declares that the radio equipment type [CK88, CK61] is in compliance with Directive 2014/53/ EU and the radio equipment regulations of UK. The full texts of the EU declaration of conformity and the UK declaration of conformity are available at the following internet address: https://europe.yamaha.com/en/support/compliance/doc.html FR DECLARATION UE DE CONFORMITE SIMPLIFIEE Le soussigné, Yamaha Music Europe GmbH, déclare que l'équipement radioélectrique du type [CK88, CK61] est conforme à la directive 2014/53/UE. Le texte complet de la déclaration UE de conformité est disponible à l'adresse internet suivante : https://europe.yamaha.com/en/support/compliance/doc.html DE VEREINFACHTE EU-KONFORMITÄTSERKLÄRUNG Hiermit erklärt Yamaha Music Europe GmbH, dass der Funkanlagentyp [CK88, CK61] der Richtlinie 2014/53/EU entspricht. Der vollständige Text der EU-Konformitätserklärung ist unter der folgenden Internetadresse verfügbar: https://europe.yamaha.com/en/support/compliance/doc.html SV FÖRENKLAD EU-FÖRSÄKRAN OM ÖVERENSSTÄMMELSE Härmed försäkrar Yamaha Music Europe GmbH att denna typ av radioutrustning [CK88, CK61] överensstämmer med direktiv 2014/ 53/EU. Den fullständiga texten till EU-försäkran om överensstämmelse finns på följande webbadress: https://europe.yamaha.com/en/support/compliance/doc.html IT DICHIARAZIONE DI CONFORMITÀ UE SEMPLIFICATA Il fabbricante, Yamaha Music Europe GmbH, dichiara che il tipo di apparecchiatura radio [CK88, CK61] è conforme alla direttiva 2014/ 53/UE. Il testo completo della dichiarazione di conformità UE è disponibile al seguente indirizzo Internet: https://europe.yamaha.com/en/support/compliance/doc.html ES DECLARACIÓN UE DE CONFORMIDAD SIMPLIFICADA Por la presente, Yamaha Music Europe GmbH declara que el tipo de equipo radioeléctrico [CK88, CK61] es conforme con la Directiva 2014/53/UE. El texto completo de la declaración UE de conformidad está disponible en la dirección Internet siguiente: https://europe.yamaha.com/en/support/compliance/doc.html PT DECLARAÇÃO UE DE CONFORMIDADE SIMPLIFICADA O(a) abaixo assinado(a) Yamaha Music Europe GmbH declara que o presente tipo de equipamento de rádio [CK88, CK61] está em conformidade com a Diretiva 2014/53/UE. O texto integral da declaração de conformidade está disponível no seguinte endereço de Internet: https://europe.yamaha.com/en/support/compliance/doc.html NL VEREENVOUDIGDE EU-CONFORMITEITSVERKLARING Hierbij verklaar ik, Yamaha Music Europe GmbH, dat het type radioapparatuur [CK88, CK61] conform is met Richtlijn 2014/53/EU. De volledige tekst van de EU-conformiteitsverklaring kan worden geraadpleegd op het volgende internetadres: https://europe.yamaha.com/en/support/compliance/doc.html CK88 CK61 Owner’s Manual S6 BG ОПРОСТЕНА ЕС ДЕКЛАРАЦИЯ ЗА СЪОТВЕТСТВИЕ С настоящото Yamaha Music Europe GmbH декларира , че този тип радиосъоръжение [CK88, CK61] е в съответствие с Директива 2014/53/ ЕС . Цялостният текст на ЕС декларацията за съответствие може да се намери на следния интернет адрес : https://europe.yamaha.com/en/support/compliance/doc.html CS ZJEDNODUŠENÉ EU PROHLÁŠENÍ O SHOD Ě Tímto Yamaha Music Europe GmbH prohlašuje, že typ rádiového za ř ízení [CK88, CK61] je v souladu se sm ě rnicí 2014/53/EU. Úplné zn ě ní EU prohlášení o shod ě je k dispozici na této internetové adrese: https://europe.yamaha.com/en/support/compliance/doc.html DA FORENKLET EU-OVERENSSTEMMELSESERKLÆRING Hermed erklærer Yamaha Music Europe GmbH, at radioudstyrstypen [CK88, CK61] er i overensstemmelse med direktiv 2014/53/EU. EU-overensstemmelseserklæringens fulde tekst kan findes på følgende internetadresse: https://europe.yamaha.com/en/support/compliance/doc.html ET LIHTSUSTATUD ELI VASTAVUSDEKLARATSIOON Käesolevaga deklareerib Yamaha Music Europe GmbH, et käesolev raadioseadme tüüp [CK88, CK61] vastab direktiivi 2014/53/EL nõuetele. ELi vastavusdeklaratsiooni täielik tekst on kättesaadav järgmisel internetiaadressil: https://europe.yamaha.com/en/support/compliance/doc.html EL ΑΠΛΟΥΣΤΕΥΜΕΝΗ ΔΗΛΩΣΗ ΣΥΜΜΟΡΦΩΣΗΣ ΕΕ Με την παρούσα ο / η Yamaha Music Europe GmbH, δηλώνει ότι ο ραδιοεξοπλισμός [CK88, CK61] πληροί την οδηγία 2014/53/ ΕΕ . Το πλήρες κείμενο της δήλωσης συμμόρφωσης ΕΕ διατίθεται στην ακόλουθη ιστοσελίδα στο διαδίκτυο : https://europe.yamaha.com/en/support/compliance/doc.html HR POJEDNOSTAVLJENA EU IZJAVA O SUKLADNOSTI Yamaha Music Europe GmbH ovime izjavljuje da je radijska oprema tipa [CK88, CK61] u skladu s Direktivom 2014/53/EU. Cjeloviti tekst EU izjave o sukladnosti dostupan je na sljede ć oj internetskoj adresi: https://europe.yamaha.com/en/support/compliance/doc.html LV VIENK Ā RŠOTA ES ATBILST Ī BAS DEKLAR Ā CIJA Ar šo Yamaha Music Europe GmbH deklar ē , ka radioiek ā rta [CK88, CK61] atbilst Direkt ī vai 2014/53/ES. Pilns ES atbilst ī bas deklar ā cijas teksts ir pieejams š ā d ā interneta vietn ē : https://europe.yamaha.com/en/support/compliance/doc.html LT SUPAPRASTINTA ES ATITIKTIES DEKLARACIJA Aš, Yamaha Music Europe GmbH, patvirtinu, kad radijo į rengini ų tipas [CK88, CK61] atitinka Direktyv ą 2014/53/ES. Visas ES atitikties deklaracijos tekstas prieinamas šiuo interneto adresu: https://europe.yamaha.com/en/support/compliance/doc.html HU EGYSZER Ű SÍTETT EU-MEGFELEL Ő SÉGI NYILATKOZAT Yamaha Music Europe GmbH igazolja, hogy a [CK88, CK61] típusú rádióberendezés megfelel a 2014/53/EU irányelvnek. Az EU- megfelel ő ségi nyilatkozat teljes szövege elérhet ő a következ ő internetes címen: https://europe.yamaha.com/en/support/compliance/doc.html PL UPROSZCZONA DEKLARACJA ZGODNO Ś CI UE Yamaha Music Europe GmbH niniejszym o ś wiadcza, ż e typ urz ą dzenia radiowego [CK88, CK61] jest zgodny z dyrektyw ą 2014/53/ UE. Pe ł ny tekst deklaracji zgodno ś ci UE jest dost ę pny pod nast ę puj ą cym adresem internetowym: https://europe.yamaha.com/en/support/compliance/doc.html RO DECLARA Ț IA UE DE CONFORMITATE SIMPLIFICAT Ă Prin prezenta, Yamaha Music Europe GmbH declar ă c ă tipul de echipamente radio [CK88, CK61] este în conformitate cu Directiva 2014/53/UE. Textul integral al declara ț iei UE de conformitate este disponibil la urm ă toarea adres ă internet: https://europe.yamaha.com/en/support/compliance/doc.html SK ZJEDNODUŠENÉ EÚ VYHLÁSENIE O ZHODE Yamaha Music Europe GmbH týmto vyhlasuje, že rádiové zariadenie typu [CK88, CK61] je v súlade so smernicou 2014/53/EÚ. Úplné EÚ vyhlásenie o zhode je k dispozícii na tejto internetovej adrese: https://europe.yamaha.com/en/support/compliance/doc.html CK88 CK61 Owner’s Manual S7 (559-M01 RED DoC URL 02) SL POENOSTAVLJENA IZJAVA EU O SKLADNOSTI Yamaha Music Europe GmbH potrjuje, da je tip radijske opreme [CK88, CK61] skladen z Direktivo 2014/53/EU. Celotno besedilo izjave EU o skladnosti je na voljo na naslednjem spletnem naslovu: https://europe.yamaha.com/en/support/compliance/doc.html FI YKSINKERTAISTETTU EU-VAATIMUSTENMUKAISUUSVAKUUTUS Yamaha Music Europe GmbH vakuuttaa, että radiolaitetyyppi [CK88, CK61] on direktiivin 2014/53/EU mukainen. EU- vaatimustenmukaisuusvakuutuksen täysimittainen teksti on saatavilla seuraavassa internetosoitteessa: https://europe.yamaha.com/en/support/compliance/doc.html TR BAS İ TLE Ş T İ R İ LM İŞ AVRUPA B İ RL İĞİ UYGUNLUK B İ LD İ R İ M İ İş bu belge ile, Yamaha Music Europe GmbH, radyo cihaz tipinin [CK88, CK61], Direktif 2014/53/ AB'ye uygunlu ğ unu beyan eder. AB uyumu beyan ı n ı n tam metni a ş a ğ ı daki internet adresinden edinilebilir: https://europe.yamaha.com/en/support/compliance/doc.html CK88 CK61 Owner’s Manual 2 PRECAUTIONS PLEASE READ CAREFULLY BEFORE PROCEEDING Please keep this manual in a safe and handy place for future reference. WARNING Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical shock, short-circuiting, damages, fire or other hazards. These precautions include, but are not limited to, the following: Power supply • Do not place the power cord near heat sources such as heaters or radiators. Also, do not excessively bend or otherwise damage the cord, or place heavy objects on it. • Do not touch the product or the power plug during an electrical storm. • Use only the correct voltage specified for the product. The required voltage is printed on the name plate of the product. • Use the specified adaptor (page 69). • Check the power plug periodically and remove any dirt or dust which may have accumulated on it. • Insert the power plug firmly all the way into the AC outlet. Using the product when it is not plugged in sufficiently can cause dust to accumulate on the plug, possibly resulting in fire or skin burns. • When setting up the product, make sure that the AC outlet you are using is easily accessible. If some trouble or malfunction occurs, immediately turn off the power switch and disconnect the plug from the outlet. Even when the power switch is turned off, as long as the power cord is not unplugged from the wall AC outlet, the product will not be disconnected from the power source. • Do not connect the product to an electrical outlet using a multi-plug outlet extender. Doing so can result in lower sound quality, or possibly cause overheating in the outlet. • When disconnecting the power plug, always hold the plug itself and not the cord. Pulling by the cord can damage it and cause electric shocks or a fire. • If not using the product for long periods of time, be sure to pull the power plug from the AC outlet. Do not disassemble • Do not attempt to disassemble the internal parts or modify them in any way. Water warning • Do not expose the product to rain, use it near water or in damp or wet conditions, or place on it any containers (such as vases, bottles or glasses) containing liquids which might spill into any openings or places where water may drop. A liquid such as water getting into the product may cause a fire, electric shocks, or malfunctions. • Use the AC adaptor indoors only. Do not use in any wet environments. • Never insert or remove a power plug with wet hands. Fire warning • Do not place any burning items or open flames near the product, since they may cause a fire. Wireless unit • Radio waves from this product may affect electro-medical devices, such as a heart pacemaker implant or defibrillator implant. - Do not use the product near medical devices or inside medical facilities. Radio waves from this product may affect electro-medical devices. - Do not use the product within 15 cm (6 in.) of persons with a heart pacemaker implant or a defibrillator implant. Handling • Magnetism from this product may affect electro-medical devices, such as a heart pacemaker implant or defibrillator implant. - Keep the product away from a heart pacemaker implant or a defibrillator implant. Batteries • Do not dispose of a battery in a fire. • Do not expose the battery to conditions of extreme low air pressure, cold or heat (such as in direct sunlight or a fire) or excessive dust or humidity. Doing so may result in the battery bursting, causing a fire or injury. • Follow the precautions below. Failure to do so might result in battery fluid leakage. If the contents of the battery gets on your hands or in your eyes, it can cause blindness, chemical burns, and damage of the product. - Use the specified battery type (page 69) only. - Do not use new batteries together with old ones. - Do not mix battery types. - Always make sure all batteries are inserted in conformity with the +/- polarity markings. - Do not disassemble a battery. (DMI-10) 1/2 CK88 CK61 Owner’s Manual 3 - When the batteries run out, or if the product is not to be used for a long time, remove the batteries from the product. - Do not attempt to recharge batteries that are not designed to be charged. • If the batteries do leak, avoid contact with the leaked fluid. If the battery fluid should come in contact with your eyes, mouth, or skin, wash immediately with water and consult a doctor. Battery fluid is corrosive and may possibly cause loss of sight or chemical burns. • When using rechargeable batteries, follow the instructions that came with the batteries. Use only the specified charger device and within the specified charging temperature range when charging. Charging with an unspecified charger or at a temperature outside the range may cause leakage, overheating, explosion, or malfunction. • Keep batteries away from children. A child could accidentally swallow a battery. Failure to observe this may also cause inflammation due to battery fluid leaks. • Do not put batteries in a pocket or bag, or carry or store them together with pieces of metal. Batteries kept in such condition could short, burst, or leak, causing a fire or injury. If you notice any abnormality • If any of the following problems occur, immediately turn off the power switch and disconnect the power plug from the outlet. If you are using batteries, remove all batteries from the product. Finally have the device inspected by Yamaha service personnel. - The power cord or plug becomes frayed or damaged. - Unusual smells or smoke are emitted. - Some object, or water has been dropped into the product. - There is a sudden loss of sound during use of the product. - Cracks or other visible damage appear on the product. CAUTION Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage to the product or other property. These precautions include, but are not limited to, the following: Location • Do not place the product in an unstable position or a location with excessive vibration, where it might accidentally fall over and cause injury. Connections • Before connecting the product to other electronic components, turn off the power for all components. Before turning the power on or off for all components, set all volume levels to minimum. • Be sure to set the volumes of all components at their minimum levels and gradually raise the volume controls while playing the product to set the desired listening level. Handling • Do not insert foreign materials such as metal or paper into any openings or gaps of the product. Failure to observe this may cause a fire, electric shocks, or malfunctions. • Do not rest your weight on, or place heavy objects on the product, and do not use excessive force on the buttons, switches or connectors. • Do not use the product or headphones for a long period of time at a high or uncomfortable volume level, since this can cause permanent hearing loss. If you experience any hearing loss or ringing in the ears, consult a physician. • Remove the power plug from the AC outlet before cleaning the unit. Failure to observe this may cause electric shocks. Yamaha cannot be held responsible for damage caused by improper use or modifications to the product, or data that is lost or destroyed. Always turn the power off when the product is not in use. Even when the [ ] (Standby/On) switch is in standby status (display is off), electricity is still flowing to the product at the minimum level. When you are not using the product for a long time, make sure you unplug the power cord from the wall AC outlet. Make sure to discard used batteries according to local regulations. (DMI-10) 2/2 CK88 CK61 Owner’s Manual 4 NOTICE To avoid the possibility of malfunction/ damage to the product, damage to data, or damage to other property, follow the notices below.  Handling • Do not use the instrument in the vicinity of a TV, radio, stereo equipment, mobile phone, or other electric devices. Otherwise, the instrument, TV, or radio may generate noise. • When you use the instrument along with an app on your smart devices, such as a smartphone or tablet, we recommend that you enable “Airplane Mode” on the device to avoid noise caused by communication. When turning on airplane mode, Bluetooth® settings may be turned off. Make sure that the setting is turned on before use. • Depending on the condition of surrounding radio waves, the instrument may possibly malfunction. • Do not expose the instrument to excessive dust or vibrations, or extreme cold or heat (such as in direct sunlight, near a heater, or in a car during the day) to prevent the possibility of disfiguration, damage to the internal components, or unstable operation. • Do not place vinyl, plastic, or rubber objects on the instrument, since this might discolor the instrument.  Maintenance • When cleaning the instrument, use a soft and dry/slightly damp cloth. Do not use paint thinners, solvents, alcohol, cleaning fluids, or chemical-impregnated wiping cloths.  Saving settings • Edited settings are lost when you turn off the power to the instrument. This also occurs when the power is turned off by the Auto Power Off function (page 22). Save the settings to the instrument, or a USB flash drive (page 27). However, the settings saved to the instrument may be lost due to some failure, an operation mistake, etc. Save your important settings onto a USB flash drive (page 27). Before using a USB flash drive, make sure to refer to page 23. • To protect against settings loss through USB flash drive damage, we recommend that you save your important settings onto a spare USB flash drive as a backup file. Information  About copyrights The copyright of the “content” *1 installed in this product belongs to Yamaha Corporation or its copyright holder. Except as permitted by copyright laws and other relevant laws, such as copying for personal use, it is prohibited to “reproduce or divert” *2 without the permission of the copyright holder. When using the content, consult with a copyright expert. If you create music or perform with the contents through the original use of the product, and then record and distribute them, the permission of Yamaha Corporation is not required regardless of whether the distribution method is paid or free of charge. *1: The word “content” includes a computer program, audio data, Accompaniment Style data, MIDI data, waveform data, voice recording data, music score, and score data, etc. *2: The phrase “reproduce or divert” includes taking out the content itself in this product, or recording and distributing it without changes in a similar manner.  About this manual • The illustrations and LCD screens as shown in this manual are for instructional purposes only. • Unless indicated otherwise, the illustrations and displays as shown in this manual are based on the CK61 (in English). • iPhone and iPad are trademarks of Apple Inc., registered in the U.S. and other countries. • The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Yamaha Corporation is under license. • The company names and product names in this manual are the trademarks or registered trademarks of their respective companies.  About disposal When disposing of this product, please contact the appropriate local authorities.  Firmware To implement new functions and improve operability, this keyboard may be shipped with an updated version of the firmware installed. A set of manuals for the updated version of the firmware can be downloaded from the website below. Yamaha Downloads: https://download.yamaha.com/ The firmware version of your keyboard can be checked from [MENU]  Version Info . CK88 CK61 Owner’s Manual 5 MEMO CK88 CK61 Owner‘s Manual 6 Thank you for purchasing this Yamaha CK88 or CK61 Stage Keyboard! As the name implies, it is an instrument designed especially for live performance. With its high-quality sounds and comprehensive features, the CK is ideal in an exceptionally wide range of situations—from live venues, both indoors and outdoors, to studio rehearsal and recording, as well as practice and enjoyment at home. We recommend that you read this manual carefully so that you can fully take advantage of the advanced and convenient functions of the CK. We also recommend that you keep this manual in a safe and handy place for future reference.  Owner’s Manual (this book) × 1  AC adaptor (PA-150B) × 1 Welcome Accessories CK88 CK61 Owner’s Manual 7 PRECAUTIONS ............................................................................. 2 NOTICE........................................................................................... 4 Information .................................................................................. 4 Welcome 6 Accessories 6 About the CK88 and CK61 8 Main features............................................................................... 8 Basic structure............................................................................. 8 Sound management system.................................................. 9 Panel controls 10 Front panel ................................................................................10 Rear panel ..................................................................................18 Setting up 20 Using an AC adaptor...............................................................20 Using batteries..........................................................................21 Turning the power on ............................................................22 Turning the power off ............................................................22 Setting the Auto Power Off function................................22 Connecting headphones ......................................................22 Using a USB flash drive ..........................................................23 Basic operations 24 Top screen configuration......................................................24 Creating a Live Set Sound.....................................................24 Saving the Live Set Sound ....................................................24 Other Live Set Sound features 25 Applying effects to audio signals from the A/D INPUT jacks ..............................................................................................25 Playing back an audio file .....................................................25 Managing Live Set Sounds 26 Editing Live Set Sound names.............................................26 Swapping or copying Live Set Sounds.............................26 Initializing a Live Set Sound .................................................26 Saving the Live Set Sound to a USB flash drive.............27 Changing a previously saved file name...........................27 Loading a Live Set Sound from a USB flash drive.........27 Advanced settings 28 Live Set (SETTINGS button) ..................................................28 Entire instrument (MENU button) .....................................36 Shortcut operations................................................................42 Effect list......................................................................................43 Using with External Devices 46 Precautions when using the USB [TO HOST] terminal ........................................................................................................46 Using Smart Devices...............................................................46 Connecting to a computer...................................................47 Controlling a synthesizer or tone generator module from the CK................................................................................47 Controlling the CK from an external keyboard.............48 Setting the MIDI transmit and receive channels..........48 Disabling the internal tone generator sound when the built-in keyboard is played ..................................................48 Setting how the MIDI terminals are used (MIDI Port settings) ......................................................................................48 Data List 49 Live Set Sound List ..................................................................49 Voice List.....................................................................................52 Control Change Number ......................................................54 MIDI Data Format ....................................................................56 MIDI Data Table........................................................................58 MIDI Implementation Chart.................................................64 Other information 66 Troubleshooting ......................................................................66 Display messages ....................................................................68 Specifications............................................................................69 Index.............................................................................................70 Contents CK88 CK61 Owner‘s Manual 8 Main features The CK88 and CK61 are stage keyboards that are ideal for a wide variety of applications and locations.  Uncompromising performance capabilities—on stage, in the studio, even outdoors • Loaded with authentic keyboard sounds such as pianos, electric pianos, and organs, as well as many other sounds crucial for contemporary keyboard performance. • Allows various combinations of three independent parts using layer and split functions, and features connectivity to an external keyboard, computer, or smartphone. • With its built-in stereo speakers and battery operation capability, you can use the CK virtually anywhere you want.  Intuitive controls for instant sound crafting • Features independent control sections for the filter, EG, and effects blocks. These are essential for dynamic sound-making, letting you tweak the sounds in real time as you perform. • Built-in drawbars exclusively for real-time Organ Voice control—just as on an actual vintage organ. • Single-button operation for enabling Portamento or unison sounds.  Extensive support functions for creative performance • Convenient A/D INPUT jacks let you connect a microphone, and use exclusive built-in effects for the input. This is useful for singing and playing the keyboard in rehearsal or in small-group performances. • Audio playback function via Bluetooth Audio connection enables performance along with playback of your favorite tunes or using background music from a Bluetooth-equipped device. • Since the CK88 and CK61 are USB-compatible, connection with a computer or a smartphone is extremely quick and easy—a significant timesaver when setting up for video recording and online live streaming. Basic structure The front panel of this keyboard is divided into three areas. Combining the settings in each of these areas gives you enormous flexibility in creating sounds. Select a Voice for each of the three keyboard Parts A to C, as well as the On/Off settings and volume balance of each Part, the keyboard split, and effect settings, and then save these settings. You can call up these settings freely as you play and perform. About the CK88 and CK61 Select a voice and combine voices Create and adjust the organ voice Applying sound effects About the CK88 and CK61 CK88 CK61 Owner‘s Manual 9 Sound management system The sound you create by combining these settings is managed through the Live Set function. Within each Live Set you can save a group of settings. One group of settings saved in the Live Set is called a “Live Set Sound.” Live Set Sounds can be switched instantly by using eight Live Set buttons on the front panel, even during a performance. Also, eight Live Set Sounds can be registered on a Live Set Page, and you can call up other Live Set Pages by pressing the PAGE buttons. There are 20 Live Set Pages, allowing you to use a total of 160 voices through this function. As a factory default, Live Set Pages 1 to 10 contain preset Live Set Sounds. Live Set Sounds can be saved to the internal memory of the keyboard or the USB flash drive, or through Soundmondo for backup and sharing. • Internal memory • USB flash drive • Soundmondo (sound management and sharing service) https://www.yamaha.com/2/soundmondo 1 2 3 4 5 6 7 8 Live Set Live Set Sound Live Set Page 20 pages Part A Part B Part C EQ REVERB DELAY SETTINGS CK88 CK61 Owner’s Manual 10 Front panel Pitch Bend Wheel For use as the Pitch Bend controller. The Pitch Bend range can be set from the [SETTINGS] button  Controllers  Pitch Bend Range for each Part (page 31). Modulation Wheel For applying modulation to the sound. The modulation can be applied to pitch, amplitude, or filter. You can change the Control Change number assigned to the wheel. Change the setting from the [SETTINGS] button  Controllers  Mod Wheel Assign (page 31). NOTE • Change the modulation depth and speed from the [SETTINGS] button  Sound  (Part)  Modulation (page 29). • Modulation can be assigned to a different controller. [MASTER VOLUME] slider For adjusting the overall volume of the CK. ROTARY [STOP] button For stopping the rotation effect of the rotary speaker. ROTARY [SPEED] button For changing the rotation speed of the rotary speaker. When the DRIVE is off, or the Drive Type other than Rotary A and Rotary B is selected, pressing the ROTARY [SPEED] button will activate the function and select Rotary A . TRANSPOSE buttons For adjusting the pitch of the entire keyboard in semitones. The value is transmitted as a MIDI message, but not saved for the Live Set Sound. Simultaneously press the [−] and [+] buttons to restore the value to “0.” NOTE Simultaneously press one of the TRANSPOSE buttons and the [ENTER] button to set the Sound Transpose for the Live Set Sound (page 42). The Sound Transpose setting is stored in a Live Set Sound. OCTAVE buttons For changing the range of the keyboard in octaves. The value is transmitted as a MIDI message, but not saved for the Live Set Sound. Simultaneously press the [−] and [+] buttons to restore the value to “0.” The octave setting can be set independently for each part by using the Note Shift function. Pressing the OCTAVE button while holding down the PART button will make the OCTAVE button light in the corresponding part color (page 42). The octave setting for the part ( Note Shift setting) can be stored in a Live Set Sound. Panel controls Panel controls CK88 CK61 Owner’s Manual 11 VIBRATO/CHORUS [ON/OFF] button VIBRATO/CHORUS [TYPE] button For setting the Vibrato/Chorus effects for the Organ voice. These buttons can be used when the Organ Voices using the Organ Flutes tone generator (H, V, F, A, and Y) are selected (page 13). Use the [ON/OFF] button to turn the Vibrato/Chorus effects on or off, and the [TYPE] button to select a vibrato or chorus type. Pressing the button alternates sequentially between V (vibrato) 1 to 3 and C (chorus) 1 to 3. NOTE Simultaneously press the [ENTER] and VIBRATO/CHORUS [TYPE] buttons to show the list of VIBRATO/CHORUS types in reverse order. This is convenient for selecting a previous type on the list (page 42). PERCUSSION [ON/OFF] button PERCUSSION [Soft] button PERCUSSION [Fast] button PERCUSSION [2nd 3rd] button For setting up the percussion sounds for Organ voice. These buttons can be used when the Organ Voices using the Organ Flutes tone generator (H, V, F, A, and Y) are selected. Use the [ON/OFF] button to turn the percussion sounds on or off, the [Soft] button to lower the volume, and the [Fast] button to set the faster decay speed for the Percussion sounds. Use the [2nd 3rd] button to change the pitch of the percussion sounds. ORGAN FOOTAGE sliders For setting the component elements of the Organ Voice. These sliders can be used only when the Organ Voices using the Organ Flutes tone generator (H, V, F, A, and Y) are selected. Just as with the drawbars on a vintage organ, moving the sliders downwards (toward you) increases the volume of the component elements to make the overall organ tone louder. To create the organ tone you desire, you can move each of these sliders to change the component elements of the sound. NOTE • No organ sound will be produced if all the ORGAN FOOTAGE sliders are moved up. • In many cases when calling up a setting from LIVE SET [1]–[8], the actual position of the sliders and the value of the setting do not match. Once you move a slider, its position is reflected in the settings. For changing the settings so that the values for the positions of all the sliders are immediately reflected in the settings without having to move the sliders, change the setting from the [MENU] button  General  Control Panel  Controller Mode (page 39). Panel controls CK88 CK61 Owner’s Manual 12 The component tones produced by moving each of the sliders are shown below. Part Volume Sliders For setting the volume for each Part. Part [ON/OFF] buttons For switching each Part on or off. Part [A]–[C] select buttons For selecting the desired Part for changing the settings. When the Part is enabled here, you can control the following settings from the front panel. • Voice category selection • Organ voice settings • MONO and UNISON settings • Filter • EG • Drive • Effect1 and Effect2 By pressing multiple Part select buttons, you can set the same filter and effects for those selected Parts at once. NOTE By simultaneously holding down two of the Part select buttons, you can swap the settings for those Parts (page 42). This is convenient when you wish to switch the right- and left-hand Parts for the Split setting. Display (LCD) For displaying the system messages, parameter settings, and other information depending on the function currently being used. [SETTINGS] button For calling up the screens for making detailed settings for the currently selected Live Set Sound (page 28). You can make various settings, including the Part sound and controller customizations, Audio Trigger function, and the effects for A/D Input. After editing the settings, press the [STORE] button to store the settings. Settings made here are stored in the Live Set Sound. NOTE Simultaneously press the [ENTER] and [SETTINGS] buttons to instantly initialize the Live Set Sound (page 42). [EXIT] button While using the MENU and SETTINGS screens, press this button to exit from the current screen and return to the previous level. Holding down the [EXIT] button returns to the Top screen. Sliders Tone 16' 8 scale degrees below 5 1/3' 5 scale degrees above 8' Fundamental tone 4' 8 scale degrees above 2 2/3' 12 scale degrees above 2' 15 scale degrees above 1 3/5' 17 scale degrees above 1 1/3' 19 scale degrees above 1' 22 scale degrees above Panel controls CK88 CK61 Owner’s Manual 13 [MENU] button For calling up the screens for making overall settings (page 36). Simultaneously press the [ENTER] and [MENU] buttons to switch the panel lock on or off (page 42). [ENTER] button For confirming the parameter value or each operation. By holding down the [ENTER] button and operating other buttons or knobs, you can use shortcut operations (page 42). VALUE buttons Encoder dial For changing the currently selected parameter value. In the MENU and SETTINGS screens, use the encoder dial to move the cursor (or highlight) up and down. [SPLIT] button For selecting the Split settings. Pressing the button turns on the Split function, and each time you press the button, the settings change alternately in the order listed below. The lamp is on while the Split setting is selected, and the lamp is off while the Split setting is deselected, and the Layer setting is selected. The Split setting can be changed from the [SETTINGS] button  Sound  Common  Layer/Split  Mode (page 30). [SPLIT POINT] button For viewing the screen for changing the Split Point or the lowest note on the right section. Turn the Encoder dial or simply press the key you wish to assign as the Split Point. Settings made here are stored in the Live Set Sound. NOTE • The Split Point can be set by simultaneously pressing the [SPLIT POINT] button and the key you wish to assign as a Split Point. • The Split Point can be changed from the [SETTINGS] button  Sound  Common  Layer/Split  Split Point (page 30). CATEGORY buttons For selecting a Voice from the Voice Category to use for the Part. Every time you press the same button, the cursor moves to the next Voice in the same Category. Quickly pressing the button twice displays the Voice list. The Organ voices using the Organ Flutes tone generator (H, V, F, A, and Y) are available from the [Organ] button. These voices can be set using the ORGAN FOOTAGE sliders, PERCUSSION buttons, and VIBRATO/CHORUS buttons. Settings Descriptions A/BC Part A on the left section and Part B and C on the right section of the keyboard AB/C Part A and B on the left section and Part C on the right section of the keyboard A/B/C Part A on the left section, Part B on the center section, and Part C on the right section of the keyboard ABC Voices on Part A, B, and C are layered Types Descriptions H A distinctive electric organ from the 1960s, characterized by sine-like waveforms that are simple yet warm. This type of organ was used in many genres of music, such as rock, pop, and jazz. V A transistor organ from the 1960s. With harmonic content very close to that of a square wave, it had a sound of great presence. This type of organ was often used in psychedelic rock and ska. F A transistor organ from the 1960s. This type of organ is notable for its thick sound with the sawtooth components boosted in volume. It was often used in 60s pop music and alternative pop of the 90s. A A transistor organ made in Japan during the 1970s. This type of organ was notable for a bright sound similar to that produced by the sawtooth waveforms of a synthesizer. Panel controls CK88 CK61 Owner’s Manual 14 MONO-TYPE buttons For setting the tone generation mode for the selected Part. Use the [MONO] button to switch between Mono and Poly . The Mono mode is for playing a single note at a time and the Poly mode is for playing chords. Use the MONO [TYPE] button to select the Mono mode type. This also features Portamento types commonly used for classic pitch slides in synth lead sounds. NOTE • The time and mode for Portamento can be changed from the [SETTINGS] button  Sound  Part  Mono/Portamento (page 28). • Simultaneously press the [ENTER] and MONO [TYPE] buttons to view the screen for the Portamento time setting (page 42). UNISON-TYPE buttons For setting Unison for the selected Part. Use the [UNISON] button to turn the Unison mode on or off, and the UNISON [TYPE] button to select a Unison type. When the Unison mode is on, the Part sounds are layered to make them sound richer and thicker. In this Unison function, the Part sounds including the Insertion Effects are layered. Change the Unison volume and Detune setting from the [SETTINGS] button  Sound  Part  Unison (page 28). NOTE Simultaneously press the [ENTER] and UNISON [TYPE] buttons to view the screen for the Unison Detune setting (page 42). [STORE] button For saving (storing) the edited Live Set Sound. When storing, the following settings are saved to the internal memory of the keyboard. Stored settings will be retained when the CK is turned off. • Voices on Part A–C • Organ voice settings (Rotary Speaker, Vibrato/ Chorus, and Percussion) • Filter • EG • Drive • Effect1 and Effect2 • Delay • Reverb • [SETTINGS] (including Split and Transpose) NOTE EQUALIZER settings are stored to a Live Set Sound if Live Set EQ is set to On (page 30). [INPUT] button For setting the volume and effects for the audio input from the A/D INPUT jack. Pressing this button shows the same screen as pressing the [SETTINGS] button  A/D Input . Y A Yamaha transistor organ released in 1972. With harmonic content very close to that of a square wave, it was characterized by significant presence in the high range and extreme sound clipping with increased distortion. Type Descriptions Normal Simple Mono mode without Portamento Fingered Portamento Mono mode with Portamento used only while playing legato Full-Time Portamento Mono mode with Portamento used even when lifting your fingers from the keyboard Types Descriptions Type Description Multi Layer Unison that layers the Part sound played on the keyboard Harmonics Unison that layers the Part sound played on the keyboard at one octave higher Sub Harmonics Unison that layers the Part sound played on the keyboard at one octave lower Panel controls CK88 CK61 Owner’s Manual 15 PAGE buttons For switching the Live Set Page. The Live Set Sound changes accordingly. Simultaneously press the [ ] and [ ] buttons to call up the Live Set View. In the Live Set View, you can use the VALUE buttons and the Encoder Dial to select a Live Set Sound from a different Live Set Page. To go back to the Top screen, press the [EXIT] button. LIVE SET [1]–[8] buttons For calling up a Live Set Sound from the eight of the Live Set Sounds in the currently selected Live Set Page. Change the Live Set Page using the PAGE button. FILTER [ON/OFF] button FILTER [CUTOFF] knob FILTER [RESONANCE] knob For applying a filter to the currently selected Part. By setting the [ON/OFF] button to off , the filter is instantly reset to the initial value for the Voice. [CUTOFF] knob For setting the cutoff frequency of the low-pass filter. The sound can be brightened by moving the knob to the right or darkened by moving it to the left. NOTE How the filter is applied varies depending on the Voice being used. [RESONANCE] knob For setting the resonance, which changes the character of the sound. This effect can be made more pronounced by moving the knob to the right and less pronounced by moving it to the left. EG [ON/OFF] button EG [ATTACK] knob EG [RELEASE] knob For applying an EG (Envelope Generator) to the currently selected Part. By setting the [ON/OFF] button to off , the EG is instantly reset to the initial value for the Voice. [ATTACK] knob For adjusting the attack for the EG. Turn the knob to the left to make the attack faster, and to the right to make the attack slower. [RELEASE] knob For adjusting the release for the EG. Turn the knob to the left to make the release faster, and to the right to make the release slower. NOTE How the EG is applied varies depending on the Voice being used. Volume Cutoff Frequency Frequency (pitch) Cutoff range These frequencies are “passed” by the filter Volume Frequency (pitch) Resonance Level Key on Key off Time Attack Release Panel controls CK88 CK61 Owner’s Manual 16 DRIVE [ON/OFF] button DRIVE [DEPTH] knob Drive type select buttons For setting Drive, which applies on overdrive effect to the currently selected Part. Use the [ON/OFF] button to turn Drive on or off, and use the [DEPTH] knob to adjust values. Use the Drive Type select buttons to select a type. EFFECT 1 [ON/OFF] button EFFECT 2 [ON/OFF] button EFFECT [DEPTH] knob EFFECT [RATE] knob EFFECT [TYPE] knob EFFECT1–EFFECT2 select button For applying Insertion Effects to the currently selected Part. The Insertion Effects are applied in a path to Effect 1 and then to Effect 2. Use the [ON/OFF] button to turn the Effect on or off, and use the EFFECT1–EFFECT2 select button to select EFFECT1 or EFFECT2. The [TYPE] knob is used to select a type, the [DEPTH] knob to adjust the Insertion Effect depth, and the [RATE] knob to adjust the Insertion Effect rate. NOTE Simultaneously press the [ENTER] and EFFECT1–EFFECT2 select buttons to swap the EFFECT 1 and EFFECT 2 settings. This conveniently lets you change the order of the applied effects (page 42). There are various types of Insertion Effects with different characteristics. There are 10 effect type categories available. The category lamp for the selected effect type lights up. For more information on the effect types, see the “Effect list” on page 43. NOTE By holding down the [ENTER] button and operating the EFFECT [TYPE] knob, you can select the first item of the previous or the next category. This is convenient for quickly finding the category you wish to use (page 42). Type Description O.Drive Warm distortion effect (overdrive) Dist Hard rock distortion Rotary A Standard rotary speaker for organ. Rotary B The rotary speaker connected to a transistor preamplifier with strong distortion. Comp Versatile compressor controlled by a single knob Category Description Chorus Adds spaciousness and thickness to the sound, as if multiple sounds are played at once. Flanger Creates metallic sweeping sounds like a jet plane. Phaser Creates a phase-shifting effect that uses feedback circuitry as well as phase shift circuitry that mixes the phase-shifted sound with the original sound. Trm/Rtr Trm (Tremolo) is an effect that cyclically modulates the volume. Rtr (Rotary Speaker) is an effect that simulates a rotary speaker, which is popular for Organ sounds. Dist An effect that distorts sounds. Comp/EQ Comp (compressor) is an effect that compresses loud sounds or boosts soft sounds to even out the dynamics of the audio signal. EQ is an effect that changes the tonal character of the sound. Wah Creates a characteristic “wah-wah” sound by changing the frequency response of the filter. Delay Creates echo effects by delaying the time of the input sound. Reverb Creates a sense of space and ambience by artificially producing complex echoes. Others Other types of effects that are not included in the above categories. Panel controls CK88 CK61 Owner’s Manual 17 DELAY [ON/OFF] button DELAY [TYPE] button DELAY [DEPTH] knob DELAY [TIME] knob Use the [ON/OFF] button to turn the Delay on or off. Use the [TYPE] button to select a type, the [DEPTH] knob to set the delay depth, and the [TIME] knob to adjust the delay length. REVERB [ON/OFF] button REVERB [TYPE] button REVERB DEPTH knob Use the [ON/OFF] button to turn the Reverb on or off. Use the [TYPE] button to select a type and the REVERB DEPTH knob to adjust the reverb depth. EQUALIZER slider For adjusting the Master EQ. The lamp turns on when the slider value is set to a value other than 0. Set the Frequency for each type from the [MENU] button  General  System  Master EQ (page 36). EQUALIZER settings are stored to a Live Set Sound if Live Set EQ is set to On (page 30). The Live Set EQ setting is changed from the [SETTINGS] button  Sound  Common  Live Set EQ (page 30). Type Description Digital Delay Clean digital delay Use the [DEPTH] knob to adjust the depth and feedback level, and the [TIME] knob to adjust the delay time. Analog Delay Delay with warm analog sound Use the [DEPTH] knob to adjust the feedback level and the [TIME] knob to adjust the delay time. Cross Delay Delay that crosses the delay sound from left to right and from right to left Use the [DEPTH] knob to adjust the depth and feedback level, and the [TIME] knob to adjust the speed. Tempo Delay A special delay that syncs to the tempo of the song. The delay is applied by specifying the Tempo ( Tempo Delay Time ) and the note length. The initial value is 1/4 (quarter note). Use the [DEPTH] knob to change the delay depth and feedback level, and the [TIME] knob to adjust the delay tempo. Another intuitive way of setting the tempo is to tap the [ENTER] button at least three times. Tempo Delay Time can be set by using the [TIME] knob while holding down the [ENTER] button (page 42), or from the [SETTINGS] button  Sound  Common  Tempo Delay Time . Type Description Hall Reverb Simulates the sound of a concert hall. Room Reverb Simulates the sound of a room. Plate Reverb Simulates the sound of a plate reverb. Type Description [HIGH] Gain for the high-frequency band (500 Hz–16 kHz) [MID] Gain for the mid-frequency band (100 Hz–10 kHz) [LOW] Gain for the low-frequency band (32 Hz–2 kHz) Panel controls CK88 CK61 Owner’s Manual 18 Rear panel [DC IN] jack (page 20) For connecting the included AC adaptor. [ ] (STANDBY/ON) switch (page 22) For switching the CK to standby ( ) or turning it on ( ). OUTPUT jacks Standard phone (unbalanced) jacks for outputting audio signals. For output in mono, connect only to the [L/MONO] jack. A/D INPUT jacks Standard phone jacks (1/4" mono phone plug) for receiving audio from the external audio device. Musical instruments such as synthesizers, audio devices, such as portable music players, as well as dynamic microphones can be connected to these jacks, and the audio input signals can be played as an audio Part. In addition, the effects can be applied to external audio signals. The effect type can be set from the [INPUT] button. To switch the input source (to Line or MIC ), use the [MENU] button  General  Audio  A/D Input Type . NOTE The CK does not support phantom-powered condenser microphones. A/D INPUT [GAIN] knob The external audio source input via these jacks is mixed in with the sounds played by the CK. Use this knob to adjust the balance between the external audio and the CK sounds. FOOT PEDAL jacks For connecting a separately sold sustain pedal. The compatible pedals are Foot Pedal FC3A, Footswitch FC4A, Footswitch FC5, and Foot Controller FC7. Set the pedal type from the [MENU] button  General  Foot Pedal . NOTE When the pedal connected to the jack and the Foot Pedal setting do not match, the pedal may not work properly or may malfunction. Make sure to select the correct pedal type for the pedal connected to the jack. You can assign functions such as sustain or sostenuto from the [SETTINGS] button  Controllers  Foot Pedal 1 or Foot Pedal 2  Assign (page 31). SPEAKERS switch For tuning the built-in speakers on or off. If this switch is on and the Speaker Mute is set to Auto , the built-in speakers will automatically be muted when the headphones are connected. To change the Speaker Mute setting, set from the [MENU] button  General  System  Speaker  Speaker Mute . AC adaptor Keyboard amplifier or Monitor speakers External synthesizer Dynamic mic FC3A, FC4A AC outlet FC7 FC5 Panel controls CK88 CK61 Owner’s Manual 19 MIDI terminals With a standard MIDI cable (commercially available), you can connect an external MIDI instrument, and control it from the CK. Likewise, you can use an external MIDI device (such as a keyboard or sequencer) to control the internal tone generator on the CK. USB [TO DEVICE] terminal For connecting a USB flash drive to the CK, allowing you to save a Live Set Sound you have stored, load a Live Set Sound back to the CK, or play audio files. NOTE • Only a USB flash drive can be connected to the USB [TO DEVICE] jack. No other USB devices such as a hard disk drive, CD-ROM drive, or USB hub can be used. • You cannot record your performance onto a USB flash drive. USB [TO HOST] terminal For connecting the CK to a computer, iPhone, or iPad via a USB cable for using the MIDI and audio capability. With the USB [TO HOST] terminal, two MIDI ports (page 48) can be used simultaneously. NOTE The USB [TO HOST| terminal has the capacity for handing two mono channels (or one stereo channel) of 24-bit audio at a sampling rate of 44.1 kHz. [PHONES] jack For connecting a 6.3-mm standard stereo phone jack to connect headphones. When the Speaker Mute is set to Auto , the built-in speakers will be muted when the headphones are connected. CAUTION • To prevent hearing loss, avoid using headphones at high volumes for extended periods of time. • Whenever connecting external audio devices, ensure that all devices are turned off. NOTE The sound output via the headphones is identical to that output via the OUTPUT jacks. The sound is output via OUTPUT jacks regardless of whether or not the headphones are connected. The [PHONES] jack on the CK88 can be found on the front side. For CK88 USB flash drive MIDI device Computer Headphones Headphones CK88 CK61 Owner’s Manual 20 Although the CK will run either from an AC adaptor or batteries, Yamaha recommends the use of an AC adaptor whenever possible. An AC adaptor is more environmentally friendly than batteries and does not deplete resources. NOTICE It is recommended to use the AC adaptor when executing USB flash drive operations, since battery power may not be reliable enough to last through these crucial operations. Using an AC adaptor Make sure that the [ ] (Standby/On) switch is in a standby position (the switch is up), then connect the AC adaptor in the order shown in the illustration. 1. Wrap the DC output cable of the AC adaptor around the cord hook (as shown below), and then connect the plug of the adaptor to the DC IN jack on the rear panel. NOTICE Use of the cord hook prevents accidental unplugging of the cable during operation. Make sure to avoid tightening the cord more than necessary or pulling on the cord strongly while it is wrapped around the cord hook, in order to prevent wear on the cord or possible breakage of the hook. 2. Connect the other end of the AC adaptor to an AC outlet. WARNING • Use the specified AC adaptor (page 69) only. Using the wrong AC adaptor can result in damage to the instrument or overheating. • When using the AC adaptor with a removable plug, make sure to keep the plug attached to the AC adaptor. Using the plug alone can cause electric shock or fire. • If the plug is accidentally removed from the AC adaptor, never touch the metallic section when attaching the plug. To avoid electric shock, short circuit, or damage, also be careful that there is no dust between the AC adaptor and plug. CAUTION When setting up the product, make sure that the AC outlet you are using is easily accessible. If some trouble or malfunction occurs, immediately turn the power off and disconnect the plug from the outlet. NOTE • Follow the order shown above in reverse when disconnecting the AC adaptor. • When the AC adaptor is connected, the adaptor is used for supplying power to the instrument regardless of whether or not the batteries are installed to the instrument. • Do not insert or remove the DC plug with the [ ] (Standby/On) switch set to the On position ( ). Failure to observe this precaution can lead to malfunction. Setting up Cord hook AC outlet AC adaptor DC IN jack (page 69) Plug Slide the plug as indicated. The shape of the plug differs depending on your area. Setting up CK88 CK61 Owner’s Manual 21 Using batteries The CK requires eight “AA” size, Alkaline (LR6) or rechargeable nickel-metal hydride batteries (rechargeable Ni-MH batteries). Use of the AC adaptor is recommended when keeping the CK on for an extended time. 1. Make sure that the CK is turned off. 2. Turn the CK over and place the top side on a soft cloth. 3. Open the battery compartment cover. 4. Insert the eight new batteries, being careful to follow the polarity markings on the inside (or next to) the compartment. CK61 CK88 5. Close the compartment cover until it clicks into place. 6. Turn the CK face up. Do not leave the CK with the front panel side down. NOTICE • Connecting or disconnecting the AC adaptor with batteries installed may turn the power off, resulting in loss of data being edited at the time. • When battery power becomes too low for proper operation, the volume may be reduced, the sound may be distorted, and other problems may occur. When this happens, make sure to replace all batteries with new ones or already recharged ones. NOTE • This instrument cannot be used to charge the batteries. Use only the specified charger device when charging. • Power will be automatically drawn from the AC adaptor if an AC adaptor is connected while batteries are installed in the instrument. The bottom of the CK Battery compartment cover CK61 Battery compartment cover CK88 Setting up CK88 CK61 Owner’s Manual 22  Remaining battery power indication Turning the power on Turning the power off Make sure the volume settings of the CK and external devices such as powered speakers are turned down to the minimum before turning the power on. When connecting the CK to monitor speakers, turn on the power switch on each device in the following order.  Turning on Turn the [MASTER VOLUME] slider of the CK to its minimum  set the [ ] (STANDBY/ON) switch to on ( ).  turn the amplifier or speaker power on.  Turning off Turn the [MASTER VOLUME] slider of the CK to its minimum  turn the amplifier or speaker power off  set the [ ] (STANDBY/ON) switch to standby ( ). Setting the Auto Power Off function The Auto Power Off function automatically turns off the CK after 15 minutes of inactivity. As a factory default, Auto Power Off is set to Auto . With the Auto setting, the Auto Power Off function is disabled while the AC adaptor is being used, and enabled while the batteries are being used. NOTICE • The setting will revert to its default value if not backed up before the power is turned off. Make sure to store the settings before the Auto Power Off function becomes activated (page 24). • When the instrument is not operated for a specified period of time while connected to an external device such as an amplifier, speaker, or computer, make sure to follow the instructions in the Owner’s Manual to turn off the power to the instrument and the connected devices in the proper sequence, in order to protect the devices from damage. If you do not want the power to turn off automatically when a device is connected, disable Auto Power Off .  Auto Power Off setting Change the setting from the [MENU] button  General  System  Auto Power Off (page 36). Connecting headphones Connect a pair of headphones to the [PHONES] jack. When a set of headphones are connected while the Speaker Mute is set to Auto , the built-in speakers will be muted. When set to Manual , the built-in speakers will be muted by setting the SPEAKERS switch on the rear panel to OFF. The setting can be changed from the [MENU] button  General  System  Speaker . While the built-in speakers are muted, the output from the [PHONES] jack will also be output from OUTPUT jacks. CAUTION • Do not use the headphones for a long period of time at a high volume level, since this can cause permanent hearing loss. • Before connecting the instrument to other electronic components, turn off the power of all the components. Also, before turning any components on or off, make sure to set all volume levels to a minimum. Otherwise, damage to the components or electrical shock may occur. NOTICE To avoid possible damage to the external device, first turn on the power to the instrument, and then to the external device. When turning off the power, do so in reverse order: first turn off the power to the external device, and then to the instrument. Indication Description Indicates that the remaining power is sufficient. Indicates that the remaining power is insufficient for operation. The built-in speakers will be turned off after this indication is shown. Save the settings you are editing and replace all the batteries with new ones. Standard stereo phone plug Setting up CK88 CK61 Owner’s Manual 23 Using a USB flash drive By connecting a USB flash drive to the USB [TO DEVICE] terminal on the rear panel, you can save the Live Set Sounds as backup files or load settings back from the backup files. Precautions when using the USB [TO DEVICE] terminal When connecting a USB flash drive to the USB [TO DEVICE] terminal, be sure to follow the important precautions shown below. NOTE For more information on the handling of the USB flash drives, refer to the Owner’s Manual of your USB flash drive.  Compatible USB devices • USB flash drives only Other USB devices such as a USB hub, computer keyboard, or mouse cannot be used. The instrument does not necessarily support all commercially available USB devices. Yamaha cannot guarantee the operation of USB devices that you purchase. Before purchasing a USB device for use with this instrument, please visit the following web page: https://download.yamaha.com/ Although USB 1.1 and 2.0 devices can be used on the CK, the amount of time for saving to or loading from the USB flash drive may differ depending on the type of data or the status of the instrument. NOTICE The rating of the USB [TO DEVICE] terminal is a maximum of 5 V / 500 mA. Do not connect USB devices having a rating above this, since this can cause damage to the instrument itself.  Connecting a USB flash drive When connecting a USB flash drive to the USB [TO DEVICE] terminal, make sure that it is connected in the proper direction. NOTICE • Avoid connecting or disconnecting the USB device during file management operations (such as Save, Copy, Delete, and Format), or when accessing the USB flash drive. Failure to observe this may result in “freezing” of the operation of the instrument or corruption of the USB flash drive. • When connecting then disconnecting the USB flash drive (and vice versa), make sure to wait a few seconds between the two operations. • Do not use cables for connecting the USB flash drive.  Formatting the USB flash drive Some USB flash drives should be formatted with this instrument before they can be used (page 36). The USB flash drives formatted on other instruments or devices may not work properly. NOTICE The format operation erases any existing files. Make sure that the USB flash drive you are formatting does not contain any important files.  To protect your files (Write Protection) To prevent important files from being inadvertently erased, write-protect the USB flash drive. When you are saving files to the USB flash drive, make sure you disable the write-protection first.  Turning off the instrument When turning off the instrument, make sure that the instrument is NOT accessing the USB flash drive by file management (such as during Save, Copy, Delete and Format operations). Failure to do so may corrupt the USB flash drive and the files. CK88 CK61 Owner’s Manual 24 Top screen configuration This section explains the Top screen which appears when the CK is turned on. Live Set Sound number Shows the currently selected Live Set Sound number. With the initial setting, number 1-1 will be called up at startup. To use a different Live Set Sound number for startup, change the setting from the [MENU] button  General  System  Power on Sound (page 36). Voice Shows the Voice name when the Part is on. With some Organ voices, the Voice name and the Drawbar settings will be shown. Split and Layer Shows the current split and layer status of each Part. The split point is the lowest key on the right keyboard range. Other icons Creating a Live Set Sound Use the Live Set Sound for sound-making. The basic sound-making procedures are as shown below. 1. Select a Live Set Sound. 2. Select a Voice for each Part. 3. Set a combination of these Voices. 4. Creating an Organ voice. 5. Modify sounds using EG, Filter, Effects, MONO, and Unison settings. 6. Save the Live Set Sound. Saving the Live Set Sound Edited Live Set Sounds are saved to the internal memory of the CK by pressing the [STORE] button. 1. Press the [STORE] button. A screen for selecting the Live Set Sound to be stored appears. Basic operations Panel lock is on. The setting can be changed by simultaneously pressing both the [ENTER] and [MENU] buttons. Sound Transpose for the Live Set Sound is set to a value other than 0 (−12 to +12). Live Set EQ is set to on. Audio Trigger is set to ON. Master Keyboard is set to ON. Connected via Bluetooth. Battery level (shown only during battery operation). (For Part A) Touch Sensitivity for the Part has been changed. External Keyboard for the Part is set to ExtOnly Play the external keyboard to sound the internal tone generator. Note Shift for the Part is set to a value other than 0 (±24) When the note value is −24, −12, +12, and +24, it is shown as OCT−2, OCT−1, OCT+1, and OCT+2 Select a voice and combine voices Adjust the organ sound Apply sound effects Select a Live Set Sound CK88 CK61 Owner’s Manual 25 2. Use the Encoder dial to select the desired Live Set Sound number for saving to. You can audition the Voice already saved to the Live Set Sound number by playing the keyboard before saving the new one. NOTICE • The settings will be overwritten if you select the same number as an existing Live Set Sound. • The settings currently editing will be lost if you select a different Live Set Sound or turn off the power before storing the settings. 3. Press the [ENTER] button to store. When the store operation is complete, the message “ Completed ” will appear and operation returns to the Top screen. If a different Live Set Sound Number was selected when saving the currently editing Live Set Sound, the Live Set Sound before the edit will be kept unchanged in the original Live Set Sound Number. NOTE If you have accidentally changed to a different Live Set Sound causing your edits to be lost, you can use the Edit Recall function to recall the last edited status (page 40). These powerful and convenient features for Live Set Sound let you apply effects to the audio input via A/D input or play back an audio file while performing on the keyboard. Applying effects to audio signals from the A/D INPUT jacks You can connect another electronic musical instrument, guitar, or a microphone to the A/D INPUT jacks, and apply dedicated effects to those external audio sources. Here, we’ll cover how to use a dynamic microphone. 1. Connect a dynamic mic to the A/D Input [L/ MONO] jack on the rear panel. Example for a dynamic mic 2. Select Mic from the [MENU] button  General  Audio  A/D Input Type . 3. Press the [INPUT] button. The A/D Input screen appears. 4. Select an effect type from the Input Effect1 or Input Effect2 TYPE. This completes the setup. Press the [STORE] button to save the A/D Input settings to the Live Set Sound. Playing back an audio file While playing the Live Set Sound, you can play back an audio file saved on a USB flash drive using a single key on the keyboard. 1. Save the desired audio file (.wav) to the USB flash drive from a computer. The supported audio file is in .wav format (44.1 kHz, 16-bit, Stereo). Files of .wav format in 48-kHz or mono cannot be played back on the CK. 2. Insert the USB flash drive to the USB [TO DEVICE] terminal on the rear panel. 3. Select from the [SETTINGS] button  Function  Audio Trigger . 4. Change the settings. • Switch : Set to ON • File : Select the audio file to play back • Volume : Set the playback volume • Key Assign : Select the rightmost key or the leftmost key to start or stop playback. • Play Mode : Sets the mode for playback 5. Press the key specified in Key Assign to start playback at the desired timing. Playback then starts. Set the mode for playing back audio files from Play Mode . The Play Mode setting can be changed from the [SETTINGS] button  Function  Audio Trigger  Play Mode (page 32). Other Live Set Sound features CK88 CK61 Owner’s Manual 26 Editing Live Set Sound names Select the desired Live Set Sound for which you wish to edit the name  [SETTINGS] button  Name  Edit the name  [ENTER] button  Select Store . NOTE If “ Do not store now ” is selected, the Live Set Sound will not be stored, but the edited name will be retained.  Operations during name edit Use the Live Set Sound [1] and [2] buttons to move the cursor to the position of the character you wish to edit. Use the VALUE buttons and Encoder dial to select characters, and then use other buttons as listed below to edit the name. Swapping or copying Live Set Sounds 1. Call up the Live Set Sound you want to swap from or copy from. 2. Use the [MENU] button  Job  Live Set Manager  Swap or Copy . 3. Use the Encoder dial to select the desired Live Set Sound to swap to or to copy to. 4. Press the [ENTER] button. When the operation is completed, the message “ Completed ” appears on the screen, and then operation returns to the Top screen. Initializing a Live Set Sound When initializing a Live Set Sound, only Part A is enabled (set to ON), and the first Voice in the Piano category will be selected. All settings for Filters, EG, and effects will be reset to their initial values. 1. Call up the Live Set Sound you want to initialize. 2. Select from the [MENU] button  Job  Live Set Manager  Initialize . 3. Use the Encoder dial to select Live Set Sound Init . 4. Press the [ENTER] button. When initialization is complete, the message “ Completed ” appears on the screen, and then operation returns to the Top screen. NOTE If you want to reset the Live Set Sound to the default settings, simultaneously press the [EXIT] and [SETTINGS] buttons (page 42). This operation does not overwrite the stored Live Set Sound. Managing Live Set Sounds Buttons Functions LIVE SET [1] Moves the cursor to left. LIVE SET [2] Moves the cursor to right. LIVE SET [3] Inserts a highlighted character at the cursor position. LIVE SET [4] Deletes the character at the cursor position. LIVE SET [5] Changes the highlighted character at the cursor position to the desired one. LIVE SET [7] Reverts all characters to the unedited name. LIVE SET [8] Deletes all characters. [ENTER] Saves the name and ends editing. [EXIT] Ends editing without saving the name. Cursor Character selected for entry Managing Live Set Sounds CK88 CK61 Owner’s Manual 27 Saving the Live Set Sound to a USB flash drive The Live Set Sound stored in the internal memory of the CK can be saved to a USB flash drive as a backup file. Before using a USB flash drive, be sure to read “Precautions when using the USB [TO DEVICE] terminal” (page 23). 1. Connect a USB flash drive to the USB [TO DEVICE] terminal of the CK. 2. Select the [MENU] button  File . 3. Select the type of file you wish to save. 4. Select Save and press the [ENTER] button to call up the screen for selecting the destination.  When saving as a new file Select New File .  When overwriting an existing file Select the desired file from the displayed list. 5. Press the [ENTER] button. The Save *** File screen for editing file name appears. For details on name editing operations, see “Operations during name edit” (page 26). 6. Press the [ENTER] button to save. When the save operation is complete, a “ Completed ” message appears in the display, and then operation returns to the Top screen. Changing a previously saved file name [MENU] button  File  File Utility  Rename  Select the desired file for which you wish to edit the name  Edit the name  [ENTER] button to save the file. Loading a Live Set Sound from a USB flash drive For file types other than a Live Set Sound File , you can select and load a single desired Live Set Sound included in the file. To do this, select Load Live Set Sound in step 6 to call up the screen for selecting a specific Live Set Sound in the file. Then select the desired Live Set Sound to load. The setting is loaded into the currently selected Live Set Sound number. NOTICE The Load operation overwrites the Live Set Sounds stored in the CK. Important settings should always be saved to a USB flash drive. 1. Connect a USB flash drive to the USB [TO DEVICE] terminal of the CK. 2. Select the [MENU] button  File . 3. Select the type of file you wish to load from the USB flash drive. 4. Select Load and press the [ENTER] button. 5. Select the file in the USB flash drive. To cancel the load operation, select Cancel and press the [ENTER] button. 6. Select Load All or Load to *** and then press the [ENTER] button. When the load operation is complete a “ Completed ” message appears in the display, and then operation returns to the Top screen. File type Description Back Up File All Live Set Sounds including the settings for the entire instrument. Live Set All File All Live Set Pages. Live Set Page File Currently selected Live Set Page. Live Set Sound File Currently selected Live Set Sound. File type Description Back Up File (Extension .Y1A) All Live Set Sounds including the settings for the entire instrument. Live Set All File (Extension .Y1L) All Live Set Pages. Live Set Page File (Extension .Y1P) One Live Set Page. The file will be loaded to the currently selected Live Set Page. Live Set Sound File (Extension .Y1S) One Live Set Sound. The file will be loaded to the currently selected Live Set Sound. CK88 CK61 Owner’s Manual 28 Live Set (SETTINGS button) From the [SETTINGS] button, you can configure and store the various settings of the currently selected Live Set Sound. After editing, make sure to save the settings by pressing the [STORE] button. The changes made here will be stored to the Live Set Sound. Operation 1. Press the [SETTINGS] button. 2. Use the VALUE buttons and Encoder dial to select an item, and then press the [ENTER] button. NOTE You can also use the LIVE SET buttons [1] to [6] to select the item. The LIVE SET buttons [1] to [6] correspond to the items shown on the display in order from the top. The buttons light up when this feature is available. 3. Use the VALUE buttons or Encoder dial to change the value, and then press the [ENTER] button. When the setting has been changed, the operation goes back to the previous screen for selecting the settings item. Sound Advanced settings Function name Description Part A Part B Part C Mono/ Portamento Mono/Poly Selects whether to play the Part as monophonic ( Mono ) or polyphonic ( Poly ). Default: Poly Type Determines how the portamento effect is used depending on how you play the keys. • Normal : The normal mono sound is played. Portamento is not used. • Fingered : Portamento is used only when you play legato (playing a key while still holding the previous key). • Full-time : Portamento is always used. Default: Normal Portamento Time Determines the speed or time that takes for the portamento pitch change. Settings: 0–127 Portamento Time Mode Determines the time standard for portamento pitch change. • Rate : The pitch changes at the specified speed. • Time : The pitch changes over the specified time. Default: Rate Unison Switch Enables or disables the Unison function. Type Selects a Unison type. • Multi Layer : The Part sound played on the keyboard is layered • Harmonics : The Part sound played on the keyboard is layered at one octave higher • Sub Harmonics : The Part sound played on the keyboard is layered at one octave lower Default: Multi Layer Volume Adjusts the Part volume layered with the Unison function. Settings: 0–127 Detune Sets the amount of detuning between the Parts layered with the Unison function. By layering the detuned sounds, you can achieve a chorus-like effect. Settings: 0–127 Advanced settings CK88 CK61 Owner’s Manual 29 Part A Part B Part C Note Shift Shifts the keyboard pitch in semitones. Settings: −24–+0–+24 Default: +0 NOTE The value is not transmitted as a MIDI message. Modulation P.Mod Depth Pitch Modulation cyclically changes the pitch. P.Mod Depth determines the pitch modulation depth. Settings: 0–127 F.Mod Depth Filter Modulation cyclically changes the cutoff frequency. F.Mod Depth determines the filter modulation depth. Settings: 0–127 A.Mod Depth Amplitude Modulation cyclically changes the volume. A.Mod Depth determines the amplitude modulation depth. Settings: 0–127 Modulation Speed Determines the modulation speed. This setting is applied commonly to P.Mod , F.Mod , and A.Mod . Settings: −64–+0–+63 Touch Sensitivity Depth Determines the degree to which the resulting volume of the tone generator responds to your playing strength. The higher the value, the more the volume changes in response to your playing strength (as shown below). Settings: 0–127 Function name Description 127 0 127 When Offset (below) is set to 64 Actual resulting velocity (affecting the tone generator) Velocity with which you play a note Depth = 127 Depth = 64 Depth = 32 Depth = 0 Advanced settings CK88 CK61 Owner’s Manual 30 Part A Part B Part C Touch Sensitivity Offset Determines the amount by which played velocities are adjusted for the actual resulting velocity effect. This lets you raise or lower all velocities based on this setting value—allowing you to automatically compensate for playing too strongly or too softly. However, because of automatic compensation, the value will be set to 1 when the result is smaller than 1, and the value will be set to 127 when the result is larger than 127. Settings: 0–127 Common Transpose Changes the pitch up or down in semitones. Settings: −12–+12 Default: +0 NOTE This setting does not affect MIDI output messages. Layer/Split Mode Selects the combination of Layer and Split. You can also use the [SPLIT] button for this setting. Settings: ABC , A/BC , AB/C , A/B/C Default: ABC Split Point Sets the Split Point or the lowest note on the right keyboard range using a note name. When using the split mode A/B/C , two Split Points are needed. You can also use the [SPLIT] button to set the split point. Settings: C # -2–G8 Default: G2 C3 is MIDI note number 60. Live Set EQ Mode SW Turns the Live Set EQ Mode on / off . Default: Off EQ Settings Sets the EQ for the Live Set Sound. High Gain Sets the gain for the high band. Settings: −12 dB–0–+12 dB High Frequency Sets the frequency for the high band. Settings: 500 Hz–16 kHz Function name Description 127 0 127 64 127 64 127 0 127 64 127 0 When Depth = 64 and Offset = 32 Actual resulting velocity (affecting the tone generator) Velocity with which you play a note Actual resulting velocity (affecting the tone generator) Velocity with which you play a note Actual resulting velocity (affecting the tone generator) Velocity with which you play a note When Depth = 64 and Offset = 64 When Depth = 64 and Offset = 96 Advanced settings CK88 CK61 Owner’s Manual 31 Controllers Common Live Set EQ EQ Settings Mid Gain Sets the gain for the mid-band. Settings: −12 dB–0–+12 dB Mid Frequency Sets the frequency for the mid-band. Settings: 100 Hz–10 kHz Low Gain Sets the gain for the low band. Settings: −12 dB–0–+12 dB Low Frequency Sets the frequency for the low band. Settings: 32 Hz–2.0 kHz Tempo Delay Time When Tempo Delay is selected for Delay , this sets the delay time in note lengths to match the tempo. Settings: 1/32 Tri.–1/2 Default: 1/4 NOTE The tempo should be set with the [TIME] knob or with Tap Tempo using the [ENTER] button. Function name Description Pitch Bend Range Part A Determines the pitch bend range in semitones. Settings: −24–+0–+24 Default: +2 Part B Part C Mod Wheel Assign Determines the function to be assigned to the Modulation wheel. You can assign the Modulation wheel to Control Change numbers 1 to 119 or the USB Audio volume . Settings: Off , 1–119, USB Audio Volume Default: 1 (Modulation) Foot Pedal 1 Foot Pedal 2 Assign Determines the Control Change number to be assigned to a pedal connected to the FOOT PEDAL jack. You can assign each Foot Pedal to Control Change numbers 1 to 119, or to control the USB Audio volume . Settings: Off , 1–119, USB Audio Volume Default: Foot Pedal 1: 64 (Sustain) Foot Pedal 2: 11 (Expression) Limit Low Determines the lowest value for the foot controller (FC7) connected to the FOOT PEDAL jack. Settings: 0–127 Default: 0 Limit High Determines the highest value for the foot controller (FC7) connected to the FOOT PEDAL jack. Settings: 0–127 Default: 127 Receive SW Expression Part A Part B Part C Determines whether each Part receives ( On ) or ignores ( Off ) the corresponding MIDI messages received from external devices or the messages generated by operating the footswitch or foot controller. Default: On Sustain Sostenuto Soft Function name Description Advanced settings CK88 CK61 Owner’s Manual 32 Function Function name Description Part Color Part A Sets the LED color for the Part. Settings: Red , Orange , Yellow , Lime , Green , Spring , Cyan , Azure , Blue , Violet , Magenta , Rose Part B Part C Audio Trigger Switch Switches the Audio Trigger function. Default: Off File Selects the audio file to use with the Audio Trigger function. Volume Sets the playback volume for the audio file. Settings: 0–127 Key Assign Selects the key for starting playback of the audio file. Settings: Lowest , Highest Default: Highest Play Mode Sets the playback mode for the audio file. • One Shot : Plays back the audio file from the beginning every time the key is pressed. • Play/Stop : Starts or stops the playback of the audio file each time the key is pressed. The playback starts from the beginning of the file. • Play/Pause : Starts or pauses the playback of the audio file each time the key is pressed. The playback resumes from the paused place. Default: One Shot External Keyboard Determines how the Parts are played when the CK receives performance information (key-on, key-off ) MIDI messages from an external MIDI device. You can set up the CK with an external keyboard like a two-manual organ, or set up only a specific Part to play from the external keyboard. NOTE For Parts that are played only from an external keyboard, the Split setting shown on the Top screen changes from to . Part A Part B Part C • Ext+Int : Internal tone generator plays sounds with both key-on signals received from an external MIDI device and performance on the CK’s keyboard. • ExtOnly : Internal tone generator plays sounds only for key-on signals received from an external MIDI device. No sound is played when the keyboard on the CK is played. • Off : Internal tone generator does not play sounds for key-on signals received from an external MIDI device. Sound is played only when the keyboard on the CK is played. Default: Ext+Int Connection example (for setting up the piano for Part A on the CK61 to be played only on the MX88) Part A = ExtOnly , Part B = Off , Part C = Off CK61 MX88 MIDI [IN] terminal MIDI [OUT] terminal Advanced settings CK88 CK61 Owner’s Manual 33 Master Keyboard This function is for using the CK as a master keyboard. It allows you to assign different areas of the keyboard to up to four zones, each of which can control a separate tone generator. For example, you can make a Live Set Sound combining Voices from both the CK and the connected external tone generators, or a Live Set Sound composed entirely with Voices of external tone generators. Example for combining the internal tone generator and Zones 1 to 3 Mode SW Switches the Master Keyboard mode. When On is selected, the Master Keyboard mode is enabled, and the indication appears on the Top screen. Default: Off Advanced Zone SW Changes the settings shown for Master Keyboard mode. When On is selected, the items with an asterisk (*) will be shown on the display. Default: Off Zone Settings Zone1 Zone2 Zone3 Zone4 Zone Switch Determines whether to enable ( On ) or disable ( Off ) the zone. Default: Zone 1 = On , Zone 2–4 = Off Tx Channel Determines the MIDI transmit channel for the zone. Settings: 1–16 Default: Zone 1 = 1, Zone 2 = 2, Zone 3 = 3, Zone 4 = 4 Octave Shift Shifts the pitch of the zone in octaves. Settings: −3–+3 Default: +0 Transpose Changes the pitch of the zone in semitones. Settings: −11–+11 Default: +0 Note Limit Low Sets the lowest key in the zone. Default: C−2 Note Limit High Sets the highest key in the zone. Default: G8 Bank MSB * Determines the Bank Select MSB sent as a MIDI message to the external tone generator played by the zone. Default: 0 Bank LSB * Determines the Bank Select LSB sent as a MIDI message to the external tone generator played by the zone. Default: 0 Function name Description Internal tone generator External tone generator (Zone) Zone 1 Zone 2 Zone 3 Advanced settings CK88 CK61 Owner’s Manual 34 Master Keyboard Zone Settings Zone1 Zone2 Zone3 Zone4 Program Change * Determines the Program Change Number sent as a MIDI message to the external tone generator played by the zone. Default: 1 Volume * Determines the volume sent as a MIDI message to the external tone generator played by the zone. Default: 100 Pan * Determines the panning sent as a MIDI message to the external tone generator played by the zone. Default: C Tx SW Note * Determines whether to transmit ( On ) or not transmit ( Off ) MIDI note messages to the external tone generator played by the zone. Default: On Tx SW Bank * Determines whether to transmit ( On ) or not transmit ( Off ) MIDI Bank Select messages to the external tone generator played by the zone. Default: On Tx SW Program * Determines whether to transmit ( On ) or not transmit ( Off ) MIDI Program Change messages to the external tone generator played by the zone. Default: On Tx SW Volume * Determines whether to transmit ( On ) or not transmit ( Off ) MIDI volume messages to the external tone generator played by the zone. Default: On Tx SW Pan * Determines whether to transmit ( On ) or not transmit ( Off ) MIDI Pan messages to the external tone generator played by the zone. Default: On Tx SW PB * Determines whether to transmit ( On ) or not transmit ( Off ) MIDI Pitch Bend messages to the external tone generator played by the zone. Default: On Tx SW Mod * Determines whether to transmit ( On ) or not transmit ( Off ) MIDI Modulation messages to the external tone generator played by the zone. Default: On Tx SW Foot Pedal 1 * Determines whether to transmit ( On ) or not transmit ( Off ) MIDI messages for FOOT PEDAL [1] to the external tone generator played by the zone. Default: On Tx SW Foot Pedal 2 * Determines whether to transmit ( On ) or not transmit ( Off ) MIDI messages for FOOT PEDAL [2] to the external tone generator played by the zone. Default: On Function name Description Advanced settings CK88 CK61 Owner’s Manual 35 A/D Input Name Determines the name of a Live Set Sound. For details on editing Live Set Sound names, see Editing Live Set Sound names (page 26). To store the edited Live Set Sound names, you’ll need to use the Store operation (page 10). Function name Description Volume Adjusts the volume of the audio signal input from the A/D INPUT jack for the Live Set Sound. NOTE Adjust the overall volume with the A/D INPUT [GAIN] knob. Settings: 0–127 Input Effect 1 Input Effect 2 Type Selects the type of Effect applied to the audio. Settings: Thru , Effect type (see “Effect list” on page 43) Default: Thru Depth Adjusts the depth of the Effect applied to the audio. Settings: 0–127 Rate Adjusts the rate of Effect applied to the audio. Settings: 0–127 Input EQ Sets the 3-band EQ for the audio. High Gain Sets the signal level for the high band. Settings: −12 dB–0–+12 dB High Frequency Sets the frequency for the high band. Settings: 500 Hz–16 kHz Mid Gain Sets the signal level for the mid-band. Settings: −12dB–0–+12dB Mid Frequency Sets the frequency for the mid-band. Settings: 100 Hz–10 kHz Low Gain Sets the signal level for the low band. Settings: −12 dB–0–+12 dB Low Frequency Sets the frequency for the low band. Settings: 32 Hz–2.0 kHz Noise Gate Switch Turns the noise gate for the audio on/off. Settings: Off , On Default: Off Threshold Sets the threshold for the noise gate for the audio. Settings: −73 dB–−30 dB Default: −45 dB Advanced settings CK88 CK61 Owner’s Manual 36 Entire instrument (MENU button) From the [MENU] button, you can configure various parameters and functions that affect the entire instrument. The changes made here will be stored in the CK. NOTICE After the value has been changed, the setting will be saved when the operation goes back to the Top screen. Changes will not be saved if the CK has been turned off before the operation has gone back to the Top screen. Operation 1. Press the [MENU] button. 2. Use the VALUE buttons and Encoder dial to select an item, and then press the [ENTER] button. NOTE You can also use the LIVE SET buttons [1] to [6] to select the item. The LIVE SET buttons [1] to [6] correspond to the items shown on the display in order from the top. The buttons light up when this feature is available. 3. Use the VALUE buttons and Encoder dial to change the value, and then press the [ENTER] button. When the setting has been changed, the operation goes back to the previous screen for selecting the menu item. General Function name Description System Master Tune Determines the tuning for the entire instrument. Settings: 414.72 Hz–466.78 Hz Default: 440.00 Hz Master EQ Sets the Master EQ . High Frequency Sets the frequency for the high band. Settings: 500 Hz–16 kHz Mid Frequency Sets the frequency for the mid-band. Settings: 100 Hz–10 kHz Low Frequency Sets the frequency for the low band. Settings: 32 Hz–2.0 kHz Speaker Speaker EQ Selects the optimal sound quality of the built-in speakers for setting the CK on a keyboard stand where the bottom of the CK is open ( Normal ) or for setting on the table where the bottom of the CK is covered ( Table ). Settings: Normal , Table Default: Normal Speaker Mute Selects to mute the built-in speakers automatically ( Auto ) or to mute the built-in speakers manually using the SPEAKERS switch ( Manual ) when the headphones are connected. Settings: Auto , Manual Default: Auto Auto Power Off Switches the Auto Power Off function setting. • Disable : The CK is not automatically turned off. • Enable : The CK is turned off automatically after being inactive for 15 minutes. • Auto : The Auto Power Off function is disabled while the AC adaptor is being used, and enabled while batteries are being used. Default: Auto Power On Sound Selects which Live Set Sound is automatically called up when the CK is turned on. Default: 1-1 Advanced settings CK88 CK61 Owner’s Manual 37 MIDI MIDI Port MIDI Determines whether to use the MIDI terminals for transmitting or receiving MIDI messages with the internal tone generator. • On : Used as Port 1 (transmit or receive MIDI messages with the internal tone generator). • Off : Used as Port 2 (USB-MIDI interface). In this case, MIDI messages received by the MIDI [IN] terminal are sent to USB Port 2 (MIDI OUT 2). MIDI messages received by the USB Port 2 (MIDI IN 2) are sent to the MIDI [OUT] terminal. Default: On USB Determines whether to use ( On ) the USB [TO HOST] terminal for transmission/ reception of MIDI messages, or not ( Off ). Default: On MIDI Channel Transmit Determines the MIDI transmit channel. When this is set to Off , MIDI messages are not transmitted. Settings: 1–16, Off Default: 1 Receive Determines the MIDI receive channel. When this is set to All , MIDI messages will be received over all channels. Settings: 1–16, All Default: 1 MIDI Control Sets the MIDI control message to be sent out when using knobs and sliders on the front panel. For MIDI Control , the keyboard, Pitch Bend, Modulation, and pedals are excluded. • On : MIDI messages are transmitted when the corresponding controllers such as knobs and sliders are used, allowing you to use a DAW and external MIDI devices to receive and record the operation information. • Off : MIDI messages are not transmitted when the corresponding controllers are used. Default: Off NOTE • When MIDI messages corresponding to knobs and sliders are received from the DAW, the settings for those knobs and sliders are changed. • The MIDI message assignment for each knob or the slider is fixed. If you want to control the parameters in the DAW from the knobs and sliders on the CK, set up the computer to receive messages from the knobs and sliders. For details on MIDI messages, see page 54. Local Control Determines whether Local Control is on or off. When this is set to Off , the CK’s tone generator is disconnected from the keyboard, and no sound will be produced when the keyboard is played. However, regardless of the setting here, performance information from the CK’s keyboard is transmitted as MIDI messages, and the CK’s tone generator will continue to produce sound in response to the MIDI messages received from MIDI input, depending on the MIDI settings. Default: On Controller Reset Determines whether to keep ( Hold ) or initialize ( Reset ) the values of controllers (such as Modulation wheel and Foot Controller) when switching to a different Live Set Sound. When this is set to Reset , the controllers are reset to the default as shown below when switching to a different Live Set Sound. • Pitch Bend: Center • Modulation: Minimum • Expression: Maximum • Pedal Wah: Minimum Default: Reset Function name Description Advanced settings CK88 CK61 Owner’s Manual 38 MIDI Advanced Device Number Determines the MIDI device number. The device number of the CK must match the device number of the external MIDI device when transmitting or receiving Bulk Dump, Parameter Changes, or other System Exclusive messages. Settings: 1–16, All , Off Default: All Control Delay Adjusts the transmission timing for MIDI control messages transmitted when switching to a different Live Set Sound. Adjust the setting when the application on your computer does not receive messages correctly. Settings: 0–1500 msec Default: 0 msec Tx/Rx Pgm Change Determines whether transmission/reception of Program Change messages between the CK and external MIDI devices is enabled ( On ) or disabled ( Off ). Default: On Tx/Rx Bank Select Determines whether transmission/reception of Bank Select messages between the CK and external MIDI devices is enabled ( On ) or disabled ( Off ). Default: On Audio Output Gain Adjusts the overall final output level of the CK. Settings: −24 dB–+0 dB–+24 dB Default: +0 dB A/D Input Type Selects a line input ( Line ) or a dynamic mic ( Mic ) for use as the input source from the A/D INPUT jack. Default: Line USB Audio Volume Determines the volume of the USB Audio input. Settings: 0–127 Default: 64 USB Audio Loopback Determines whether to mix the USB Audio input to the USB Audio Output ( On ) or not ( Off ). Default: Off Control Panel Panel Lock Settings Live Set When the Panel Lock function is enabled, this allows you to set Panel Lock for specific functions/operations on or off. Default: On Organ Filter/EG Drive/Effect Delay/Reverb Equalizer Display Value Indication Determines whether to show ( On ) or not show ( Off ) the values on the display (LCD) when the values for the controllers of each Part are changed. Default: On LCD Switch Determines whether to show ( On ) or not show ( Off ) the Top screen on the display (LCD). The MENU and SETTINGS screens are always shown on the display regardless of the settings selected here. Default: On LCD Contrast Adjusts the contrast of the Display (LCD). Settings: -10–+10 Default: +0 Function name Description Advanced settings CK88 CK61 Owner’s Manual 39 Control Panel Controller Mode Sets the conditions for a controller position to be reflected when the controllers’ actual position and values called up with the LIVE SET [1] to [8] buttons do not match. • Jump : The position of a controller is reflected immediately when that controller is moved. • Catch : The current setting will be held until the controller’s position matches (catches) values called up with the LIVE SET [1] to [8] buttons. Once the values have matched, the controller’s position will be reflected. Default: Jump Filter/EG Reset Determines whether to reset ( On ) or maintain without resetting ( Off ) the EG and FILTER parameters when a Voice for the Part has been changed. Default: On Effect On/Off Reset Determines whether to reset ( On ) or maintain without resetting ( Off ) the Effect parameters when a Voice for the Part has been changed. Default: On Keyboard Touch Curve Determines how actual velocities will be generated according to the strength with which you play notes on the keyboard. • Normal : This linear “curve” produces one-to-one correspondence between the strength of your keyboard playing (velocity) and the actual sound change. • Soft : This curve provides an increased response, especially for lower velocities. • Hard : This curve provides an overall decreased response, especially for higher velocities, meaning that greater strength is needed to produce louder sound. • Wide : This curve accentuates your playing strength by producing lower velocities in response to softer playing and louder velocities in response to harder playing. As such, you can use this setting to expand your dynamic range. • Fixed : This setting produces the same amount of sound change, no matter what your playing strength. The velocity of the notes you play is fixed at the value set here. Default: Normal Fixed Velocity When Touch Curve above is set to Fixed , this lets you set the desired fixed velocity, letting you keep the same, regardless of how hard or soft you play the keyboard. Settings: 1–127 Default: 64 Foot Pedal Pedal 1 Pedal 2 Pedal Type Sets the type of pedal connected to the FOOT PEDAL [1] jack or the FOOT PEDAL [2] jack. Select FC3A (HalfOn) when using a Half Damper pedal. Settings: FC3A (HalfOn) , FC3A (HalfOff) , FC4A/FC5 , FC7 Default: Pedal 1 : FC3A (HalfOn) Pedal 2 : FC7 Live Set Inc/Dec Sets the type of operation for using the pedals connected to the FOOT PEDAL [1] jack or the FOOT PEDAL [2] jack. • Off : Operates the control change assigned to the Live Set Sound. • Live Set Inc : Selects the next Live Set Sound when operating the pedal. • Live Set Dec : Select the previous Live Set Sound when operating the pedal. Default: Off Function name Description Advanced settings CK88 CK61 Owner’s Manual 40 Job Function name Description Live Set Manager Swap Swaps the currently selected Live Set Sound with another user-specified Live Set Sound. Copy Copies the currently selected Live Set Sound to another user-specified Live Set Sound. Initialize Resets all parameters of the currently selected Live Set Sound to their defaults. Part/Effect Manager Copy Part A Copies the Part A settings of the Live Set Sound. Part B Copies the Part B settings of the Live Set Sound. Part C Copies the Part C settings of the Live Set Sound. Delay Copies the Delay settings of the Live Set Sound. Reverb Copies the Reverb settings of the Live Set Sound. Paste Part A Pastes the copied settings. The paste function cannot be used when nothing has been copied. Part B Part C Delay Reverb Swap Part Part A  B Swaps the Part A settings and the Part B settings of the Live Set Sound. Part B  C Swaps the Part B settings and the Part C settings of the Live Set Sound. Part C  A Swaps the Part C settings and the Part A settings of the Live Set Sound. Swap EFFECT 1/2 Part A Swaps the EFFECT 1 settings and the EFFECT 2 settings of a specified Part in the Live Set Sound. Part B Part C Edit Recall Recalls the last edited but not yet stored Live Set Sound settings. If, while editing a Live Set Sound, you select a different Live Set Sound and then return to the one currently being edited, the latest stored version will be called up instead of the current one. If this occurs, use this function to restore the Live Set Sound setting you are currently editing. NOTICE The latest edited Live Set Sound will be lost when the CK is turned off. Menu Initialize Resets the settings of MENU screens to the default values. Factory Reset Restores the CK including all Live Set Sounds to its factory default. Advanced settings CK88 CK61 Owner’s Manual 41 File * You can load a single Live Set Sound you choose from a file containing multiple Live Set Sounds such as Backup file, Live Set All file , and Live Set Page file . Bluetooth *1 When the Switch is set to Off , Volume and Pairing will be hidden. Version Info Shows the version of the CK’s firmware. Function name Description Back Up File Save Saves all the Live Set settings and other settings for the entire instrument stored in the CK to a USB flash drive as a backup file (with the extension .Y1A). Load (*) Loads the settings to the CK from a backup file saved on a USB flash drive. Live Set All File Save Saves all the Live Set settings stored in the CK to a USB flash drive as a Live Set All File (with the extension .Y1L). Load (*) Loads the settings to the CK from a Live Set All File saved on a USB flash drive. Live Set Page File Save Saves the currently selected Live Set Page stored in the CK to a USB flash drive as a Live Set Page File (with the extension .Y1P). Load (*) Loads the settings to the CK from a Live Set Page File saved on a USB flash drive. Live Set Sound File Save Saves the currently selected Live Set Sound stored in the CK to a USB flash drive as a Live Set Sound File (with the extension .Y1S). Load Loads the settings to the CK from a Live Set Sound File saved on a USB flash drive. File Utility Rename Changes the name of a file in a USB flash drive. Delete Deletes a file in a USB flash drive. Format Formats (initializes) a USB flash drive. Formatting is required when using a new USB flash drive. NOTICE When a USB flash drive is formatted, all of its content will be deleted. Make sure before formatting that the USB flash drive contains no irreplaceable data. Function name Description Switch Switches the Bluetooth function on/off. Settings: Off , On Default: Off Volume *1 Adjusts the Bluetooth audio volume. Settings: 0–127 Default: 64 Pairing *1 Pairs with the Bluetooth -equipped device. Advanced settings CK88 CK61 Owner’s Manual 42 Shortcut operations By using the buttons or knob, while holding down the [ENTER] button, you can use the shortcut operations to access the functions in the Live Set Sound SETTINGS. When using Tempo Delay for DELAY Locations Operations Descriptions Transpose & Octave [ENTER] button + TRANSPOSE [−] button Transposes the pitch of the keyboard up or down in semitones. This operation is the same as Sound Transpose . NOTE The value is not transmitted as a MIDI message. [ENTER] button + TRANSPOSE [+] button TRANSPOSE buttons [−] + [+] (together) Keyboard Transpose is set to “0.” Part select button ([A]–[C]) + OCTAVE [−] button Shifts the octave range of the specified Part up or down. This operation is the same as setting the Note Shift to “+12” or “−12.” The Note Shift range is from −12 to +12. NOTE The value is not transmitted as a MIDI message. Part select button ([A]–[C]) + OCTAVE [+] button OCTAVE buttons [−] + [+] Keyboard Octave is set to “0.” Organ [ENTER] button + VIBRATO/CHORUS [TYPE] button Switches the Vibrato/Chorus type in reverse order. This is useful when you want to return to the previous type. Live Set Pressing two or three Part select buttons ([A]–[C]) at once Selects multiple Parts at once. Useful for selecting the same settings for Filter, EG, and Insertion Effects. Holding down two of the Part select buttons ([A]–[C]) at once Swaps the settings of the selected Parts. This operation is the same as [MENU] button  Job  Part/Effect Manager  Swap Part . [ENTER] button + [SETTINGS] button Resets the Live Set Sound currently being edited to its default state. This operation does not overwrite the stored Live Set Sound. This operation is useful when you want to reset all values to start over. NOTE To reset both the Live Set Sound currently being edited as well as the stored Live Set Sound, use the [MENU] button  Job  Live Set Manager  Initialize (page 40). [ENTER] button + [MENU] button Determines whether the panel lock function is enabled (On) or disabled (Off ). [ENTER] button + MONO [TYPE] button Opens the Portamento Time setting screen. [ENTER] button + UNISON [TYPE] button Opens the Unison Detune setting screen. PAGE buttons [ ] + [ ] Shows the Live Set View. To close the Live Set View, press the [EXIT] button. Effect [ENTER] button + EFFECT1–EFFECT2 select button Swaps the settings of EFFECT 1 and EFFECT 2 in the selected Part. This operation is useful when you want to change the order in which the two Insertion Effects are applied. This operation is the same as the [MENU] button  Job  Part/Effect Manager  Swap EFFECT 1/2 . [ENTER] button + Effect [TYPE] knob Moves to the beginning of the next or previous category. This operation is useful when you want to quickly switch to the desired type. For more information on Insertion Effect Types, see the “Effect list” (page 43). Operations Descriptions [ENTER] button Use the [ENTER] button as a Tap button. Press the button at least three times to set the tempo. [ENTER] button + DELAY [TIME] knob Changes the Tempo Delay Time . Advanced settings CK88 CK61 Owner’s Manual 43 Effect list  Effect diagram Category Type Description Stereo/ Mono Chorus G Chorus Chorus effect that produces a deep sound with complex modulation. Turn the [DEPTH] knob to adjust the depth, and the [RATE] knob to adjust the speed. Stereo SPX Chorus Chorus effect that uses a three-phase LFO to create a richer and warmer sound, with a wider stereo spread. Turn the [DEPTH] knob to adjust the depth, and the [RATE] knob to adjust the speed. Stereo Symphonic Chorus effect that features multiple sound modulations to give a greater sense of spaciousness. Turn the [DEPTH] knob to adjust the depth, and the [RATE] knob to adjust the speed. Stereo 816 Chorus Chorus effect that simulates the detuned FM chorus of the TX816. Turn the [DEPTH] knob to adjust the modulation depth, and the [RATE] knob to adjust the speed. Stereo Flanger VCM Flanger Vintage flanger effect featuring a warm analog sound. Turn the [DEPTH] knob to adjust the depth and feedback level, and the [RATE] knob to adjust the speed. Stereo Cross FB Flanger Vintage flanger effect featuring a complex sound by cross feedback. Turn the [DEPTH] knob to adjust the depth and feedback level, and the [RATE] knob to adjust the speed. Stereo Phaser VCM Stereo Phaser Vintage phaser effect featuring a warm analog sound. Turn the [DEPTH] knob to adjust the depth and feedback level, and the [RATE] knob to adjust the speed. Stereo Small Phaser Vintage phaser effect that features a smooth and unique sweeping effect. Turn the [DEPTH] knob to switch the modulation type—which differs depending on whether the knob is set to the left or the right—and turn the [RATE] knob to adjust the speed. Mono Max90 Classic vintage phaser effect. Turn the [DEPTH] knob to switch the feedback level type—which differs depending on whether the knob is set to the left or the right—and turn the [RATE] knob to adjust the speed. Mono Dual Phaser Vintage phaser effect that features two phasers with different characteristics. Turn the [DEPTH] knob to adjust the speed of the phaser 1, and the [RATE] knob to adjust the speed of the phaser 2. Mono Trm/Rtr Tremolo A modulation effect that changes the volume cyclically. Turn the [DEPTH] knob to adjust the depth, and the [RATE] knob to adjust the speed. Stereo Auto Pan A modulation effect that moves the sound in the stereo field cyclically left and right. Turn the [DEPTH] knob to adjust the width for the stereo field, and the [RATE] knob to adjust the speed. Stereo Simple Rotary Simple rotary speaker effect. Turn the [DEPTH] knob to adjust the volume and distortion level, and the [RATE] knob to adjust the rotation speed. Mono * * Available only for the Organ Voices using the Organ Flutes tone generator (H, V, F, A, and Y). Send Level is the same for all parts EQUALIZER Delay Reverb Voice Drive Effect1 Effect2 Vibrato/ Chorus A/D Input Noise Gate Input EQ Input Effect 1 Input Effect 2 Audio Trigger Part A Part C Part B Advanced settings CK88 CK61 Owner’s Manual 44 Dist British Combo Warm distortion effect (overdrive). Turn the [DEPTH] knob to adjust the distortion level, and the [RATE] knob to adjust the brilliance (brightness of the sound). Mono British Lead Hard rock type distortion effect. Turn the [DEPTH] knob to adjust the distortion level, and the [RATE] knob to adjust the treble (attack for the high band). Mono Small Stereo Stereo distortion effect. Turn the [DEPTH] knob to adjust the distortion level, and the [RATE] knob to adjust the presence (clearness of sound). Stereo Comp/EQ Compressor Stereo compressor. Turn the [DEPTH] knob to adjust the threshold, and the [RATE] knob to adjust the output volume. Stereo Tone Control Shelving equalizer. Use the [DEPTH] knob to adjust the low band, and the [RATE] knob to adjust the high band. Stereo 1 Band EQ Narrow Peaking equalizer with narrow Q (bandwidth). Use the [DEPTH] knob to adjust the gain, and the [RATE] knob to adjust the center frequency. Stereo 1 Band EQ Wide Peaking equalizer with wide Q (bandwidth). Use the [DEPTH] knob to adjust the gain, and the [RATE] knob to adjust the center frequency. Stereo Wah Auto Wah Wah modulation effect that changes cyclically. Turn the [DEPTH] knob to adjust the resonance level, and the [RATE] knob to adjust the speed. Stereo Touch Wah Wah effect that responds to volume changes by keyboard touch. Turn the [DEPTH] knob to adjust the sensitivity, and the [RATE] knob to adjust the resonance level. Stereo Pedal Wah Wah effect that is pedal-controlled. Turn the [DEPTH] knob to adjust the distortion level, and the [RATE] knob to adjust the resonance level. The pedal wah effect can be controlled with a pedal if Foot Pedal Assign is set to 4 (Pedal Wah). Stereo Delay Digital Delay Clean digital delay. Turn the [DEPTH] knob to adjust the depth and feedback level, and the [RATE] knob to adjust the delay time. Stereo Analog Delay Delay featuring a warm analog sound. Turn the [DEPTH] knob to adjust the feedback level, and the [RATE] knob to adjust the delay time. Stereo Cross Delay Delay that alternates between the left and right. Turn the [DEPTH] knob to adjust the depth and feedback level, and the [RATE] knob to adjust the delay time. Stereo Reverb Hall Reverb Simulates the reverberation of a hall. Turn the [DEPTH] knob to adjust the depth, and the [RATE] knob to adjust the reverb time (reverberation length). Stereo Room Reverb Simulates the reverberation of a room. Turn the [DEPTH] knob to adjust the depth, and the [RATE] knob to adjust the reverb time (reverberation length). Stereo Reverse Reverb The effect that simulates reverse playback Gated Reverb. Turn the [DEPTH] knob to adjust the depth, and the [RATE] knob to adjust the reverb time (reverberation length). Stereo Others Ring Modulator An effect that changes the sound in metallic and wildly distorting synth ways. Turn the [DEPTH] knob to adjust the depth, and the [RATE] knob to adjust the frequency. Stereo Slicer An effect that slices the input sound into rhythmically interrupted segments. Turn the [DEPTH] knob to adjust the gate time (length for the sliced note), and the [RATE] knob to adjust the fineness of slicing. Stereo LP Filter Filter that cuts sounds at frequencies higher than the cutoff frequency. Turn the [DEPTH] knob to adjust the cutoff frequency, and the [RATE] knob to adjust the resonance. Stereo HP Filter Filter that cuts sounds at frequencies lower than the cutoff frequency. Turn the [DEPTH] knob to adjust the cutoff frequency, and the [RATE] knob to adjust the resonance. Stereo Category Type Description Stereo/ Mono Advanced settings CK88 CK61 Owner’s Manual 45 Others Lo-Fi An effect that re-samples and degrades the input sound.Turn the [DEPTH] knob to adjust the coarseness of the sound, and the [RATE] knob to adjust the sampling frequency. Turn each knob clockwise to make them sound more degraded and less clear. Mono Damper Resonance An effect that reproduces the sound produced by open strings of a piano while the damper pedal is pressed. Turn the [DEPTH] knob to adjust the depth, and the [RATE] knob to adjust the damper openness. Stereo Harmonic Enhancer An effect that adds harmonic overtones to the input sound to makes the sound stand out. Turn the [DEPTH] knob to adjust the cutoff frequency of the high-pass filter, and the [RATE] knob to adjust the effect level. Stereo Category Type Description Stereo/ Mono CK88 CK61 Owner’s Manual 46 By connecting external devices, you can take advantage of various convenient and powerful features of the CK. For example, you can: • Play the CK along with the songs played on your smartphone or a portable music player. • Use smart device apps to manage the Live Set Sounds, create videos, and post videos on social media. • Play the CK using sounds on external sound modules or other synthesizers. • Play the CK sounds from an external keyboard. Using Smart Devices There are two ways of connecting a smart device: wireless connection via Bluetooth Audio and wired connection using a USB cable. For more information on smart device applications that you can use with the CK, refer to the following website. https://www.yamaha.com/kbdapps/ NOTICE Be sure to place your smart device on a stable surface to prevent it from falling over and being damaged. NOTE To eliminate the risk of interference due to noise by your smart device when used in combination with the CK, turn on the Airplane Mode and then turn on Wi-Fi. Connecting via Bluetooth audio  Bluetooth capability Depending on the country in which you purchased the product, the CK may not have Bluetooth capability. By using the Bluetooth audio function, you can connect a Bluetooth-equipped device such as a smartphone and portable audio player wirelessly to the CK and use the speakers on the CK to play back the audio from the Bluetooth device. NOTE • Bluetooth headphones or speakers cannot be connected. • There is no Bluetooth MIDI capability on the CK.  Pairing with a Bluetooth-equipped device “Pairing” means registering Bluetooth-equipped smart devices on the CK and establish mutual recognition for wireless communication between the two. Once the device is paired with the CK, it is not necessary to pair the two again (unless you’ve disabled pairing.) 1. Select the setting from the [MENU] button  Bluetooth  Switch to On  press the [ENTER] button  Pairling . The CK will be paired, and the “ Bluetooth pairing... ” message will appear on the display. To cancel the pairing, press the [EXIT] button. 2. Turn the Bluetooth setting ON on the Bluetooth-equipped device and select CK61 or CK88 from the list. • Make sure to complete the settings on the smart device within a minute. After that, the pairing mode ends automatically. • If you are required to enter a passkey, enter the numerals “0000.” When the pairing is completed, the (Bluetooth) mark appears on the top screen. Use the Bluetooth-equipped device to adjust the volume of the sound input via Bluetooth. To adjust Using with External Devices Precautions when using the USB [TO HOST] terminal When connecting the computer to the USB [TO HOST] terminal, make sure to observe the following points to avoid freezing the computer/ instrument and corrupting or losing the edited settings in SETTINGS. NOTICE • Use an AB type USB cable of less than 3 meters. USB 3.0 cables cannot be used. • Perform the following before turning the power to the instrument on/off or plugging/unplugging the USB cable to/from the USB [TO HOST] terminal. - Quit any open application software on the computer. - Make sure that MIDI data is not being transmitted from the instrument. (MIDI data is transmitted when the notes on the keyboard are played.) • While the computer is connected to the instrument, you should wait for six seconds or more between these operations: (1) when turning the power of the instrument off then on again, or (2) when alternately connecting/disconnecting the USB cable. If the computer or the instrument freezes, restart the application software or the computer OS or turn the power to the instrument off then on again. Using with External Devices CK88 CK61 Owner’s Manual 47 the volume balance between the sound input via Bluetooth and your performance on the CK, you can also use the [MENU] button  Bluetooth  Volume . 3. Playback audio on the Bluetooth-equipped device to confirm that the built-in speakers or the headphones connected to the CK can output the audio sound. When you turn on the CK the next time, the last connected smart device will be connected to the CK automatically if the Bluetooth function of the smart device and the CK are set to on. If it is not connected automatically, select the model name of the CK from the connection list on the smart device.  Switching the Bluetooth off Select the setting from the [MENU] button  Bluetooth  Switch to Off . Connecting using the USB [TO HOST] terminal For more information on how to connect a device to the USB [TO HOST] terminal, refer to the “Smart Device Connection Manual.”  Smart Device Connection Manual Access the website below and then open “Manual Library.” Select your language, and then enter “smart device” in the “Model Name or Keyword” field and finally click “Search.” https://download.yamaha.com/ For setting the sound input from the USB audio to output to the computer or smart device connected to the USB [TO HOST] jack of the CK, set from the [MENU] button  General  Audio  USB Audio Loopback (page 38). Connecting to a computer By connecting the CK to your computer, you can expand your musical possibilities by using music production software or DAWs. Here are some of the creative options you can explore. • Recording your performance to a DAW • Playing the software synthesizer from the CK • Playing the internal sound generator of the CK from a DAW A USB cable and the Yamaha Steinberg USB Driver are necessary to connect the CK to the computer. Follow the instructions below to make the connection. Before connecting the USB [TO HOST] terminal to a computer, be sure to read “Precautions when using the USB [TO HOST] terminal” on page 46. 1. Download the latest Yamaha Steinberg USB Driver from the URL below. https://download.yamaha.com/ NOTE • For more information on the system requirements for the Yamaha Steinberg USB Driver, refer to the URL above. • The Yamaha Steinberg USB Driver may be revised and updated without prior notice. For details and the latest information, refer to the URL above. 2. Install the Yamaha Steinberg USB Driver on your computer. Refer to the Installation Guide included in the downloaded file. 3. Change the settings from the [MENU] button  General  MIDI  MIDI Port  USB to On to set the CK to send and receive MIDI through the USB [TO HOST] terminal. Controlling a synthesizer or tone generator module from the CK You can play the sounds of an external MIDI tone generator by playing on the CK’s keyboard. By setting the [MENU] button  General  MIDI  MIDI Control to On (page 37), you can use the ORGAN FOOTAGE sliders and knobs for Filter and EG, for example, for controlling an external device. CK61 MIDI [IN] terminal Synthesizer or tone generator module, etc. MIDI [OUT] terminal Using with External Devices CK88 CK61 Owner’s Manual 48 Controlling the CK from an external keyboard By combining with another keyboard, you can have the two connected instruments function like a two- manual organ. For example, if you wish to play both the CK and the other instrument by setting the [SETTINGS] button  Function  External Keyboard (page 32) to Ext+Int , or to play only the other instrument by setting to ExtOnly . Setting the MIDI transmit and receive channels To control a device using MIDI, you must set the transmit channel on the controlling device and the receive channel on the controlled device to match. You can change the transmit channel (Tx) and receive channel (Rx) on the CK from the [MENU] button  General  MIDI  MIDI Channel . NOTE For details on setting the transmit channel of an external MIDI keyboard or the receive channel of an external MIDI tone generator, refer to the owner’s manual of that device. Disabling the internal tone generator sound when the built-in keyboard is played If you want only the external tone generator connected to the MIDI [OUT] terminal or USB [TO HOST] terminal to produce sound when the keyboard of the CK is played, you can lower the CK’s volume, or turn off all Parts, or set the value for Local Control under the [MENU] button  General  MIDI  Local Control to Off (page 37). The last method is especially convenient when recording with a DAW. Setting how the MIDI terminals are used (MIDI Port settings) The CK provides two MIDI ports, each with different purposes. • Port 1: For communication between the CK and a computer. • Port 2: For communication between a computer and an external MIDI device by using the CK. You can set whether to use the MIDI terminals as Port 1 or Port 2, from the [MENU] button  General  MIDI  MIDI Port  MIDI (page 37). Initially, it is set to Port 1.  Port 1 Use this Port to control the tone generator of the CK from an external device, or to control an external tone generator from the CK. Set the value under the [MENU] button  General  MIDI  MIDI Port  MIDI to On .  Port 2 Use this port when you want to connect an external MIDI device to a computer via the CK. Set the values under the [MENU] button  General  MIDI  MIDI Port as follows. • MIDI: Off • USB: On Example CK61 MIDI [IN] terminal External keyboard MIDI [OUT] terminal CK61 MIDI [IN] terminal External MIDI device such as tone generator USB [TO HOST] terminal MIDI [OUT] terminal USB cable USB terminal Computer CK88 CK61 Owner’s Manual 49 Live Set Sound List CK88 Data List Page No. Name Split Point Part Voice Name MSB LSB PC 1 1 CFX Grand G2 A CFX Stereo 63 0 1 B – C – 1 2 Mono U1 G2 A U1 63 0 2 B – C – 1 3 CF3 Pad G2 A Live CF3 63 0 3 B Back Pad C – 1 4 Acoustic Split G2 A Acoustic Bass 63 0 4 B U1 C H 1 5 Panning Tines G2 A 78Rd 63 0 5 B – C – 1 6 Warm Reeds G2 A Wr Warm 63 0 6 B – C – 1 7 Jazz Split C3 A H 63 0 7 B H C – 1 8 Orchestra G2 A Orchestra 2 63 0 8 B Concert Str C Horn Section 2 1 S700 Grand G2 A S700 63 1 1 B – C – 2 2 Rock Piano G2 A Live CF3 63 1 2 B – C – 2 3 80’s Layer G2 A CFX St Bright 63 1 3 B 73Rd Studio C – 2 4 DX/Minilead G2 A DX 7 II 63 1 4 B Classic Mini C – 2 5 78Rd Chorus G2 A 78Rd 63 1 5 B – C – 2 6 Funky Land Clav G2 A Clavi S 63 1 6 B – C – 2 7 Rock Rotary G2 A H 63 1 7 B – C – 2 8 Brass Section G2 A BrassSection5 63 1 8 B – C – Page No. Name Split Point Part Voice Name MSB LSB PC 3 1 CP80 Dirty Funk G2 A CP80 1 63 2 1 B – C – 3 2 Phasing 73 G2 A 73Rd Studio 63 2 2 B – C – 3 3 Fusion Layer G2 A 73Rd Studio 63 2 3 B OB Brass 1 C – 3 4 EDM Pluck Split G2 A Synth Bass 2 63 2 4 B Popcorn C Sky Walk 3 5 Amped Tines G2 A 73Rd Studio 63 2 5 B – C – 3 6 The Red Organ G2 A V 63 2 6 B – C – 3 7 JP Strings G2 A JP Strings 63 2 7 B – C – 3 8 Soft Synth Lead G2 A Wire Lead 63 2 8 B – C – Data List CK88 CK61 Owner’s Manual 50 CK61 CK88 CK61 Page No. Name Split Point Part Voice Name MSB LSB PC 1 1 CFX Grand G2 A CFX Stereo 63 0 1 B – C – 1 2 Panning Tines G2 A 78Rd 63 0 2 B – C – 1 3 Warm Reeds G2 A Wr Warm 63 0 3 B – C – 1 4 80’s Layer G2 A CFX St Bright 63 0 4 B 73Rd Studio C – 1 5 Funky Land Clav G2 A Clavi S 63 0 5 B – C – 1 6 Brass Section G2 A BrassSection5 63 0 6 B – C – 1 7 Jazz Split C3 A H 63 0 7 B H C – 1 8 Soft Synth Lead G2 A Wire Lead 63 0 8 B – C – 2 1 S700 Grand G2 A S700 63 1 1 B – C – 2 2 78Rd Chorus G2 A 78Rd 63 1 2 B – C – 2 3 CP80 Dirty Funk G2 A CP80 1 63 1 3 B – C – 2 4 CF3 Pad G2 A Live CF3 63 1 4 B Back Pad C – 2 5 Amped Tines G2 A 73Rd Studio 63 1 5 B – C – 2 6 JP Strings G2 A JP Strings 63 1 6 B – C – 2 7 Rock Rotary G2 A H 63 1 7 B – C – 2 8 Orchestra G2 A Orchestra 2 63 1 8 B Concert Str C Horn Section 3 1 Mono U1 G2 A U1 63 2 1 B – C – 3 2 Rock Piano G2 A Live CF3 63 2 2 B – C – 3 3 Phasing 73 G2 A 73Rd Studio 63 2 3 B – C – 3 4 DX/Minilead G2 A DX 7 II 63 2 4 B Classic Mini C – 3 5 Acoustic Split G2 A Acoustic Bass 63 2 5 B U1 C H 3 6 Fusion Layer G2 A 73Rd Studio 63 2 6 B OB Brass 1 C – 3 7 The Red Organ G2 A V 63 2 7 B – C – 3 8 EDM Pluck Split G2 A Synth Bass 2 63 2 8 B Popcorn C Sky Walk Page No. Name Split Point Part Voice Name MSB LSB PC 4 1 Live CF3 Grand G2 A Live CF3 63 3 1 B – C – 4 2 Pretty Upright G2 A U1 63 3 2 B – C – 4 3 Honky Dogs G2 A S700 63 3 3 B U1 C – 4 4 House Piano G2 A Digi Piano 2 63 3 4 B – C – 4 5 Bubble Rds C4 A 78Rd 63 3 5 B – C – 4 6 Bright Reeds G2 A Wr Bright 63 3 6 B – C – 4 7 Clavi S G2 A Clavi S 63 3 7 B – C – 4 8 Trippy DX G2 A DX Legend 63 3 8 B – C – 5 1 Comping Drawbar G2 A H 63 4 1 B – C – 5 2 Jazz Swish G2 A H 63 4 2 B – C – 5 3 Gospel Layers G2 A H 63 4 3 B H C – 5 4 Lead Organ G2 A H 63 4 4 B – C – 5 5 British Organ G2 A V 63 4 5 B – C – 5 6 Aged Tone Organ G2 A A 63 4 6 B A C – 5 7 Concert Organ G2 A Concert Organ 63 4 7 B Church Organ1 C Church Organ1 5 8 Big Pipes G2 A Organo Pleno 63 4 8 B Concert Organ C – 6 1 Echo Guitar G2 A Nylon Guitar1 63 5 1 B – C – 6 2 Acoustic Steel G2 A Steel Gt 2 63 5 2 B – C – 6 3 Clean El-Gtr G2 A Clean Gt 1 63 5 3 B – C – 6 4 Overdrive Gtr G2 A Clean Gt 3 63 5 4 B – C – 6 5 Slap Bass G2 A Slap Bass 63 5 5 B – C – 6 6 101 Bass G2 A Synth Bass 3 63 5 6 B Fundamental C – 6 7 Mini Bass G2 A Unison Bass 63 5 7 B – C – 6 8 Click Syn Bass G2 A Click SynBass 63 5 8 B – C – Data List CK88 CK61 Owner’s Manual 51 7 1 Quartet Strings G2 A Quartet 63 6 1 B – C – 7 2 Ancient Sampler G2 A Tron Strings 63 6 2 B – C – 7 3 On top G2 A Orchestra 1 63 6 3 B Oboe C French Horn 7 4 2310 Orchestra G2 A Alto Flute 63 6 4 B Orchestra 2 C Section Str 2 7 5 Party Brass G2 A BrassSection2 63 6 5 B Forte Brass C BrassSection3 7 6 Sax Section G2 A Sax Section 2 63 6 6 B – C – 7 7 Flute G2 A Flute 1 63 6 7 B – C – 7 8 Epic Calliope G2 A Calliope Ld 1 63 6 8 B – C – 8 1 Comp and Solo G2 A 73Rd Studio 63 7 1 B Dynmic Mini C – 8 2 Nu Saw Lead C3 A – 63 7 2 B Saw Lead 1 C – 8 3 Arena Lead G2 A Dancy Hook 63 7 3 B – C – 8 4 Vx Based PolyLd C4 A – 63 7 4 B – C V 8 5 Analog Pad G2 A Soft Pad 2 63 7 5 B – C – 8 6 Zen Pad C4 A Atmosphere 63 7 6 B ZEN C – 8 7 Magic Bells Pad G2 A Bell Pad 1 63 7 7 B Slow Choir C Glocken 1 8 8 Slow Choir G2 A Slow Choir 63 7 8 B – C – 9 1 OB Brass G2 A OB Brass 1 63 8 1 B – C – 9 2 Synth F.Horns G2 A Analog Brass1 63 8 2 B – C – 9 3 Jumping Synths G2 A Jump Brass 63 8 3 B – C – 9 4 Synth Strings G2 A Analog Str 63 8 4 B Syn Strings 1 C – 9 5 Warm Analog Str G2 A Lite Strings2 63 8 5 B Back Pad C – 9 6 Mallet Lead G2 A Marimba 1 63 8 6 B – C – 9 7 Dream Vibes G2 A Vibraphone 63 8 7 B – C – 9 8 Enchantment G2 A Glocken 1 63 8 8 B – C – Page No. Name Split Point Part Voice Name MSB LSB PC 10 1 Sweet Piano G2 A S700 63 9 1 B Warm Strings C – 10 2 BrghtPianoLayer G2 A CFX Stereo 63 9 2 B CP80 1 C DX Woody 10 3 80’s CP Brassy G2 A CP80 1 63 9 3 B Synth Brass 2 C – 10 4 Gtr Pad Strings G2 A Classic Gt 63 9 4 B Soft Pad 2 C Warm Strings 10 5 Slow Piano Pad G2 A Live CF3 63 9 5 B V C Ring Pad 10 6 Cinematic G2 A High Brass 63 9 6 B Orchestra 1 C – 10 7 Ambient Piano G2 A CFX St Warm 63 9 7 B CFX St Warm C Balimba 10 8 Tricky Piano G2 A CFX Stereo 63 9 8 B – C – Page No. Name Split Point Part Voice Name MSB LSB PC Data List CK88 CK61 Owner’s Manual 52 Voice List Category Sub Category No Name Parameter Value Piano Grand 1 CFX Stereo 0 2 CFX St Bright 1 3 CFX St Warm 2 4 CFX Mono 3 5 CFX Mn Bright 4 6 CFX Mn Warm 5 7 S700 6 8 Live CF3 7 9 Digi Piano 1 8 10 Digi Piano 2 9 Upright 11 U1 10 CP 12 CP80 1 11 13 CP80 2 12 E.Piano Rd 1 78Rd 13 2 73Rd Studio 14 Wr 3 Wr Warm 15 4 Wr Bright 16 Clavi 5 Clavi B 17 6 Clavi S 18 7 Harpsi 1 19 8 Harpsi 2 20 FM 9 DX Legend 21 10 DX Woody 22 11 DX FTine 23 12 DX 7 II 24 13 DX Mellow 25 14 DX Crisp 26 Organ Tone Wheel 1 H 27 Combo 2 V 28 3 F 29 4 A 30 5 Y 31 Pipe 6 Pipe Organ 1 32 7 Pipe Organ 2 33 8 Concert Organ 34 9 Grand Jeu 35 10 FondsEtAnches 36 11 Organo Pleno 37 12 Diapason 38 13 Claribel&Flut 39 14 Soft Reeds 40 15 Church Organ1 41 16 Church Organ2 42 17 Church Organ3 43 18 Church Organ4 44 Accordion 19 Accordion 45 20 Musette 46 Brs/Wind (Brass/ Woodwind) Ensemble 1 BrassSection1 47 2 BrassSection2 48 3 BrassSection3 49 4 BrassSection4 50 5 BrassSection5 51 6 Sfz Brass 52 7 Forte Brass 53 8 SforzandoFall 54 9 High Brass 55 10 Mellow Brass1 56 11 Mellow Brass2 57 12 Soft Brass 58 13 Tp&Tb Section 59 14 Trb. Section 60 15 Horn Section 61 16 Horn Strings 62 17 Brass Strings 63 Category Sub Category No Name Parameter Value Brs/Wind (Brass/ Woodwind) Solo 18 Sweet Trumpet 64 19 Trumpet 65 20 Trombone 66 21 French Horn 67 22 Horn 68 Saxophone 23 Sax Section 1 69 24 Sax Section 2 70 25 Sax Section 3 71 26 Sweet Alto 72 27 Alto Sax 73 28 Tenor Sax 1 74 29 Tenor Sax 2 75 30 Soprano Sax 76 31 Baritone Sax 77 Woodwind 32 Oboe 78 33 Bassoon 79 34 Clarinet 80 35 Flute 1 81 36 Flute 2 82 37 Alto Flute 83 38 Tape Flute 84 39 Recorder 85 40 Pan Flute 1 86 41 Pan Flute 2 87 42 Bottle 88 43 Shakuhachi 89 44 Ocarina 90 45 Harmonica 1 91 46 Harmonica 2 92 47 Bagpipe 93 Synth 48 Synth Brass 1 94 49 Synth Brass 2 95 50 Synth Brass 3 96 51 Synth Brass 4 97 52 Jump Brass 98 53 OB Brass 1 99 54 OB Brass 2 100 55 OB Brass 3 101 56 OB Brass 4 102 57 OB Brass 5 103 58 SoftSynBrs 1 104 59 SoftSynBrs 2 105 60 Big Squish 106 61 Analog Brass1 107 62 Analog Brass2 108 Gtr/Bass (Guitar/ Bass) Guitar 1 Classic Gt 109 2 Nylon Guitar1 110 3 Nylon Gt Harm 111 4 Nylon Guitar2 112 5 Steel Gt 1 113 6 Steel Gt 2 114 7 Steel Gt 3 115 8 12 Str Gt 1 116 9 12 Str Gt 2 117 10 Clean Gt 1 118 11 Clean Gt 2 119 12 Clean Gt 3 120 13 60's Clean Gt 121 14 Funk Guitar 122 15 12 Str Clean 123 16 Dist Guitar 1 124 17 Dist Guitar 2 125 18 Over The Top 126 19 Crunch Guitar 127 20 Crunch Oct 128 21 Mute Dist 129 22 Jazz Guitar 130 23 Hawaiian Gt 131 Category Sub Category No Name Parameter Value Gtr/Bass (Guitar/ Bass) Bass 24 Acoustic Bass 132 25 Upright Bass 133 26 Finger Bass 1 134 27 Finger Bass 2 135 28 Finger Bass 3 136 29 Finger Bass 4 137 30 Pick Bass 1OM 138 31 Pick Bass 1 M 139 32 Pick Bass 1 O 140 33 Pick Bass 2 141 34 Slap Bass 142 35 Fretless Ba 1 143 36 Fretless Ba 2 144 Bass +Drum 37 A.Bass + Cym 145 38 E.Bass + Cym 146 Synth 39 Synth Bass 1 147 40 Synth Bass 2 148 41 Synth Bass 3 149 42 Synth Bass 4 150 43 Synth Bass 5 151 44 Big Bass 152 45 101 Bass 153 46 Competitor 154 47 Perc Punch 155 48 Trance Bass 156 49 Dark Bass 157 50 Click SynBass 158 51 Acid Bass 159 52 Square Bass 160 53 Long Spit 161 54 Fundamental 162 55 One Voice 163 56 Fat Sine 164 57 Fat Sine Res 165 58 Unison Bass 166 Strings Ensemble 1 Section Str 1 167 2 Section Str 2 168 3 Section Str 3 169 4 Strings 1 170 5 Strings 2 171 6 Orchestra 1 172 7 Orchestra 2 173 8 Arco String 174 9 Fast Strings 175 10 Marcato Str 176 11 Concert Str 177 12 Legato Str 178 13 Warm Strings 179 14 Slow Str 1 180 15 Slow Str 2 181 16 Slow Str 3 182 17 60's Strings 183 18 70's Strings1 184 19 70's Strings2 185 20 SlwAtkTremolo 186 21 Tremolo Str 187 22 Velo Strings 188 23 Quartet 189 24 Tron Strings 190 25 Tape Strings 191 26 Flute Strings 192 Solo 27 Sweet Violin 193 28 Violin 194 29 Cello 195 Pizzicato 30 Pizzicato 1 196 31 Pizzicato 2 197 32 Harp 198 Data List CK88 CK61 Owner’s Manual 53 Strings Synth 33 Syn Strings 1 199 34 Syn Strings 2 200 35 Syn Strings 3 201 36 Analog Str 202 37 Lite Strings1 203 38 Lite Strings2 204 39 JP Strings 205 40 Pop Syn Str 206 41 Unison Str 207 42 Oct Syn Str 208 Pad Pad 1 Bell Pad 1 209 2 Bell Pad 2 210 3 BrightPadBell 211 4 Sharp Teeth 212 5 Ring Pad 213 6 Anlg Rez Pad 214 7 LFO Pad 215 8 Chill Scap 216 9 Strings Pad 217 10 Back Pad 218 11 Planet 219 12 Atmosphere 220 13 Click Pad 221 14 Pad 80 222 15 Poly Pad 223 16 Glass Harp 224 17 Digi Stuff 225 18 New Age Pad 226 19 Darklight 227 20 Neo Crystal 228 21 Vapor 229 22 Soft Pad 1 230 23 Soft Pad 2 231 24 VP Soft 232 25 Glass Pad 233 26 Sine Pad 234 27 Echoes 235 28 Ambient Pad 236 29 Pan Pad 237 30 Sci-Fi 238 31 Big Pan 239 32 Goblins 240 33 Sweep Pad 1 241 34 Sweep Pad 2 242 35 Nowhere 243 36 Goblins Synth 244 37 Celestial 245 38 Converge 246 39 Creation 247 40 Ancestral 248 41 Soundtrack 249 42 Echo Pad 250 43 Rain 251 44 Analog Pad 252 45 Dark Light 253 46 Digi Pad 254 47 Noble Pad 255 48 Pop Pad 256 49 Fat Saw 257 50 Angel Pad 258 Category Sub Category No Name Parameter Value Pad Choir 51 Choir 1 259 52 Choir 2 260 53 Choir 3 261 54 Air Choir 262 55 Choir Aah 263 56 Voice Oohs 264 57 Slow Vox 265 58 Slow Choir 266 59 Itopia 267 60 Mystic Pad 268 Sound FX 61 Twist 269 62 Da Pad 270 63 Dark Star 271 64 Mind Bell 272 65 ZEN 273 Lead Analog 1 Dancy Hook 274 2 Faaat Dance 275 3 Techno Brass 276 4 After 1984 277 5 Analog Lead 1 278 6 Analog Lead 2 279 7 Analog Lead 3 280 8 Analog Lead 4 281 9 Saw Lead 1 282 10 Saw Lead 2 283 11 Saw Lead 3 284 12 Wire Lead 285 13 Classic Mini 286 14 Big Lead 1 287 15 Big Lead 2 288 16 Early Lead 289 17 Troy 290 18 Sync Saw Lead 291 19 Punch Lead 292 20 Soft RnB 293 21 Popcorn 294 22 Synth Trumpet 295 23 Dynmic Mini 296 24 Crying 297 25 Funky Mini 298 26 Funky Poly 299 27 Mini Three 300 28 Nu Mini 301 29 Sky Walk 302 30 Mini Soft 303 31 Mini Lead 304 32 Inda Night 305 33 Sine Lead 306 34 Tiny Lead 307 35 Synth Whistle 308 36 Raplead 309 37 Funk Lead 1 310 38 Funk Lead 2 311 39 Rezz Punch 312 40 Square Lead 1 313 41 Square Lead 2 314 42 Square Lead 3 315 43 Soft Square 316 44 5th Lead 317 Digital 45 Digital Lead 318 46 Voice Lead 319 47 Wind Lead 320 48 Calliope Ld 1 321 49 Calliope Ld 2 322 50 Orchestra Hit 323 51 Impact 324 Category Sub Category No Name Parameter Value Chr.Perc (Chromatic Percussion) Mallet 1 Marimba 1 325 2 Marimba 2 326 3 Xylophone 1 327 4 Xylophone 2 328 5 Balimba 329 6 Vib ST 330 7 Vibraphone 331 8 Hard Vibes 332 9 Glocken 1 333 10 Glocken 2 334 11 Music Box 335 Bell 12 Soft Crystal 336 13 Tinkle Bell 337 14 Tubular Bell 338 15 Carillon 339 Synth Bell 16 Digi Bell 1 340 17 Digi Bell 2 341 18 Digi Bell 3 342 19 Nice Bell 343 20 Stack Bell 344 21 Bell Harp 345 22 Harp Vox 346 23 Round Glock 347 24 Air Bells 348 25 Star Dust 349 26 Heaven Bell 350 Others Ethnic 1 Kalimba 351 2 Kanoon 352 3 Shamisen 353 4 Sitar 1 354 5 Sitar 2 355 6 Banjo 356 7 Mandolin 357 8 Dulcimer 358 9 Koto 359 Percussion 10 Timpani 360 11 Steel Drums 361 12 Agogo 362 Category Sub Category No Name Parameter Value Data List CK88 CK61 Owner’s Manual 54 Control Change Number * CC numbers A, B, and C correspond to each of Part A, B, and C. The parameters shown in parenthesis will not affect the internal tone generator. For parameter values, see tables A to C on the next page. CC No. Display Controllers Table A B C Rotary 9 ROTARY [STOP] button C 9 ROTARY [SPEED] button C Organ 18 77 111 ORGAN FOOTAGE slider [16'] D 19 78 112 ORGAN FOOTAGE slider [5 1/3'] D 20 79 113 ORGAN FOOTAGE slider [8'] D 21 80 114 ORGAN FOOTAGE slider [4'] D 22 81 115 ORGAN FOOTAGE slider [2 2/3'] D 23 82 116 ORGAN FOOTAGE slider [2'] D 24 83 117 ORGAN FOOTAGE slider [1 3/5'] D 25 85 118 ORGAN FOOTAGE slider [1 1/3'] D 26 86 119 ORGAN FOOTAGE slider [1'] D Volume 12 Volume Part Volume slider [A] A 27 Part Volume slider [B] A 87 Part Volume slider [C] A Filter 74 30 104 Cutoff FILTER [CUTOFF] knob A 71 31 105 Resonance FILTER [RESONANCE] knob A EG 73 28 102 Attack EG [ATTACK] knob A 72 29 103 Release EG [RELEASE] knob A Drive 13 68 106 Depth DRIVE [DEPTH] knob A Effect1 14 69 107 Depth EFFECT [DEPTH] knob A 15 70 108 Rate EFFECT [RATE] knob A Effect2 16 75 109 Depth EFFECT [DEPTH] knob A 17 76 110 Rate EFFECT [RATE] knob A Delay 93 Depth DELAY [DEPTH] knob A 92 Time DELAY [TIME] knob A Reverb 91 Depth REVERB DEPTH knob A Equalizer 90 Equalizer Gain EQUALIZER slider [LOW] B 89 EQUALIZER slider [MID] B 88 EQUALIZER slider [HIGH] B CC No. Display* Controllers Table Foot Pedal 1, Foot Pedal 2, Modulation Wheel 1 Modulation 4 Pedal Wah 5 (Portamento Time) 6 (Data Entry MSB) 7 All Volume 9 Rotary Slow/Fast ROTARY [STOP] button C ROTARY [SPEED] button C 10 (Pan) 11 Expression 12 A: Volume Part Volume slider [A] A 13 A: Drive Depth DRIVE [DEPTH] knob A 14 A: Effect1 Depth EFFECT [DEPTH] knob A 15 A: Effect1 Rate EFFECT [RATE] knob A 16 A: Effect2 Depth EFFECT [DEPTH] knob A 17 A: Effect2 Rate EFFECT [RATE] knob A 18 A: Drawbar 16' ORGAN FOOTAGE slider [16'] A 19 A: Drawbar 5 1/3 ORGAN FOOTAGE slider [5 1/3'] A 20 A: Drawbar 8' ORGAN FOOTAGE slider [8'] A 21 A: Drawbar 4' ORGAN FOOTAGE slider [4'] A 22 A: Drawbar 2 2/3 ORGAN FOOTAGE slider [2 2/3'] A 23 A: Drawbar 2' ORGAN FOOTAGE slider [2'] A 24 A: Drawbar 1 3/5' ORGAN FOOTAGE slider [1 3/5'] A 25 A: Drawbar 1 1/3' ORGAN FOOTAGE slider [1 1/3'] A 26 A: Drawbar 1' ORGAN FOOTAGE slider [1'] A CC No. Display* Controllers Table Foot Pedal 1, Foot Pedal 2, Modulation Wheel 27 B: Volume Part Volume slider [B] A 28 B: Attack EG [ATTACK] knob A 29 B: Release EG [RELEASE] knob A 30 B: Cutoff FILTER [CUTOFF] knob A 31 B: Resonance FILTER [RESONANCE] knob A 32 (Bank LSB) 38 (Data Entry LSB) 64 Sustain 65 (Portamento) 66 Sostenuto 67 Soft 68 B: Drive Depth DRIVE [DEPTH] knob A 69 B: Effect1 Depth EFFECT [DEPTH] knob A 70 B: Effect1 Rate EFFECT [RATE] knob A 71 A: Resonance FILTER [RESONANCE] knob A 72 A: Release EG [RELEASE] knob A 73 A: Attack EG [ATTACK] knob A 74 A: Cutoff FILTER [CUTOFF] knob A 75 B: Effect2 Depth EFFECT [DEPTH] knob A 76 B: Effect2 Rate EFFECT [RATE] knob A 77 B: Drawbar 16' ORGAN FOOTAGE slider [16'] A 78 B: Drawbar 5 1/3 ORGAN FOOTAGE slider [5 1/3'] A 79 B: Drawbar 8' ORGAN FOOTAGE slider [8'] A 80 B: Drawbar 4' ORGAN FOOTAGE slider [4'] A 81 B: Drawbar 2 2/3 ORGAN FOOTAGE slider [2 2/3'] A 82 B: Drawbar 2' ORGAN FOOTAGE slider [2'] A 83 B: Drawbar 1 3/5' ORGAN FOOTAGE slider [1 3/5'] A 84 (Portamento Ctrl) 85 B: Drawbar 1 1/3' ORGAN FOOTAGE slider [1 1/3'] A 86 B: Drawbar 1' ORGAN FOOTAGE slider [1'] A 87 C: Volume Part Volume slider [C] A 88 Equalizer High EQUALIZER slider [LOW] B 89 Equalizer Mid EQUALIZER slider [MID] B 90 Equalizer Low EQUALIZER slider [HIGH] B 91 Reverb Depth REVERB DEPTH knob A 92 Delay Time DELAY [DEPTH] knob A 93 Delay Depth DELAY [TIME] knob A 95 (Effect5 Depth) 96 (Data Increment) 97 (Data Decrement) 98 (NRPN LSB) 99 (NRPN MSB) 100 (RPN LSB) 101 (RPN MSB) 102 C: Attack EG [ATTACK] knob A 103 C: Release EG [RELEASE] knob A 104 C: Cutoff FILTER [CUTOFF] knob A 105 C: Resonance FILTER [RESONANCE] knob A 106 C: Drive Depth DRIVE [DEPTH] knob A 107 C: Effect1 Depth EFFECT [DEPTH] knob A 108 C: Effect1 Rate EFFECT [RATE] knob A 109 C: Effect2 Depth EFFECT [DEPTH] knob A 110 C: Effect2 Rate EFFECT [RATE] knob A 111 C: Drawbar 16' ORGAN FOOTAGE slider [16'] A 112 C: Drawbar 5 1/3 ORGAN FOOTAGE slider [5 1/3'] A 113 C: Drawbar 8' ORGAN FOOTAGE slider [8'] A 114 C: Drawbar 4' ORGAN FOOTAGE slider [4'] A 115 C: Drawbar 2 2/3 ORGAN FOOTAGE slider [2 2/3'] A 116 C: Drawbar 2' ORGAN FOOTAGE slider [2'] A 117 C: Drawbar 1 3/5' ORGAN FOOTAGE slider [1 3/5'] A 118 C: Drawbar 1 1/3' ORGAN FOOTAGE slider [1 1/3'] A 119 C: Drawbar 1' ORGAN FOOTAGE slider [1'] A USB Audio Volume Data List CK88 CK61 Owner’s Manual 55 Table A Table B Table C Table D Parameters Controller Value Transmitted Recognized 0-127 0-127 0-127 Parameters Controller Value Transmitted Recognized -12dB 52 0-5 0-5 -11dB 53 6-10 6-10 -10dB 54 11-15 11-15 -9dB 55 16-20 16-20 -8dB 56 21-25 21-25 -7dB 57 26-30 26-30 -6dB 58 31-35 31-35 -5dB 59 36-40 36-40 -4dB 60 41-46 41-46 -3dB 61 47-51 47-51 -2dB 62 52-56 52-56 -1dB 63 57-61 57-61 0dB 64 62-66 62-66 1dB 65 67-71 67-71 2dB 66 72-76 72-76 3dB 67 77-81 77-81 4dB 68 82-87 82-87 5dB 69 88-92 88-92 6dB 70 93-97 93-97 7dB 71 98-102 98-102 8dB 72 103-107 103-107 9dB 73 108-112 108-112 10dB 74 113-117 113-117 11dB 75 118-122 118-122 12dB 76 123-127 123-127 Parameters Controller Value Transmitted Recognized Slow 0 0-63 Stop 64 64 Fast 127 65-127 Parameters Controller Value Transmitted Recognized 0 0 0 1 1-18 1-18 2 19-36 19-36 3 37-54 37-54 4 55-72 55-72 5 73-90 73-90 6 91-108 91-108 7 109-126 109-126 8 127 127 Data List CK88 CK61 Owner’s Manual 56 MIDI Data Format 1 Scope The specifications described herein apply to transmission and reception of MIDI data by a CK88 or CK61 Stage Keyboard. 2 Compliance The specifications described herein comply with the MIDI 1.0 standard. (1) TRANSMIT FLOW MIDI <-+--[SW1]--+---------NOTE OFF 8nH OUT | | +---------NOTE ON 9nH | | | +---------CONTROL CHANGE | | SUSTAIN BnH,40H | | ASSIGNABLE CONTROLLER BnH,(01H...77H) | | | | | | | | | | | +--[SW3]--BANK SELECT MSB BnH,00H | | BANK SELECT LSB BnH,20H | | | +--[SW4]--PROGRAM CHANGE CnH | | | +---------PITCH BEND CHANGE EnH | +-------------------SYSTEM REALTIME MESSAGE | ACTIVE SENSING FEH | +--[SW2]--+---------SYSTEM EXCLUSIVE MESSAGE | | | +---------<BULK DUMP> | | F0H 43H 0nH 7FH 1CH bhH blH 0BH ahH amH | | alH ddH....ddH ccH F7H | | | +---------<PARAMETER CHANGE> | F0H 43H 1nH 7FH 1CH 0BH ahH amH alH | ddH...ddH F7H | +-------------------SYSTEM EXCLUSIVE MESSAGE IDENTITY REPLY F0H 7EH 7FH 06H 02H 43H 00H 41H ddH ddH mmH 00H 00H 7FH F7H dd: Device family number/code CK61: 62H 06H CK88: 63H 06H mm: version mm =(version no.-1.0) * 10 e.g.)version 1.0 mm =(1.0-1.0) * 10 = 0 version 1.5 mm =(1.5-1.0) * 10 = 5 [SW1] MIDI Transmit Channel Complies with Zone Transmit Channel when the Master Keyboard Mode SW is set to on. Complies with MIDI Transmit Channel in any other case. [SW2] SYSTEM MIDI Device Number When set to “all,” transmitted via “1.” [SW3] SYSTEM Bank Select Switch [SW4] SYSTEM Program Change Switch (2) RECEIVE FLOW MIDI >-+--[SW1]--+---------NOTE OFF 8nH | | | |---------NOTE ON/OFF 9nH | | | +---------CONTROL CHANGE | | MODULATION BnH,01H | | PEDAL WAH BnH,04H | | CHANNEL VOLUME BnH,07H | | EXPRESSION BnH,0BH | | SUSTAIN BnH,40H | | SOSTENUTO BnH,42H | | SOFT BnH,43H | | PORTAMENTO CONTROL BnH,54H | | | +--[SW3]--BANK SELECT MSB BnH,00H | | BANK SELECT LSB BnH,20H | | | +---------CHANNEL MODE MESSAGE | | ALL SOUND OFF BnH,78H | | RESET ALL CONTROLLERS BnH,79H | | ALL NOTES OFF BnH,7BH | | OMNI MODE OFF BnH,7CH | | OMNI MODE ON BnH,7DH | | | +--[SW4]--PROGRAM CHANGE CnH | | | +---------PITCH BEND CHANGE EnH | +-------------------SYSTEM REALTIME MESSAGE | ACTIVE SENSING FEH | +--[SW2]--+---------SYSTEM EXCLUSIVE MESSAGE | | | +---------<BULK DUMP> | | F0H 43H 0nH 7FH 1CH bhH blH 0BH ahH amH | | alH ddH...ddH ccH F7H | | | +---------<PARAMETER CHANGE> | | F0H 43H 1nH 7FH 1CH 0BH ahH amH alH | | ddH...ddH F7H | | | +---------<BULK DUMP REQUEST> | | F0H 43H 2nH 7FH 1CH 0BH ahH amH alH F7H | | | +---------<PARAMETER REQUEST> | F0H 43H 3nH 7FH 1CH 0BH ahH amH alH F7H | +-------------------SYSTEM EXCLUSIVE MESSAGE IDENTITY REQUEST F0H 7EH 0nH 06H 01H F7H [SW1] Complies with MIDI Receive Channel. [SW2] SYSTEM MIDI Device Number [SW3] SYSTEM Bank Select Switch [SW4] SYSTEM Program Change Switch (3) TRANSMIT/RECEIVE DATA (3-1) CHANNEL VOICE MESSAGES (3-1-1) NOTE OFF STATUS 1000nnnn(9nH) n = 0–15 CHANNEL NUMBER NOTE No. 0kkkkkkk k = 0(C-2)–127(G8) VELOCITY 0vvvvvvv v = 64 Transmit (3-1-2) NOTE ON/OFF STATUS 1000nnnn(8nH) n = 0–15 CHANNEL NUMBER NOTE No. 0kkkkkkk k = 0(C-2)–127(G8) VELOCITY NOTE ON 0vvvvvvv(v≠0) NOTE OFF 0vvvvvvv(v=0) (3-1-3) CONTROL CHANGE STATUS 1011nnnn(BnH) n = 0–15 CHANNEL NUMBER CONTROL NUMBER 0ccccccc CONTROL VALUE 0vvvvvvv *TRANSMITTED CONTROL NUMBER c = 0 BANK SELECT MSB ; v = 0 - 127 *1 c = 32 BANK SELECT LSB ; v = 0 - 127 *1 c = 64 SUSTAIN ; v = 0 - 127 *3 c = 1..119 ASSIGNABLE CONTROLLER ; v = 0 - 127 *2 *RECEIVED CONTROL NUMBER c = 0 BANK SELECT MSB ; v = 0 - 127 *1 c = 32 BANK SELECT LSB ; v = 0 - 127 *1 c = 1 MODULATION ; v = 0 - 127 c = 4 PEDAL WAH ; v = 0 - 127 c = 7 CHANNEL VOLUME ; v = 0 - 127 c = 11 EXPRESSION ; v = 0 - 127 c = 64 SUSTAIN ; v = 0 - 127 c = 66 SOSTENUTO ;v=0-63:OFF, 64-127:ON c = 67 SOFT ; v = 0 - 127 c = 84 PORTAMENTO CONTROL ; v = 0 - 127 *1 Relation between BANK SELECT and PROGRAM is as follows: *2 The default CONTROL NUMBERS of ASSIGNABLE CONTROLLER are as follows: MODULATION WHEEL 1 FOOT PEDAL 1 64 FOOT PEDAL 2 11 *3 Foot Pedal Type is set to FC3A (HalfOff) or FC4A/FC5 , the foot pedal operation transmits the value 0 (off) or 127 (on). Bank Select will be actually executed when a Program Change message is received. Bank Select and Program Change numbers that are not supported by this instrument will be ignored. (3-1-4) PROGRAM CHANGE STATUS 1100nnnn(CnH) n = 0–15 CHANNEL NUMBER PROGRAM NUMBER 00000ppp p = 0–7 (3-1-5) PITCH BEND CHANGE STATUS 1110nnnn(EnH) n = 0–15 CHANNEL NUMBER LSB 0vvvvvvv PITCH BEND CHANGE LSB MSB 0vvvvvvv PITCH BEND CHANGE MSB Transmitted with a resolution of 7 bits. (3-2) CHANNEL MODE MESSAGES STATUS 1011nnnn(BnH) n = 0–15 CHANNEL NUMBER CONTROL NUMBER 0ccccccc c = CONTROL NUMBER CONTROL VALUE 0vvvvvvv v = DATA VALUE CATEGORY MSB LSB PROGRAM No. Live Set Page 1 63 0 0..7 : : : Live Set Page 20 63 19 0..7 See the following information for the Control Change to be valid when MIDI Control is set to On. Data List CK88 CK61 Owner’s Manual 57 (3-2-1) ALL SOUND OFF (CONTROL NUMBER = 78H, DATA VALUE = 0) All the sounds currently being played, including channel messages such as note-on of a certain channel, are muted this message is received. (3-2-2) RESET ALL CONTROLLERS (CONTROL NUMBER = 79H, DATA VALUE = 0) Resets the values set for the following controllers. PITCH BEND CHANGE 0 (center) MODULATION 0 (minimum) PEDAL WAH 0 (minimum) EXPRESSION 127 (maximum) SUSTAIN 0 (off) SOSTENUTO 0 (off) SOFT 0 (off) PORTAMENTO CONTROL Clear the reserved note number Doesn’t reset the following data: PROGRAM CHANGE, BANK SELECT MSB/LSB, VOLUME (3-2-3) ALL NOTES OFF (CONTROL NUMBER = 7BH, DATA VALUE = 0) All the notes currently set to on in certain channel(s) are muted when receiving this message. However, if Sustain or Sostenuto is on, notes will continue sounding until these are turned off. (3-2-4) OMNI MODE OFF (CONTROL NUMBER = 7CH, DATA VALUE = 0) Performs the same function as when receiving ALL NOTES OFF. (3-2-5) OMNI MODE ON (CONTROL NUMBER = 7DH, DATA VALUE = 0) Performs the same function as when receiving ALL NOTES OFF. (3-3) SYSTEM REAL TIME MESSAGES (3-3-1) ACTIVE SENSING STATUS 11111110(FEH) Transmitted every 200 msec. Once this code is received, the instrument starts sensing. When neither status messages nor data are received for more than approximately 350 ms, the MIDI receive buffer will be cleared, and the sounds currently being played are forcibly turned off. (3-4) SYSTEM EXCLUSIVE MESSAGE (3-4-1) UNIVERSAL NON REALTIME MESSAGE (3-4-1-1) IDENTITY REQUEST (Receive only) F0H 7EH 0nH 06H 01H F7H (“n” = Device No. However, this instrument receives under “omni.”) (3-4-1-2) IDENTITY REPLY (Transmit only) F0H 7EH 7FH 06H 02H 43H 00H 41H ddH ddH mmH 00H 00H 7FH F7H dd: Device family number/code CK61: 62H 06H CK88: 63H 06H mm: version mm = (version no. - 1.0) * 10 e.g.) version 1.0 mm = (1.0 - 1.0) * 10 = 0 version 1.5 mm = (1.5 - 1.0) * 10 = 5 (3-4-2) UNIVERSAL REALTIME MESSAGE (3-4-3)PARAMETER CHANGE (3-4-3-1) NATIVE PARAMETER CHANGE, MODE CHANGE 11110000 F0 Exclusive status 01000011 43 YAMAHA ID 0001nnnn 1n Device Number 01111111 7F Group ID High 00011100 1C Group ID Low 00001011 0B Model ID 0aaaaaaa aaaaaaa Address High 0aaaaaaa aaaaaaa Address Mid 0aaaaaaa aaaaaaa Address Low 0ddddddd ddddddd Data | | 11110111 F7 End of Exclusive For parameters with data size of 2 or more, the appropriate number of data bytes will be transmitted. See the following MIDI Data Table for Address. (3-4-4) BULK DUMP 11110000 F0 Exclusive status 01000011 43 YAMAHA ID 0000nnnn 0n Device Number 01111111 7F Group ID High 00011100 1C Group ID Low 0bbbbbbb bbbbbbb Byte Count 0bbbbbbb bbbbbbb Byte Count 00001011 0B Model ID 0aaaaaaa aaaaaaa Address High 0aaaaaaa aaaaaaa Address Mid 0aaaaaaa aaaaaaa Address Low 0 0 Data | | 0ccccccc ccccccc Check-sum 11110111 F7 End of Exclusive See the following MIDI Data Table for Address and Byte Count. Checksum is the value that results in a value of 0 for the lower 7 bits when the Byte Count, Start Address, Data and Checksum itself are added. (3-4-5) DUMP REQUEST 11110000 F0 Exclusive status 01000011 43 YAMAHA ID 0010nnnn 2n Device Number 01111111 7F Group ID High 00011100 1C Group ID Low 00001011 0B Model ID 0aaaaaaa aaaaaaa Address High 0aaaaaaa aaaaaaa Address Mid 0aaaaaaa aaaaaaa Address Low 11110111 F7 End of Exclusive See the following MIDI Data Table for Address. (3-4-6) PARAMETER REQUEST 11110000 F0 Exclusive status 01000011 43 YAMAHA ID 0011nnnn 3n Device Number 01111111 7F Group ID High 00011100 1C Group ID Low 00001011 0B Model ID 0aaaaaaa aaaaaaa Address High 0aaaaaaa aaaaaaa Address Mid 0aaaaaaa aaaaaaa Address Low 11110111 F7 End of Exclusive See the following MIDI Data Table for Address. (4) SYSTEM OVERVIEW (Keyboard and Tone Generator) ALL SOUND OFF clears all the sounds in the specific channel(s) played by both the keyboard and the data via MIDI. ALL NOTES OFF received via MIDI clears the sounds in the specific channel(s) played via MIDI. USB Port 2 is enabled when ‘MIDI Port MIDI SW = OFF’ and ‘MIDI Port USB SW = ON’ Keyboard MIDI Out USB Port 1 Part A USB Port 2 MIDI IN USB Port 1 USB Port 2 Zone Settings Zone Mode SW Local Control MIDI Port MIDI SW MIDI Port MIDI SW MIDI Port USB SW Part A External Keyboard SW Part B External Keyboard SW Part C External Keyboard SW MIDI Port USB SW Part B Part C Data List CK88 CK61 Owner’s Manual 58 MIDI Data Table Bank Select Parameter Base Address Group Number = 7F 1C, Model ID = 0B Bulk Dump Block “Top Address” indicates the top address of each block designated by the bulk dump operation. “Byte Count” indicates the data size contained in each block designated by the bulk dump operation. The block from the Bulk Header to the Bulk Footer of the Live Set Sound can be received regardless of their order; however, they cannot be received if an irrelevant Block is included. To execute 1 Live Set Sound bulk dump request, designate its corresponding Bulk Header address. For information about “pp” and “n” shown in the following list, refer to the MIDI PARAMETER CHANGE TABLE (BULK CONTROL). Group Number = 7F 1C, Model ID = 0B n: Device Number gh: Group Number High gl: Group Number Low bh: Byte Count High bl: Byte Count Low id: Model ID ah: Parameter Address High am: Parameter Address Middle al: Parameter Address Low dt: Data cc: Data Checksum MSB LSB Program No. Type Memory Description DEC HEX DEC HEX 63 3F 0 00 0–7 Live Set Sound User Live Set Page 1 1 01 0–7 User Live Set Page 2 2 02 0–7 User Live Set Page 3 3 03 0–7 User Live Set Page 4 4 04 0–7 User Live Set Page 5 5 05 0–7 User Live Set Page 6 6 06 0–7 User Live Set Page 7 7 07 0–7 User Live Set Page 8 8 08 0–7 User Live Set Page 9 9 09 0–7 User Live Set Page 10 10 0A 0–7 User Live Set Page 11 11 0B 0–7 User Live Set Page 12 12 0C 0–7 User Live Set Page 13 13 0D 0–7 User Live Set Page 14 14 0E 0–7 User Live Set Page 15 15 0F 0–7 User Live Set Page 16 16 10 0–7 User Live Set Page 17 17 11 0–7 User Live Set Page 18 18 12 0–7 User Live Set Page 19 19 13 0–7 User Live Set Page 20 Parameter Block Description Top Address High Mid Low System 20 00 00 Common 20 40 00 Master EQ 00 7F 00 Soundmondo Format Version BULK CONTROL 0E 00 00 Header 0F 00 00 Footer STORE TO FLASH 0D 00 00 Store To Flash Live Set Common 46 00 00 Common 46 40 00 Live Set EQ 46 10 00 Audio Trigger Path 4A zz 00 Zone (zz: 00–03) Live Set Part 50 0p 00 Part Parameter Block Description Byte Count Top Address DEC HEX High Mid Low System Common 56 38 20 00 00 Master EQ 20 14 20 40 00 Live Set Sound Bulk Header 0 00 0E pp 0n Soundmondo Format Version 4 04 00 7F 00 Common Common 83 53 46 00 00 Live Set EQ 20 14 46 40 00 Audio Trigger 255 FF 46 10 00 Zone Zone 1 16 10 4A 00 00 : : Zone 4 03 Part Part A 105 69 50 00 00 Part B 01 Part C 02 Bulk Footer 0 00 0F pp 0n Message Type Data Parameter Change F0, 43, 1n, gh, gl, id, ah, am, al, dt, … F7 Parameter Request F0, 43, 3n, gh, gl, id, ah, am, al F7 Bulk Dump F0, 43, 0n, gh, gl, bh, bl, id, ah, am, al, dt, …, cc, F7 Bulk Request F0, 43, 2n, gh, gl, id, ah, am, al, F7 Data List CK88 CK61 Owner’s Manual 59 MIDI PARAMETER CHANGE TABLE (BULK CONTROL) Group Number = 7F 1C, Model ID = 0B SYSTEM Common Group Number = 7F 1C, Model ID = 0B TOTAL SIZE = 56 38 (HEX) Master EQ TOTAL SIZE = 20 14 (HEX) Soundmondo Format Version TOTAL SIZE = 4 4 (HEX) Address Size Data Range (HEX) Parameter Name Description Default (HEX) Notes High Mid Low 0E pp 0n 1 - Bulk Header Live Set Sound User (pp = 0–19, n = 0–7) - 7F 00 1 - Current Sound Buffer - 0F pp 0n 1 - Bulk Footer Live Set Sound User (pp = 0–19, n = 0–7) - 7F 00 1 - Current Sound Buffer - Address Size Data Range Parameter Name Description Default (HEX) Notes High Mid Low 20 00 00 1 reserved 01 1 reserved 02 4 00–00 00–07 00–0F 00–0F Master Tune 414.72–466.78 [Hz] 1st bit3-0: bit15-12 2nd bit3-0: bit11-8 3rd bit3-0: bit 7-4 4th bit3-0: bit 3-0 00 04 00 00 06 1 3D–43 Keyboard Octave Shift −3–0–+3 40 Excluded from the save operation 07 1 34–4C Keyboard Transpose −12–+12 [semitones] 40 Excluded from the save operation 08 1 00–01 Controller Reset Hold, Reset 01 09 1 00–01 Local Control Off, On 01 0A 1 00–0F, 7F Tx Channel 1–16, Off 00 0B 1 00–10 Rx Channel 1–16, All 00 0C 1 00–01 MIDI Control Off, On 00 0D 1 reserved 0E 1 38–48 Output Gain −24–0–+24 [dB] 3E 0F 1 reserved 10 1 00–04 Keyboard Touch Curve Normal, Soft, Hard, Wide, Fixed 00 11 1 01–7F Keyboard Fixed Velocity 1–127 40 12 1 00–01 Transmit/Receive Bank Select Off, On 01 13 1 00–01 Transmit/Receive Program Change Off, On 01 14 1 reserved 15 1 00–01 MIDI In/Out Off, On 01 16 1 00–01 USB In/Out Off, On 01 17 1 reserved 18 1 reserved 19 1 reserved 1A 1 reserved 1B 1 00–01 Value Indication Off, On 01 1C 1 00–01 Controller Mode Jump, Catch 00 1D 1 reserved 1E 1 00–01 LCD Switch Off, On 01 1F 1 36–4A LCD Contrast −10–0–+10 40 20 1 00–01 Panel Lock Live Set Off, On 01 21 1 00–01 Panel Lock Organ Off, On 01 22 1 00–01 Panel Lock Filter/ EG Off, On 01 23 1 00–01 Panel Lock Drive/ Effect Off, On 01 24 1 00–01 Panel Lock Delay/ Reverb Off, On 01 25 1 00–01 Panel Lock Equalizer Off, On 01 26 1 reserved 27 1 reserved 28 1 00–13 Power On Page 1–20 00 29 1 00–07 Power On Sound 1–8 00 2A 1 00–03 Foot Pedal 1– Pedal Type FC3A (Half On), FC3A (HalfOff), FC4A/FC5, FC7 00 2B 1 00–02 Foot Pedal 1–Live Set Inc/Dec Off, Live Set Inc, Live Set Dec 00 2C 1 00–03 Foot Pedal 2– Pedal Type FC3A (Half On), FC3A (HalfOff), FC4A/FC5, FC7 03 2D 1 00–02 Foot Pedal 2–Live Set Inc/Dec Off, Live Set Inc, Live Set Dec 00 2E 1 00–01 Filter/EG Reset Off, On 01 2F 1 00–01 Effect On/Off Reset Off, On 01 30 1 00–02 reserved 31 1 USB Audio Volume 0–127 40 32 1 00–7F Bluetooth Volume 0–127 40 33 1 00–7F A/D Input Type Mic, Line 01 34 1 00–01 USB Audio Loopback Off, On 00 35 1 reserved 36 1 00–01 Speaker EQ Normal, Table 00 37 1 00–01 Speaker Mute Auto, Manual 00 Address Size Data Range Parameter Name Description Default (HEX) Notes High Mid Low 20 40 00 1 34–4C Low Gain −12dB–+12dB 40 Excluded from the save oper- ation 01 1 04–28 Low Frequency 32Hz–2.0kHz 0C 02 1 reserved 03 1 reserved 04 1 reserved 05 1 reserved 06 1 reserved 07 1 reserved 08 1 34–4C Mid Gain −12dB–+12dB 40 Excluded from the save oper- ation 09 1 0E–36 Mid Frequency 100Hz–10kHz 22 0A 1 reserved 0B 1 reserved 0C 1 reserved 0D 1 reserved 0E 1 reserved 0F 1 reserved 10 1 34–4C High Gain −12dB–+12dB 40 Excluded from the save oper- ation 11 1 1C–3A High Frequency 500Hz–16kHz 30 12 1 reserved 13 1 reserved Address Size Data Range Parameter Name Description Default (HEX) Notes High Mid Low 00 7F 00 1 00–7F Soundmondo Format Version Major 01 1 00–7F Soundmondo Format Version Minor 00 1 00–7F Soundmondo Format Version Bugfix 00 1 reserved 00 Address Size Data Range Parameter Name Description Default (HEX) Notes High Mid Low Data List CK88 CK61 Owner’s Manual 60 Live Set Common Common Group Number = 7F 1C, Model ID = 0B Address Size Data Range Parameter Name Description Default (HEX) Notes High Mid Low 46 00 00 1 20–7E Live Set Sound Name 1 32–126 (ASCII) 49 'I' 01 1 20–7E Live Set Sound Name 2 32–126 (ASCII) 6E 'n' 02 1 20–7E Live Set Sound Name 3 32–126 (ASCII) 69 'i' 03 1 20–7E Live Set Sound Name 4 32–126 (ASCII) 74 't' 04 1 20–7E Live Set Sound Name 5 32–126 (ASCII) 20 ' ' 05 1 20–7E Live Set Sound Name 6 32–126 (ASCII) 53 'S' 06 1 20–7E Live Set Sound Name 7 32–126 (ASCII) 6F 'o' 07 1 20–7E Live Set Sound Name 8 32–126 (ASCII) 75 'u' 08 1 20–7E Live Set Sound Name 9 32–126 (ASCII) 6E 'n' 09 1 20–7E Live Set Sound Name 10 32–126 (ASCII) 64 'd' 0A 1 20–7E Live Set Sound Name 11 32–126 (ASCII) 20 0B 1 20–7E Live Set Sound Name 12 32–126 (ASCII) 20 0C 1 20–7E Live Set Sound Name 13 32–126 (ASCII) 20 0D 1 20–7E Live Set Sound Name 14 32–126 (ASCII) 20 0E 1 20–7E Live Set Sound Name 15 32–126 (ASCII) 20 0F 1 reserved 10 1 00–01 Live Set EQ Mode Switch Off, On 00 11 1 00–01 Master Keyboard Mode Switch Off, On 00 12 1 00–01 Advanced Zone Switch Off, On 00 13 2 00–12 00–7F Tempo 42.0–240.0 1st bit6-0  bit13-7 2nd bit6-0  bit6-0 09 30 15 1 34–4C Sound Transpose −12–+12 40 16 1 00–03 Layer Split Mode ABC, A/BC, AB/C, A/B/C 00 17 1 reserved 18 1 01–7F Split Point C # −2–G8 37 Only for splitting in two 19 1 01–7E Split Point A-B C # −2–F # 8 37 Only for splitting in three 1A 1 02–7F Split Point B-C D−2–G8 4F Only for splitting in three 1B 1 reserved 1C 1 00–78 Modulation Wheel Assign 0–119, 120 (USB Audio Volume) For more information, see “Control Change Number” (page 54). 01 1D 1 reserved 1E 1 reserved 1F 1 00–78 Foot Pedal 1 Assign 0–119, 120 (USB Audio Volume) For more information, see “Control Change Number” (page 54). 40 20 1 00–7F Foot Pedal 1 Limit Low 0–127 00 21 1 00–7F Foot Pedal 1 Limit High 0–127 7F 22 1 00–78 Foot Pedal 2 Assign 0–119, 120 (USB Audio Volume) For more information, see “Control Change Number” (page 54). 0B 23 1 00–7F Foot Pedal 2 Limit Low 0–127 00 24 1 00–7F Foot Pedal 2 Limit High 0–127 7F 25 1 reserved 26 1 reserved 27 1 00–01 Delay Switch Off, On 00 28 1 00–03 Delay Type Digital Delay, Analog Delay, Cross Delay, Tempo Delay 00 29 1 00–7F Delay Depth 0–127 40 2A 1 00–7F Delay Time 0–127 40 2B 1 00–0E Delay Tempo Delay Time 1/32 Tri., 1/64 Dot., 1/32, 1/16 Tri., 1/32 Dot., 1/16, 1/8 Tri., 1/16 Dot, 1/8, 1/4 Tri., 1/8 Dot., 1/4, 1/2 Tri., 1/4 Dot., 1/2 0B 2C 1 00–01 Reverb Switch Off, On 01 2D 1 00–02 Reverb Type Hall Reverb, Room Reverb, Plate Reverb 00 2E 1 00–7F Reverb Depth 0–127 14 2F 1 reserved 30 1 00–01 Rotary Speaker Slow/Fast Slow, Fast 00 31 1 00–01 Rotary Speaker Stop Off, On 00 32 1 reserved 33 1 00–01 Audio Trigger Switch Off, On 00 34 1 00–7F Audio Trigger Volume 0–127 40 35 1 00–01 Audio Trigger Key Assign Lowest, Highest 01 36 1 00–02 Audio Trigger Play Mode One Shot, Play/Stop, Play/Pause 00 37 1 reserved 38 1 04–28 A/D Input–EQ Low Freq 32 Hz–2.0 kHz 12 39 1 34–4C A/D Input–EQ Low Gain −12 dB–+12 dB 40 3A 1 0E–36 A/D Input–EQ Mid Freq 100 Hz–10 kHz 29 3B 1 34–4C A/D Input–EQ Mid Gain −12 dB–+12 dB 40 3C 1 1C–3A A/D Input–EQ High Freq 500 Hz–16 kHz 34 3D 1 34–4C A/D Input–EQ High Gain −12 dB–+12 dB 40 3E 1 00–01 A/D Input–Noise Gate Switch Off, On 00 3F 1 36–61 A/D Input–Noise Gate Threshold −73 dB–−30 dB 52 40 1 reserved 41 1 reserved 42 1 reserved 43 1 reserved 44 1 reserved 45 1 00–22 A/D Input–Effect 1 Type *1 00 46 1 00–7F A/D Input–Effect 1 Depth 0–127 40 47 1 00–7F A/D Input–Effect 1 Rate 0–127 40 48 1 reserved 49 1 00–22 A/D Input–Effect 2 Type *1 00 Address Size Data Range Parameter Name Description Default (HEX) Notes High Mid Low Data List CK88 CK61 Owner’s Manual 61 TOTAL SIZE = 83 53 (HEX) *1: G Chorus, SPX Chorus, Symphonic, 816 Chorus, VCM Flanger, Cross FB Flanger, VCM Stereo Phaser, Small Phaser, Max90, Dual Phaser, Tremolo, Auto Pan, Simple Rotary, British Combo, British Lead, Small Stereo, Compressor, Tone Control, 1 BandEQ Narrow, 1 BandEQ Wide, Touch Wah, Pedal Wah, Cross Delay, Digital Delay, Analog Delay, Room Reverb, Hall Reverb, Reverse Reverb, Ring Modulator, Slicer, LP Filter, HP Filter, Lo-Fi, Harmonic Enhancer Live Set EQ TOTAL SIZE = 20 14 (HEX) Audio Trigger TOTAL SIZE = 255 FF (HEX) ZONE Zone Group Number = 7F 1C, Model ID = 0B TOTAL SIZE = 16 10 (HEX) zz = Zone Number 00–03 (HEX) 4A 1 00–7F A/D Input–Effect 2 Depth 0–127 40 4B 1 00–7F A/D Input–Effect 2 Rate 0–127 40 4C 1 00–7F A/D Input–Volume 0–127 7F 4D 1 reserved 4E 1 reserved 4F 1 reserved 50 1 reserved 51 1 reserved 52 1 reserved Address Size Data Range Parameter Name Description Default (HEX) Notes High Mid Low 46 40 00 1 34–4C Low Gain −12 dB–+12 dB 40 01 1 04–28 Low Frequency 32 Hz–2.0 kHz 0C 02 1 reserved 03 1 reserved 04 1 reserved 05 1 reserved 06 1 reserved 07 1 reserved 08 1 34–4C Mid Gain −12 dB–+12 dB 40 09 1 0E–36 Mid Frequency 100 Hz–10 kHz 22 0A 1 reserved 0B 1 reserved 0C 1 reserved 0D 1 reserved 0E 1 reserved 0F 1 reserved 10 1 34–4C High Gain −12 dB–+12 dB 40 11 1 1C–3A High Frequency 500 Hz–16 kHz 30 12 1 reserved 13 1 reserved Address Size Data Range Parameter Name Description Default (HEX) Notes High Mid Low 46 10 00 255 at the maxi- mum Wave File Path 32–127 (ASCII) Address Size Data Range Parameter Name Description Default (HEX) Notes High Mid Low Address Size Data Range Parameter Name Description Default (HEX) Notes High Mid Low 4A zz 00 1 00–01 Zone Switch Off, On 00–01 With Default, only Zone 1 is ON. 01 1 00–0F Transmit Channel 1–16 00–03 With Default, Zone 1 is 0, Zone 2 is 1, Zone 3 is 2, and Zone 4 is 3. 02 1 3D–43 Transpose (Octave) −3–+3 40 03 1 35–4B Transpose (Semitone) −11–+11 40 04 1 00–7F Note Limit Low C−2–G8 00 The highest value is defined with Note Limit High . 05 1 00–7F Note Limit High C−2–G8 7F The lowest value is defined with Note Limit Low . 06 1 reserved 07 1 00–7F MIDI Volume 0–127 7F 08 1 00–7F MIDI Pan L64–C–R63 40 09 1 00–7F MIDI Bank MSB 000–127 00 0A 1 00–7F MIDI Bank LSB 000–127 00 0B 1 00–7F MIDI Program Number 001–128 00 0C 1 00–1F Transmit Bank Select Transmit Program Change Transmit Volume Transmit Pan bit0: Off, On Bank Select bit1: Off, On Program Change bit2: Off, On Volume bit3: Off, On Pan 1F When the Volume is Off , CC#11 (Expres- sion) will not be transmitted. 0D 1 00–3F Transmit PB Transmit Mod Transmit Foot Pedal 1 Transmit Foot Pedal 2 bit0: Off, On PB bit1: Off, On Mod bit2: Off, On Foot Pedal 1 bit3: Off, On Foot Pedal 2 0F 0E 1 reserved 0F 1 reserved Data List CK88 CK61 Owner’s Manual 62 Live Set Part Part Group Number = 7F 1C, Model ID = 0B Address Size Data Range (HEX) Parameter Name Description Default (HEX) Notes High Mid Low 50 0p 00 1 00–09 Current Category 00 01 2 00–7F 00–7F Category 1 Voice Number 0–12 1st bit6-0  bit13-7 2nd bit6-0  bit6-0 00 00 Piano 03 2 00–7F 00–7F Category 2 Voice Number 13–26 1st bit6-0  bit13-7 2nd bit6-0  bit6-0 00 00 E.Piano 05 2 00–7F 00–7F Category 3 Voice Number 27–46 1st bit6-0  bit13-7 2nd bit6-0  bit6-0 00 00 Organ 07 2 00–7F 00–7F Category 4 Voice Number 47–108 1st bit6-0  bit13-7 2nd bit6-0  bit6-0 00 00 Brs/ Wind 09 2 00–7F 00–7F Category 5 Voice Number 109–166 1st bit6-0  bit13-7 2nd bit6-0  bit6-0 00 00 Gtr/Bass 0B 2 00–7F 00–7F Category 6 Voice Number 167–208 1st bit6-0  bit13-7 2nd bit6-0  bit6-0 00 00 Strings 0D 2 00–7F 00–7F Category 7 Voice Number 209–273 1st bit6-0  bit13-7 2nd bit6-0  bit6-0 00 00 Pad 0F 2 00–7F 00–7F Category 8 Voice Number 274–324 1st bit6-0  bit13-7 2nd bit6-0  bit6-0 00 00 Lead 11 2 00–7F 00–7F Category 9 Voice Number 325–350 1st bit6-0  bit13-7 2nd bit6-0  bit6-0 00 00 Chr.Perc 13 2 00–7F 00–7F Category 10 Voice Number 351–362 1st bit6-0  bit13-7 2nd bit6-0  bit6-0 00 00 Others 15 1 reserved 16 1 28–58 Note Shift −24–0–+24 40 17 1 00–7F Part Volume 0–127 7F 18 1 00–0B Part Color 0: Red, 1: Orange, 2: Yellow, 3: Lime, 4: Green, 5: Spring, 6: Cyan, 7: Azure, 8: Blue, 9: Violet, 10: Magenta, 11: Rose A: 02, B: 08, C: 04 19 1 00–01 Part Switch Off, On A: 01, B: 00, C: 00 1A 1 00–01 Part Selected Off, On A: 01, B: 00, C: 00 1B 1 00–01 Effect Select 0: Effect1, 1: Effect2 00 1C 1 reserved 1D 1 reserved 1E 1 reserved 1F 1 reserved 20 1 00–01 Mono/Poly Mono, Poly 01 21 1 00–02 Mono Type Normal, Fingered Portamento, Full- time Portamento 00 Invalid for Organ Flute voice 22 1 reserved 23 1 00–7F Portamento Time 0–127 14 Invalid for Organ Flute voice (for both Porta- mento Time and Porta- mento Time Mode ) 24 1 00–01 Portamento Time Mode Rate, Time 00 25 1 reserved 26 1 reserved 27 1 reserved 28 1 reserved 29 1 reserved 2A 1 reserved 2B 1 reserved 2C 1 00–01 Unison Switch Off, On 00 2D 1 00–02 Unison Type Multi Layer, Harmonics, Sub Harmonics 00 2E 1 00–7F Unison Volume 0–127 7F 2F 1 00–7F Unison Detune 0–127 40 30 1 28–58 Pitch Bend Range −24–0–+24 42 31 1 00–7F Pitch Modulation Depth 0–127 0A 32 1 00–7F Amplifyer Modulation Depth 0–127 00 33 1 00–7F Filter Modulation Depth 0–127 00 34 1 00–7F Modulation Speed −64–0–+63 40 35 1 00–01 Receive Expression Off, On 01 36 1 00–01 Receive Sustain Off, On 01 37 1 00–01 Receive Sostenuto Off, On 01 38 1 00–01 Receive Soft Off, On 01 39 1 00–02 External Keyboard Ext+Int, ExtOnly, Off 00 3A 1 00–7F Touch Sensitivity Depth 0–127 40 3B 1 00–7F Touch Sensitivity Offset 0–127 40 3C 1 reserved 3D 1 reserved 3E 1 reserved 3F 1 reserved 40 1 00–7F Drawbar 16' 0–127 7F Correla- tion between the draw- bar posi- tions and parameter values 0: 0 1: 1–18 2: 19–36 3: 37–54 4: 55–72 5: 73–90 6: 91–108 7: 109– 126 8: 127 41 1 00–7F Drawbar 5 1/3' 0–127 7F 42 1 00–7F Drawbar 8' 0–127 7F 43 1 00–7F Drawbar 4' 0–127 00 44 1 00–7F Drawbar 2 2/3' 0–127 00 45 1 00–7F Drawbar 2' 0–127 00 46 1 00–7F Drawbar 1 3/5' 0–127 00 47 1 00–7F Drawbar 1 1/3' 0–127 00 48 1 00–7F Drawbar 1' 0–127 00 49 1 00–01 Percussion Switch Off, On 00 4A 1 00–01 Percussion Type 3rd, 2nd 00 4B 1 00–01 Percussion Decay Slow, Fast 00 4C 1 00–01 Percussion Volume Normal, Soft 00 4D 1 reserved 4E 1 00–01 Vibrato/Chorus Switch Off, On 00 4F 1 00–05 Vibrato/Chorus Type V1, C1, V2, C2, V3, C3 05 50 1 00–01 Filter Switch Off, On 01 51 1 00–7F Filter Cutoff 0–127 40 52 1 00–7F Filter Resonance 0–127 40 53 1 00–01 EG Switch Off, On 01 54 1 00–7F EG Attack 0–127 40 55 1 00–7F EG Release 0–127 40 Address Size Data Range (HEX) Parameter Name Description Default (HEX) Notes High Mid Low Data List CK88 CK61 Owner’s Manual 63 TOTAL SIZE = 105 69 (HEX) p = Part number 0–2 0: A, 1: B, 2: C *2: G Chorus, SPX Chorus, Symphonic, 816 Chorus, VCM Flanger, Cross FB Flanger, VCM Stereo Phaser, Small Phaser, Max90, Dual Phaser, Tremolo, Auto Pan, Simple Rotary, British Combo, British Lead, Small Stereo, Compressor, Tone Control, 1 BandEQ Narrow, 1 BandEQ Wide, Auto Wah, Touch Wah, Pedal Wah, Cross Delay, Digital Delay, Analog Delay, Room Reverb, Hall Reverb, Reverse Reverb, Ring Modulator, Slicer, LP Filter, HP Filter, Lo-Fi, Damper Resonance, Harmonic Enhancer 56 1 00–01 Drive Switch Off, On 00 57 1 00–04 Drive Type O.Drive, Dist, Rotary A, Rotary B, Comp 00 58 1 00–7F Drive Depth 0–127 40 59 1 00–01 Effect 1 Switch Off, On 00 5A 1 00–23 Effect 1 Type *2 00 5B 1 00–7F Effect 1 Depth 0–127 40 5C 1 00–7F Effect 1 Rate 0–127 40 5D 1 00–01 Effect 2 Switch Off, On 00 5E 1 00–23 Effect 2 Type *2 00 5F 1 00–7F Effect 2 Depth 0–127 40 60 1 00–7F Effect 2 Rate 0–127 40 61 1 reserved 62 1 reserved 63 1 reserved 64 1 reserved 65 1 reserved 66 1 reserved 67 1 reserved 68 1 reserved Address Size Data Range (HEX) Parameter Name Description Default (HEX) Notes High Mid Low Data List CK88 CK61 Owner’s Manual 64 MIDI Implementation Chart Transmitted Function... Recognized Remarks Basic Channel Note Number : True voice Velocity After Touch Pitch Bend Control Change Prog Change : True # System Exclusive : Song Pos. Common : Song Sel. : Tune System : Clock Real Time : Commands : All Sound Off Aux : Reset All Cntrls : Local On/Off Mes- : All Notes Off sages: Active Sense : Reset Notes: Mode Default Changed Note On Note Off Key's Ch's 0,32 1 7,11,67,84 64 66 9,12-31 68-83 85-93 102-119 1-119 1 - 16 1 - 16 O 9nH,v=1-127 X 8nH,v=64 X X O *2 O X O X O *1 O *1 O *1 O *1 O *3 O 0 - 127 *2 X X X X X X X X X O X *1 receive/transmit if MIDI control mode is on. *2 receive/transmit if switch is on. *3 transmit if assigned to controllers. 3 X ************** 0 - 127 ************** O Mode 1 : OMNI ON , POLY Mode 2 : OMNI ON ,MONO Mode 3 : OMNI OFF, POLY Mode 4 : OMNI OFF,MONO O 1 - 16 1 - 16 O 9nH,v=1-127 O 9nH,v=0 or 8nH X X O *2 O O O *2 O *2 O *1 O *1 O *1 O *1 X X X X X X O (120) O (121) X O (123-125) O X 3 X X 0 - 127 0 - 127 O O O : Yes X : No Default Messages Altered YAMAHA [Stage Keyboard] Date :16-JUL-2021 Model CK88 CK61 MIDI Implementation Chart Version : 1.0 Memorized Memorized Bank Select Sustain Sw Sostenuto O 0 - 7 *2 Data List CK88 CK61 Owner’s Manual 65 Apache License 2.0 Copyright (c) 2009-2018 Arm Limited. All rights reserved. SPDX-License-Identifier: Apache-2.0 Licensed under the Apache License, Version 2.0 (the License); you may not use this file except in compliance with the License. You may obtain a copy of the License at www.apache.org/licenses/LICENSE-2.0 Unless required by applicable law or agreed to in writing, software distributed under the License is distributed on an AS IS BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the License for the specific language governing permissions and limitations under the License. The Clear BSD license The Clear BSD License Copyright 1997-2016 Freescale Semiconductor, Inc. Copyright 2016-2018 NXP All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted (subject to the limitations in the disclaimer below) provided that the following conditions are met: Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. Neither the name of the copyright holder nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission. NO EXPRESS OR IMPLIED LICENSES TO ANY PARTY'S PATENT RIGHTS ARE GRANTED BY THIS LICENSE. THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Modified BSD license COPYRIGHT(c) 2016 STMicroelectronics Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. 3. Neither the name of STMicroelectronics nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission. THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. CK88 CK61 Owner’s Manual 66 Troubleshooting If the CK does not behave as expected—for example, not producing the correct sound or producing no sound at all—you can try to resolve the issue as described below. Many issues can also be resolved by carrying out the Factory Reset (page 67) operation. If any specific issue should persist, please contact your Yamaha dealer or a service center (see the back of this booklet). Other information Issue Suspected cause Solution The CK turns off unexpectedly. This is normal when the Auto Power Off function is enabled. If necessary, you can disable the Auto Power Off function to prevent it from turning off the CK again (page 36). No sound is produced. All the Part [ON/OFF] buttons are OFF. Set the desired Part [ON/OFF] button to ON. The Part volume is turned fully down. Use the Part Volume sliders to adjust the volume. Local Control is set to Off . When Local Control is set to Off , the internal tone generator will not play a sound when you play the keyboard. Set Local Control to On (page 37). MIDI volume or expression has been set to a very low level by an external MIDI controller. Try changing a Live Set Sound. If a pedal has been connected to the FOOT PEDAL jacks, move the pedal to change the volume. No sound is produced from the built-in speakers. SPEAKERS switch is set to OFF. Set the SPEAKERS switch to ON. When the headphones are connected, the built-in speakers may be muted in certain settings as shown below. • When the [MENU] button  General  System  Speaker  Speaker Mute is set to Auto . • When the [MENU] button  General  System  Speaker  Speaker Mute is set to Manual and the SPEAKERS switch is set to OFF. Disconnect the headphones. Set the SPEAKERS switch to ON. No sound is produced from the connected external device. Power to the CK or the connected external audio device is not turned on. Check the power to the CK and the connected external audio device is turned on. The volume of the CK and the connected external audio equipment are turned fully down. Adjust the volume. Use the [MASTER VOLUME] slider to adjust the volume. If a pedal has been connected to the FOOT PEDAL jacks, try moving the pedals. A sound continues to play indefinitely. An Effect (such as delay) continues. Lower the [DEPTH] knob or set the EFFECT1 or EFFECT2 [ON/OFF] button to OFF. If a Live Set Sound has been changed while a sound continues to play, try selecting a different Live Set Sound. Sounds are distorted. Effect settings are not appropriate. Sound will be distorted depending on the effect types and the settings. Change the effect types and the settings. Volume is set too high. Output Gain is set too high. Adjust the volume. To adjust the overall volume of the CK, move the [MASTER VOLUME] slider. Or, use the [MENU] button  General  Audio  Output Gain (page 38). Other information CK88 CK61 Owner’s Manual 67 Restoring the Factory Default Settings ( Factory Reset ) The Factory Reset function allows you to restore the CK to its initial condition. NOTICE When the Factory Reset function is carried out, all the Live Set Sounds you have stored, as well as the settings of MENU screens and SETTINGS screens will be overwritten with their defaults. It is wise, therefore, to regularly save backups of important settings on a USB flash drive.  Carrying out the Factory Reset To reset all values to the factory defaults, press the [MENU] button  Job  Factory Reset (page 40). Sounds are distorted. The Volume of the connected external audio device is set too high. Adjust the volume of the connected external audio device or use the A/D INPUT [GAIN] knob of the CK. Or, you can also adjust the volume from the [MENU] button  General  Audio  USB Audio Volume (page 38). Sound output is intermittent and stutters. The total number of notes has exceeded the maximum polyphony (128 notes). Be careful not to exceed the maximum polyphony. No effect is applied. Effects are set to OFF. Set the effects ON with the EFFECT 1 [ON/ OFF] button or the EFFECT 2 [ON/OFF] button. The depth is turned to the minimum level. Use the [DEPTH] knob to adjust the effect depth. Moving the Pitch Bend Wheel or Modulation Wheel does not change the sound. The value is set to “0.” Change the value. Nothing is shown on the Display (LCD). The [MENU] button  General  Control Panel  Display  LCD Switch is set to Off . Make sure to set the [MENU] button  General  Control Panel  Display  LCD Switch to On (page 38). If the menu items are not visible, adjust the contrast from the [MENU] button  General  Control Panel  Display  LCD Contrast (page 38). A pedal does not work. The pedal type is not correct. Set from the [MENU] button  General  Foot Pedal  Pedal 1 or Pedal 2 (page 39). The pedal is not correctly connected. Make sure that the pedal’s plug is fully and firmly inserted. Receive SW is turned off. From the [SETTINGS] button  Controllers  Receive SW , select a pedal and set it to ON (page 31). Cannot save files to the external USB flash drive. The USB flash drive is write-protected. Disable the write protection. The USB flash drive is not formatted properly. Format the USB flash drive again. Communication between the computer and the CK does not work properly. The Port settings on the computer are not appropriate. Check the port settings on the computer. MIDI bulk data transmission does not work properly. Use of the wrong terminals (MIDI or USB). Check the settings. Wrong MIDI device number. Check the MIDI device number. Issue Suspected cause Solution Other information CK88 CK61 Owner’s Manual 68 Display messages Messages Description Auto power off disabled. This message appears when Auto Power Off is disabled. Bluetooth pairing...Press [EXIT] button to cancel pairing. The Bluetooth device and the CK are being paired. Press the [EXIT] button to cancel pairing. Change [Pedal Live Set Inc/Dec] to [Off]. Before changing the foot pedal assignment from the [SETTINGS] button, you need to set the Live Set Inc/Dec parameter to off from the [MENU] button. Completed. The specified operation (Load, Save, Format or another Job) has been completed. Connect a USB device. There is no connected USB device. Connecting to USB device… Currently recognizing the USB flash drive connected to the USB [TO DEVICE] terminal. Device number is off. Bulk data cannot be transmitted or received because the device number is off. Device number mismatch. Bulk data cannot be received because the device numbers do not match. File or folder already exists. A file or a folder having the same name as the one you are about to save already exists. File or folder path is too long. The file or folder cannot be accessed because the maximum length for the file name or the pathname has been exceeded. Illegal bulk data. An error occurred while receiving a Bulk data or Bulk Request message. Illegal file name. The specified file name is invalid. Try entering a different name. Illegal file. The specified file is unusable by the CK or cannot be loaded. Incompatible USB device. A USB device that cannot be used with the CK has been connected to the USB [TO DEVICE] terminal. Low Battery! The batteries are low. Replace the batteries. MIDI buffer full. Failed to process the MIDI data because too much data was received at one time. MIDI checksum error. An error occurred when receiving bulk data. No read/write authority to the file. Indicates that you do not have the authority to read or write to the file. Now receiving MIDI bulk data… Indicates the CK is receiving MIDI bulk data. Now transmitting MIDI bulk data… Indicates the CK is transmitting MIDI bulk data. Please reboot to maintain internal memory. Reboot the CK to restore the internal memory. Press both [ENTER]+[MENU] buttons. Press the [ENTER] button and the [MENU] button simultaneously to disable the panel lock. Speaker EQ is set to [Table]. Speaker EQ has been set to Table . Split Point does not exist. Cannot change the Split Point because it has not been set. Unsupported USB device. This message appears when the connected USB flash drive is either unformatted, or formatted in a way that the CK does not support. Please format the USB flash drive using the CK. USB connection terminated. Communication with the USB flash drive has been shut down due to overcurrent to the USB flash drive. Disconnect the USB flash drive from the USB [TO DEVICE] terminal, and then reboot the CK. USB device is full. The USB flash drive is full and no more data can be saved. Use a new USB flash drive, or make space by erasing unwanted data from the USB flash drive. USB device is write-protected. This message appears when you have attempted to write to a protected USB flash drive. USB device read/write error. An error occurred while reading from or writing to a USB flash drive. Other information CK88 CK61 Owner’s Manual 69 Specifications The contents of this manual apply to the latest specifications as of the publishing date. To obtain the latest manual, access the Yamaha website then download the manual file. Since specifications, equipment or separately sold accessories may not be the same in every locale, please check with your Yamaha dealer. Item Details CK88 CK61 Keyboard Type GHS keyboard: matte black keytops FSB keyboard, initial touch Number of Keys 88 61 Tone Generation Tone Generation Technology AWM2, AWM (Organ Flutes) Polyphony (max.) 128 Voices Number of Live Set Sounds 160 (Preset Live Set Sounds: 80) Number of Voices 363 Effects Insertion Effect Drive 1 system (5 types) Effect 2 systems (1: 36 types, 2: 36 types) Delay 4 types Reverb 3 types Master EQ 3-band Display Type Full Dot LCD (128 × 64 dots) Connectivity OUTPUT [L/MONO]/[R] (6.3 mm, standard phone jacks, unbalanced) A/D INPUT [L/MONO]/[R] (6.3 mm, standard phone jacks) [PHONES] (6.3 mm, standard stereo phone jack) FOOT PEDAL [1]/[2] MIDI [IN]/[OUT] USB [TO HOST]/[TO DEVICE] [DC IN] Bluetooth (May not have this functionality depending on the country in which you purchased the product.) Bluetooth version 4.1 Supported profile A2DP Compatible codec SBC Wireless output Bluetooth class 2 Maximum communication distance about 10 m Radio Frequency (Operational Frequency) 2401–2481 MHz Maximum output power (EIRP) 4 dBm Type of modulation FHSS USB audio interface Sampling Frequency 44.1 kHz Channels In: 2 channels (1 stereo channel) Out: 2 channels (1 stereo channel) Sound System Amplifiers 6 W × 2 Speakers (12 cm × 6 cm) × 2, Switchable ON/OFF Power Supply Power Supply AC adaptor PA-150B or an equivalent recommended by Yamaha (Output: DC 12V, 1.5 A) Batteries Eight “AA” size alkaline (LR6) or Ni-MH rechargeable batteries Power Consumption 11 W (When using PA-150B AC adaptor) Standby Power Consumption 0.3 W Size/Weight Dimensions (W × D × H) 1333 mm × 354 mm × 148 mm (52-1/2 inch × 13-15/16 inch × 5-13/16 inch) 910 mm × 291 mm × 109 mm (35-13/16 inch × 11-7/16 inch × 4-5/16 inch) Weight 13.1 kg (28 lb 14 oz) (not including batteries) 5.6 kg (12 lb 6 oz) (not including batteries) Included Accessories AC adaptor*, Owner’s Manual *May be included depending on your locale Other information CK88 CK61 Owner’s Manual 70 Index Symbols .wav ..........................................................................................................25 .wav See also audio file A audio file ..................................................................................19, 25, 32 Audio Trigger ................................................................................12, 24 B Backup ....................................................................................................27 Bluetooth pairing ................................................................................46 built-in speakers ..................................................................................36 E Edit Recall .......................................................................................25, 40 External Keyboard ..............................................................................32 F Factory default. See also Factory Reset Factory Reset .................................................................................40, 67 File type ..................................................................................................27 Foot Controller ......................................................................18, 31, 37 Foot Pedal ..............................................................................................18 I Initialize factory reset ................................................................................67 Live Set Sound ............................................................................26 MENU .............................................................................................40 L Live Set Overview ................................................................................. 9 Load Backup File ...........................................................................27, 41 M Master Keyboard ..........................................................................24, 33 Master Tune ..........................................................................................36 Mic input .........................................................................................25, 38 Modulation .......................................................................10, 29, 31, 37 N Note Shift ...............................................................................................29 P Panel lock .................................................................................24, 38, 42 Portamento ....................................................................................14, 28 S Save saving settings to a USB flash drive ....................................27 saving settings to the CK. See also Store Speaker EQ .............................................................................................36 Speakers built-in speakers .........................................................................18 Store ..................................................................................................14, 24 Sustain ..............................................................................................18, 31 T Touch Sensitivity ..........................................................................29, 30 U USB Audio .......................................................................................31, 38 USB MIDI .................................................................................................19 Y Yamaha Steinberg USB Driver ........................................................47 MEMO Deutsch Français Nederlands Español Italiano Português ǼȜȜȘȞȚțȐ Svenska Norsk Dansk Suomi Polski ýHãWLQD Magyar Eesti /DWYLHãX /LHWXYLǐ 6ORYHQþLQD 6ORYHQãþLQD Ȼɴɥɝɚɪɫɤɢ 5RPkQă English Hrvatski Türkçe Important Notice: Power management information for customers in European Economic Area (EEA), Switzerland and Turkey Remarque importante : Informations sur la gestion de l'alimentation pour les clients de l'Espace économique européen (EEE), de Suisse et de Turquie Yamaha-Produkte sind mit einer Power-Management-Funktion ausgestattet. Bei einigen Produkten können Sie diese Funktion ausschalten oder die Zeitdauer, die verstreicht, bis das Instrument ausgeschaltet oder in Bereitschaft versetzt wird, verlängern. In diesen Fällen erhöht sich der Energieverbrauch. Les produits Yamaha sont équipés d’une fonction de gestion de l’alimentation. Certains produits vous permettent de désactiver cette fonction ou d'allonger le délai avant la mise hors tension ou la mise en veille. Dans ces cas, la consommation d’énergie augmente. Yamaha-producten zijn uitgerust met een energiebeheerfunctie. Bij sommige producten kunt u die functie uitschakelen of de tijd verlengen die verstrijkt voordat de stroom wordt uitgeschakeld of in stand-by wordt gezet. In deze gevallen zal het energieverbruik toenemen. Los productos Yamaha están equipados con una función de administración de energía. Algunos productos permiten desactivar esa función o ampliar el tiempo que transcurre antes de apagar la alimentación o poner el producto en modo de espera. En estos casos, el consumo de energía aumentará. I prodotti Yamaha sono dotati di una funzione di gestione dell'alimentazione. Alcuni prodotti consentono di disattivare tale funzione o di estendere il periodo di tempo che trascorre prima che l'alimentazione venga spenta o impostata in standby. In questi casi, il consumo energetico aumenterà. Yamaha products are equipped with a power management function. Some products allow you to disable that function, or to extend the amount of time that elapses before the power is turned off or set to standby. In these cases, energy consumption will increase. Os produtos Yamaha são equipados com uma função de gerenciamento de energia. Alguns produtos permitem desativar essa função ou estender o tempo decorrido antes de se desligar ou entrar em standby. Nesses casos, o consumo de energia aumentará. ȉĮʌȡȠȧȩȞIJĮIJȘȢ<DPDKDİȓȞĮȚİȟȠʌȜȚıȝȑȞĮȝİȝȚĮȜİȚIJȠȣȡȖȓĮįȚĮȤİȓȡȚıȘȢȚıȤȪȠȢȅȡȚıȝȑȞĮʌȡȠȧȩȞIJĮıȐȢįȓȞȠȣȞIJȘįȣȞĮIJȩIJȘIJĮȞĮ ĮʌİȞİȡȖȠʌȠȚİȓIJİĮȣIJȒIJȘȜİȚIJȠȣȡȖȓĮȒȞĮİʌİțIJİȓȞİIJİIJȠȤȡȠȞȚțȩįȚȐıIJȘȝĮȝȑȤȡȚIJȘȞĮʌİȞİȡȖȠʌȠȓȘıȘȒIJȘșȑıȘıİțĮIJȐıIJĮıȘĮȞĮȝȠȞȒȢȈİ ĮȣIJȑȢIJȚȢʌİȡȚʌIJȫıİȚȢȘțĮIJĮȞȐȜȦıȘİȞȑȡȖİȚĮȢșĮĮȣȟȘșİȓ Yamaha-produkterna är utrustade med en energihanteringsfunktion. För vissa produkter kan du inaktivera den funktionen eller för att förlänga tiden som förflutit innan strömmen stängs av eller ställs i vänteläge. I dessa fall ökar energiförbrukningen. Yamahas produkter har en strømstyringsfunktion. På nogle produkter er det muligt at deaktivere denne funktion eller at forlænge den tid, der går, før der slukkes for strømmen, eller sættes på standby. I disse tilfælde vil strømforbruget stige. Yamaha-tuotteet on varustettu virranhallintatoiminnolla. Joissakin tuotteissa voit poistaa toiminnon käytöstä tai pidentää aikaa, joka kuluu ennen virran katkaisemista tai valmiustilaan asettamista. Näissä tapauksissa energiankulutus kasvaa. 3URGXNW\<DPDKDVąZ\SRVDĪRQHZIXQNFMĊ]DU]ąG]DQLDHQHUJLą1LHNWyUHSURGXNW\XPRĪOLZLDMąZ\áąF]HQLHWHMIXQNFMLOXEZ\GáXĪHQLHF]DVX MDNLXSá\ZDGRZ\áąF]HQLD]DVLODQLDOXESU]HMĞFLDZWU\EJRWRZRĞFL:WDNLFKSU]\SDGNDFK]XĪ\FLHHQHUJLLZ]URĞQLH 3URGXNW\<DPDKDMVRXY\EDYHQ\IXQNFtVSUiY\QDSiMHQt1ČNWHUpSURGXNW\XPRåĖXMtWXWRIXQNFL]DNi]DWQHERSURGORXåLWGREXNWHUiPi XEČKQRXWSĜHGY\SQXWtPQDSiMHQtQHERSRKRWRYRVWQtPUHåLPHP9WČFKWRSĜtSDGHFKVH]YêãtVSRWĜHEDHOHNWĜLQ\ $<DPDKDWHUPpNHNHQHUJLDPHQHG]VPHQWIXQNFLyYDOYDQQDNHOOiWYD(J\HVWHUPpNHNOHKHWĘYpWHV]LNKRJ\OHWLOWVDH]WDIXQNFLyWYDJ\ PHJKRVV]DEEtWVDDNLNDSFVROiVYDJ\NpV]HQOpWLiOODSRWEDKHO\H]pVHOĘWWHOWHOWLGĘW(]HNEHQD]HVHWHNEHQD]HQHUJLDIRJ\DV]WiVQ|YHNHGQLIRJ Yamaha tooted on varustatud toitehalduse funktsiooniga. Mõned tooted võimaldavad teil selle funktsiooni keelata või pikendada aega, mis P||GXEHQQHWRLWHYlOMDOOLWDPLVWY}LRRWHUHåLLPLVHDGPLVW6HOOLVWHOMXKWXGHOVXXUHQHEHQHUJLDWWDUELPLQH <DPDKDL]VWUƗGƗMXPLLUDSUƯNRWLDUEDURãDQDVSƗUYDOGƯEDVIXQNFLMX'DåLHPL]VWUƗGƗMXPLHPãRIXQNFLMXYDUDWVSƝMRWYDLSDLOG]LQƗWODLNXNDP MƗSDLHWSLUPVEDURãDQDVDWVOƝJãDQDVYDLSƗULHãDQDVJDLGVWƗYHVUHåƯPƗâƗGƗJDGƯMXPƗSDOLHOLQƗVLHVHQHUƧLMDVSDWƝULƼã Ä<DPDKD³JDPLQLXRVH\UDHQHUJLMRVVąQDXGǐYDOG\PRIXQNFLMD.DLNXULHJDPLQLDLOHLGåLDLãMXQJWLãLąIXQNFLMąDUEDSUDWĊVWLODLNąSUDơMXVƳSULHã LãMXQJLDQWPDLWLQLPąDUEDƳMXQJLDQWEXGơMLPRUHåLPą7RNLDLVDWYHMDLVHQHUJLMRVVXYDUWRMLPDVSDGLGơV 3URGXNW\VSRORþQRVWL<DPDKDV~Y\EDYHQpIXQNFLRXVSUiY\QDSiMDQLD1LHNWRUpSURGXNW\YiPXPRåĖXM~W~WRIXQNFLXY\SQ~ĢDOHERSUHGĎåLĢþDV SRXSO\QXWtNWRUêFKVDQDSiMDQLHY\SQHDOHERQDVWDYtGRSRKRWRYRVWQpKRUHåLPX9WDNêFKWRSUtSDGRFKVD]YêãLVSRWUHEDHQHUJLH <DPDKLQLL]GHONLLPDMRIXQNFLMRXSUDYOMDQMD]QDSDMDQMHP1HNDWHULL]GHONLYDPRPRJRþDMRGDRQHPRJRþLWHWRIXQNFLMRDOLSRGDOMãDWHþDVNLPRUD SUHWHþLSUHGHQVHQDSDMDQMHL]NORSLDOLQDVWDYLYVWDQMHSULSUDYOMHQRVWL9WHKSULPHULKVHERSRUDEDHQHUJLMHSRYHþDOD ɉɪɨɞɭɤɬɢɬɟɧɚ<DPDKDɫɚɫɧɚɛɞɟɧɢɫɮɭɧɤɰɢɹɡɚɭɩɪɚɜɥɟɧɢɟɧɚɡɚɯɪɚɧɜɚɧɟɬɨɇɹɤɨɢɩɪɨɞɭɤɬɢɜɢɩɨɡɜɨɥɹɜɚɬɞɚɡɚɛɪɚɧɢɬɟɬɚɡɢ ɮɭɧɤɰɢɹɢɥɢɞɚɭɞɴɥɠɢɬɟɜɪɟɦɟɬɨɤɨɟɬɨɳɟɢɡɬɟɱɟɩɪɟɞɢɡɚɯɪɚɧɜɚɧɟɬɨɞɚɫɟɢɡɤɥɸɱɢɢɥɢɞɚɫɟɧɚɫɬɪɨɢɜɪɟɠɢɦɧɚɝɨɬɨɜɧɨɫɬ ȼɬɟɡɢɫɥɭɱɚɢɤɨɧɫɭɦɚɰɢɹɬɚɧɚɟɧɟɪɝɢɹɳɟɫɟɭɜɟɥɢɱɢ 3URGXVHOHDPDKDVXQWHFKLSDWHFXRIXQF܊LHGHJHVWLRQDUHDHQHUJLHL8QHOHSURGXVHYăSHUPLWVăGH]DFWLYD܊LDFHDVWăIXQF܊LHVDXVăSUHOXQJL܊L SHULRDGDGHWLPSFDUHWUHFHvQDLQWHFDDOLPHQWDUHDVăILHRSULWăVDXVHWDWăvQVWDQGE\ÌQDFHVWHFD]XULFRQVXPXOGHHQHUJLHYDFUH܈WH <DPDKDSURL]YRGLRSUHPOMHQLVXIXQNFLMRPXSUDYOMDQMDSRWURãQMRPHQHUJLMH1HNLYDPSURL]YRGLRPRJXüXMXRQHPRJXüDYDQMHWHIXQNFLMHLOL SURGXOMHQMHYUHPHQDNRMHSURWHNQHSULMHLVNOMXþLYDQMDQDSDMDQMDLOLSRVWDYOMDQMDXVWDQMHSULSUDYQRVWL8WLPüHVHVOXþDMHYLPDSRYHüDWLSRWURãQMD energije. <DPDKDUQOHULQGHJo\|QHWLPLLúOHYLYDUGÕU%D]ՁUQOHUEXLúOHYLGHYUHGÕúÕEÕUDNPDQÕ]DYH\DJoNDSDWÕOPDGDQ\DGDEHNOHPHPRGXQD DOÕQPDGDQ|QFHJHoHQVUH\LX]DWPDQÕ]DRODQDNWDQÕU%XJLELGXUXPODUGDHQHUMLWNHWLPLDUWDFDNWÕU MEMO MEMO Important Notice: U.S. LIMITED WARRANTY for Customers in the United States For detailed information about this Yamaha product and warranty service, please either visit the following website address (printable file is available at our website) or contact Customer Service at the address or telephone number identified below. Website Address: Yamaha.io/SynthAndStageWarranty Customer Service: Yamaha Corporation of America 6600 Orangethorpe Avenue, Buena Park, CA 90620-1273 Telephone: 800-854-1569 Yamaha Worldwide Representative Offices For details on the product(s), contact your nearest Yamaha representative or the authorized distributor, found by accessing the 2D barcode below. English Wenden Sie sich für nähere Informationen zu Produkten an eine Yamaha-Vertretung oder einen autorisierten Händler in Ihrer Nähe. Diese finden Sie mithilfe des unten abgebildeten 2D-Strichodes. Deutsch Pour obtenir des informations sur le ou les produits, contactez votre représentant ou revendeur agréé Yamaha le plus proche. Vous le trouverez à l'aide du code-barres 2D ci-dessous. Français Para ver información detallada sobre el producto, contacte con su representante o distribuidor autorizado Yamaha más cercano. Lo encontrará escaneando el siguiente código de barras 2D. Español Neem voor meer informatie over de producten contact op met uw dichtstbijzijnde Yamaha-vertegenwoordiger of de geautoriseerde distributeur, te vinden via de onderstaande 2D-barcode. Nederlands Para mais informações sobre o(s) produto(s), fale com seu representante da Yamaha mais próximo ou com o distribuidor autorizado acessando o código de barras 2D abaixo. Português $E\X]\VNDüV]F]HJyáRZHLQIRUPDFMHQDWHPDWSURGXNWyZ VNRQWDNWXMVLĊ]QDMEOLĪV]\PSU]HGVWDZLFLHOHPILUP\<DPDKDOXE autoryzowanym dystrybutorem, którego znajdziesz za SRĞUHGQLFWZHPSRQLĪV]HJRNRGXNUHVNRZHJR' Polski ɑɬɨɛɵɭɡɧɚɬɶɩɨɞɪɨɛɧɟɟɨɩɪɨɞɭɤɬɟ ɩɪɨɞɭɤɬɚɯ ɫɜɹɠɢɬɟɫɶ ɫɛɥɢɠɚɣɲɢɦɩɪɟɞɫɬɚɜɢɬɟɥɟɦɢɥɢɚɜɬɨɪɢɡɨɜɚɧɧɵɦ ɞɢɫɬɪɢɛɶɸɬɨɪɨɦ<DPDKDɜɨɫɩɨɥɶɡɨɜɚɜɲɢɫɶɞɜɭɯɦɟɪɧɵɦ ɲɬɪɢɯɤɨɞɨɦɧɢɠɟ Ɋɭɫɫɤɢɣ Om du vill ha mer information om produkterna kan du kontakta närmaste Yamaha-representant eller auktoriserade distributör med hjälp av 2D-streckkoden nedan. Svenska Hvis du vil have detaljer om produktet/produkterne, kan du kontakte den nærmeste Yamaha-repræsentant eller autoriserede Yamaha-distributør, som du finder ved at scanne 2D-stregkode nedenfor. Dansk https://manual.yamaha.com/mi/address_list/ Head Office/Manufacturer: Yamaha Corporation 10-1, Nakazawa-cho, Chuo-ku, Hamamatsu, 430-8650, Japan Importer (European Union): Yamaha Music Europe GmbH Siemensstrasse 22-34, 25462 Rellingen, Germany Importer (United Kingdom): Yamaha Music Europe GmbH (UK) Sherbourne Drive, Tilbrook, Milton Keynes, MK7 8BL, United Kingdom DMI37_22m Per dettagli sui prodotti, contattare il rappresentante Yamaha o il distributore autorizzato più vicino, che è possibile trovare tramite il codice a barre 2D in basso. Italiano 3RGUREQRVWLRSURGXNWX HFK ]tVNiWHRGQHMEOLåãtKR]iVWXSFH VSROHþQRVWL<DPDKDQHERDXWRUL]RYDQpKRGLVWULEXWRUDNWHUêE\O QDOH]HQSĜLSRXåLWt'þiURYpKRNyGXQtåH ýHãWLQD 3RGUREQpLQIRUPiFLHRSURGXNWH RFK YiPSRVN\WQHQDMEOLåãt ]iVWXSFDVSRORþQRVWL<DPDKDDOHERDXWRUL]RYDQêGLVWULE~WRU NWRUpKRQiMGHWHSRPRFRXQLåãLHXYHGHQpKR'þLDURYpKRNyGX 6ORYHQþLQD A termék(ek)re vonatkozó részletekért forduljon a legközelebbi Yamaha képviselethez vagy a hivatalos forgalmazóhoz, amelyet az alábbi 2D vonalkód segítségével találhat meg. Magyar ýHåHOLWHSRGUREQHMãHLQIRUPDFLMHRL]GHONLKVHREUQLWHQD QDMEOLåMHJD<DPDKLQHJDSUHGVWDYQLNDDOLSRREODãþHQHJD distributerja, ki ga najdete prek 2D-kode v nadaljevanju. 6ORYHQãþLQD /DLLHJnjWXSODãƗNXLQIRUPƗFLMXSDUL]VWUƗGƗMXPLHPVD]LQLHWLHV DUWXYƗNR<DPDKDSƗUVWƗYLYDLSLOQYDURWRL]SODWƯWƗMXNXUX DWUDGƯVLHWL]PDQWRMRWWƗOƗNSLHHMDPR'VYƯWUNRGX /DWYLHãX Ɂɚɩɨɞɪɨɛɧɨɫɬɢɨɬɧɨɫɧɨɩɪɨɞɭɤɬɚɢɬɟɫɟɫɜɴɪɠɟɬɟɫɧɚɣɛɥɢɡɤɢɹ ɩɪɟɞɫɬɚɜɢɬɟɥɧɚ<DPDKDɢɥɢɨɬɨɪɢɡɢɪɚɧɞɢɫɬɪɢɛɭɬɨɪɤɨɣɬɨ ɦɨɠɟɬɟɞɚɨɬɤɪɢɟɬɟɤɚɬɨɢɡɩɨɥɡɜɚɬɟ'ɛɚɪɤɨɞɚɩɨɞɨɥɭ Ȼɴɥɝɚɪɫɤɢ 1RUơGDPLJDXWLGDXJLDXLQIRUPDFLMRVDSLHJDPLQƳ LXV  NUHLSNLWơVƳDUWLPLDXVLąÄ<DPDKD³DWVWRYąDUEDƳJDOLRWąMƳ SODWLQWRMąNXUƳUDVLWHQXVNDLWĊWROLDXSDWHLNWą'EUnjNãQLQƳNRGą /LHWXYLǐ Toodete kohta täpsema teabe saamiseks võtke ühendust lähima Yamaha esindaja või autoriseeritud levitajaga, kelle leiate allpool asuva 2D-vöötkoodi kaudu. Eesti hUQOHUKDNNÕQGDD\UÕQWÕODULoLQDúD÷ÕGDNL'NRGOXPRWRUD HULúHUHNEXOXQDQVL]HHQ\DNÕQ<DPDKDWHPVLOFLVLQHYH\D\HWNLOL ED\L\HEDúYXUXQ Türkçe Za detalje o proizvodima obratite se lokalnom predstavku ili RYODãWHQRPGLVWULEXWHUXWYUWNH<DPDKDNRMHJPRåHWHSURQDüL VNHQLUDQMHP'FUWLþQRJNRGDXQDVWDYNX Hrvatski 3HQWUXGHWDOLLSULYLQGSURGXVHOHFRQWDFWD܊LFHOPDLDSURSLDW reprezentant Yamaha sau distribuitorul autorizat, pe care îl SXWH܊LJăVLDFFHVkQGFRGXOGHEDUH'GHPDLMRV 5RPkQă 10-1 Nakazawa-cho, Chuo-ku, Hamamatsu, 430-8650 Japan © 2022 Yamaha Corporation Published 04/2025 MWMA-E0 VJG0290